CR-10 Series 3D Printer User Manual The User Manual is for the CR-10 Series of 3D printers. It is also applicable for the CR-10S/CR-10 S4/CR-10 S5. But CR-10 mini without T-Bracket (Right) & Decoration Strip. Due to the different types of devices ,Hardware and software upgrade. the devices have little different, it is normal phenomenon. Subject to actual device received. Detailed instructions for using are available in the TF card. V.6.
Parameters Basic Parameters Model CR-10 CR-10S CR-10 S4 CR-10 S5 CR-10mini Printing Size 300*300*400mm 300*300*400mm 400*400*400mm 500*500*500mm 300*220*300mm Molding Tech. FDM Nozzle Number 1 Slice Thickness 0.1mm-0.4mm Nozzle Diameter Standard 0.4mm Precision ±0.1mm Fliament 1.
CONTENTS Dear consumers, Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer. Our 3D team will always be ready to give you the best service. Please contact us via the phone number or e-mail address provided at the end when you encounter any problem with the Printer. For a better experience in using our product, you may learn how to use the Printer in the following ways: View the accompanied instructions and videos in the TF card.
NOTES 1. Do not use the printer any way other than described herein in order to avoid personal injury or property damage. 2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment. 3. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality. 4.
A、 Introduction Filament Holder Control Box Nozzle Assembly Connection Platform Connection Power Cable Connection Extruder (E) Stepper Z Gantry Frame Nozzle Kit X Limit Switch X Stepper TF Slot and USB Port Display Screen Control Knob Z Stepper Z Limit Switch Voltage Selection Base Frame Platform Y Limit Switch Y Stepper 1
B、General List Tool Box Base Frame Control Box Gantry Frame uTool list No. 2 Image Name Qty No. Image Name Qty No.
C、Device Installtion u Install the T-shaped fixing block. u Install the Gantry Frame Note: Make sure that the nut for pro file h a s b e e n t u r n e d b y 9 0 ° before fastening the T-shaped fixing block. M5X25 4pcs *CR-10 mini without T-Bracket (right).
◆ Install the Rack Attach the Bracket with two thumb screws. Attach Spool Holder with included Nuts Finished ◆ Install decoration strip Install decoration belt into the notch, starting from one end. Cut off the excess material with the diagonal pliers *The decoration Strip is available in various colors. The pictures above are for reference only. *CR-10mini without Decoration Strip. 4 Attach the Decorative Trim to all parts needing to be decorated.
D、Introduction Connect the Stepper Motors according to the yellow labels on the 6pin (4-wire) side. Y Stepper and Limit Switch Extruder (E) Stepper Connect the Limit Switches according to the yellow labels on the 3pin (2-wire) side. X Stepper and Limit Switch Z Stepper and Limit Switch Connect the aviation connectors to the ports with corresponding pins • • • Select the correct input voltage to match your local mains (230V or 115V) Damage can occur if voltage is set incorrectly.
E、 Screen Information Print Speed Device Model Push：OK/Enter Sub Menu Turn：Change Option/Value Set Temperature of the Nozzle Current Temperature of the Nozzle Set Temperature of the Hot Bed Current Temperature of the Hot Bed Part Cooling Fan Speed Current Location of the nozzle Print Time Print Progress Prompt Message 6
F、Loading Filament 2、Feed Filament 1、Preheat Method 1 7 Method 2 Press and hold the extruder lever then insert the1.75mm filament through the small hole of the extruder. Continue feeding until you see filament come out the nozzle. Tip：How to Replace the Filament？ 1、Cutting filament near the Extruder and slowly feed new filament until they are fed into the new filament. 2、Preheating the nozzle and withdraw the filament quickly and feed the new filament.
G、Bed Leveling 1. Prepare →Auto Home. Waiting for the nozzle to move to the left/front of the platform.→ Prepare→Disable Steppers(Close stepper drive，release motor） 4 3 1 2 2. Move the nozzle the front/left leveling screw and adjust the platform height by turning the knob underneath. Use a piece of A4 paper (standard printer paper) to assist with the adjustment, making sure that the nozzle lightly scratches the paper. 3. Complete the adjustment of the screw on all 4 corners. 4.
H、Software Installation 1. Double click to install the software. 2、Double click to open the software. 3. Select language→Next→Select your machine→Next→Finish.
I、First Printing 1.Slicing Open the software→Load→Select the file→Wait for slicing to finish ,and save the gcode file to TF card. 2.Printing Insert the TF card→ Print → Select the file to be printed.
After- Sales Service Service 1, The printer can be returned within seven days, 15 days replacement, one year warranty, lifetime maintenance. Replacement requirement 1. The appearance of the product is intact, without damage, scratches, smudges, cracks, deformation, etc.; 2. Machine parts, tools and others are complete; 3. Provide a complete and valid purchase invoice and warranty, product number should be the same.
The revision date: May 20,2019 SHENZHEN CREALITY 3D TECHNOLOGY CO.,LTD. 11F & Room 1201,Block 3,JinChengYuan,Tongsheng Community,Dal ang,Longhua District,Shenzhen,China,518109 Official Website: www.creality3d.cn Tel: +86 755-85234565 E-mail: info@creality3d.cn cs@creality3d.
