MSDS

ManualsBrandsCRC ManualsChemicals & Cleaning SuppliesFOOD GRADE MOLD RELEASE WO

SAFETY DATA SHEET

1. Identification

Food Grade Mold Release WOProduct identifier

Other means of identification

03311

Product code

Mold release lubricant

Recommended use

None known.

Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Company name

CRC Industries, Inc.

Address

885 Louis Dr.

Warminster, PA 18974 US

Telephone

General Information

215-674-4300

Technical

Assistance

800-521-3168

Customer Service

800-272-4620

24-Hour Emergency

800-424-9300 (US)

(CHEMTREC)

703-527-3887 (International)

Website

www.crcindustries.com

2. Hazard(s) identification

Category 2Flammable aerosols

Physical hazards

Liquefied gasGases under pressure

Not classified.

Health hazards

Not classified.

Environmental hazards

Not classified.

OSHA defined hazards

Label elements

Signal word

Warning

Hazard statement

Flammable aerosol. Contains gas under pressure; may explode if heated.

Precautionary statement

Prevention

Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open

flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Use

with adequate ventilation. Open doors and windows or use other means to ensure a fresh air

supply during use and while product is drying.

Response

Wash hands after handling.

Storage

Store in a well-ventilated place. Protect from sunlight. Do not expose to temperatures exceeding

50°C/122°F. Exposure to high temperature may cause can to burst.

Disposal

Dispose of waste and residues in accordance with local authority requirements.

Hazard(s) not otherwise

classified (HNOC)

None known.

Supplemental information

When exposed to extreme heat or hot surfaces, vapors may decompose to harmful or fatal corrosive gases such as hydrogen

fluoride.

3. Composition/information on ingredients

Mixtures

1 / 8

Material name: Food Grade Mold Release WO

03311 Version #: 02 Revision date: 11-15-2016 Issue date: 02-25-2014

SDS US

Summary of content (8 pages)

PAGE 1
SAFETY DATA SHEET 1. Identification Product identifier Food Grade Mold Release WO Other means of identification Product code 03311 Recommended use Mold release lubricant Recommended restrictions None known. Manufacturer/Importer/Supplier/Distributor information Company name Address Telephone General Information Technical Assistance Customer Service 24-Hour Emergency (CHEMTREC) Website CRC Industries, Inc. 885 Louis Dr.
PAGE 2
Chemical name Common name and synonyms CAS number % dimethyl ether 115-10-6 50 - 60 1,1-difluoroethane 75-37-6 30 - 40 8042-47-5 5 - 10 white mineral oil Specific chemical identity and/or percentage of composition has been withheld as a trade secret. 4. First-aid measures Inhalation Skin contact Eye contact Ingestion If symptoms develop move victim to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention, if needed.
PAGE 3
7. Handling and storage Precautions for safe handling Conditions for safe storage, including any incompatibilities Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition.
PAGE 4
9. Physical and chemical properties Appearance Physical state Liquid. Form Aerosol. Color Clear. Odor Odorless. Odor threshold Not available. pH Not available. Melting point/freezing point Not available. Initial boiling point and boiling range 450 °F (232.2 °C) Flash point 350 °F (176.7 °C) Cleveland Open Cup Evaporation rate Moderate. Flammability (solid, gas) Not available. Upper/lower flammability or explosive limits Not available.
PAGE 5
Information on toxicological effects Acute toxicity Components Species Test Results Rat 164000 ppm, 4 Hours dimethyl ether (CAS 115-10-6) Acute Inhalation LC50 308.5 mg/l, 4 hours white mineral oil (CAS 8042-47-5) Acute Dermal LD50 Rabbit > 2000 mg/kg Inhalation LC50 Rat > 5 mg/l, 4 hours Oral LD50 Rat 50000 mg/kg * Estimates for product may be based on additional component data not shown. Prolonged skin contact may cause temporary irritation.
PAGE 6
13. Disposal considerations Disposal of waste from residues / unused products Hazardous waste code Contaminated packaging The dispensed liquid product is not a RCRA hazardous waste (See 40 CFR Part 261.20 - 261.33). Consult authorities before disposal. Contents under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container.
PAGE 7
US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance Not listed. CERCLA Hazardous Substance List (40 CFR 302.4) Not listed. CERCLA Hazardous Substances: Reportable quantity Not listed. Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Not regulated.
PAGE 8
Country(s) or region Europe Inventory name European Inventory of Existing Commercial Chemical Substances (EINECS) On inventory (yes/no)* Yes Europe European List of Notified Chemical Substances (ELINCS) Japan Inventory of Existing and New Chemical Substances (ENCS) Yes Korea Existing Chemicals List (ECL) Yes New Zealand New Zealand Inventory Yes Philippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) Yes United States & Puerto Rico Toxic Substances Control Act (TSCA)