V2.
1
2
Introduction 设备简介 7 1 8 9 2 3 4 10 14 16 11 5 12 6 15 13 1 X motor X电机 5 Belt tensioning screw 皮带张紧螺丝 9 Y motor Y电机 13 Storage card slot and USB socket 存储卡槽及USB插口 2 Nozzle kit 喷头套件 6 Manual power switch 手拨电源开关 10 Material rack and material tube 料架及料管 14 Y-axis limit adjustment component Y轴限位调节组件 3 Printing platform 打印平台 7 X axis limit switch X轴限位开关 11 Knob screen 旋钮屏 15 Z axis belt motor Z轴皮带电机 4 Bed leveling nut 调平螺母 8 Extruder 挤出机 12 Knob 旋钮 16 Power cable connection 电源组合开关 3
Basic Parameters 基本参数 Model | 型号 Print size | 成型尺寸 Molding technology | 成型技术 Number of nozzle | 喷头数量 Layer thickness | 打印层厚 Nozzle diameter | 喷嘴直径 XY axis precision | 精度 Filament | 打印材料 File format | 支持格式 File transfer | 打印方式 Compatible slicing software | 可兼容切片软件 Power specification | 电源规格 Total power | 总功率 Hotbed temperature | 热床温度 Nozzle temperature | 喷嘴温度 Resume printing function | 断电续打 无限长*200*170mm（长*宽*高）| Infinite length*200*170mm (length*width*height) FDM 1 0.1mm-0.4mm Standard | 标配 0.
Parts List 零部件清单 5 Filament 耗材 x 1 4 Spool holder 料架 x 1 1 X/Y axis belt assembly x 1 X/Y轴皮带组件 2 Bottom belt assembly x 1 底部皮带组件 3 Display kit x 1 Accessory tool list 8 Storage card and card reader x 1 存储卡和读卡器 12 Blue line claw x 2 蓝色线夹 16 M5T nuts x 6 M5 T型螺母 9 Diagonal pliers x 1 剪钳 13 Pneumatic connector x 2 气动接头 Photoelectric switch line x 1 17 光电开关线 20 Hexagon socket flat round head screw M5X18 x 10 内六角平圆头螺钉M5X18 21 24 Nozzles x 2 喷嘴 25 Hexagon socket head spring washer combination s
1 Install the Profile Support Frame 安装型材支撑架 6 7 2 Bottom belt assembly x 1 底部皮带组件 Profile bracket 1 x 1 型材支架1 6 7 19 6 Profile bracket 2 x 1 型材支架2 Hexagon socket flat round head screw M5X12 x 4 内六角平圆头螺钉M5X12 19 2 19 Step: Install the profile support 1 and profile support 2 to the bottom of machine with four hexagon flat head screws M5x12 (As shown in the figure above).
2 Install X/Y Axis Belt Assembly 安装X/Y轴皮带组件 21 21 20 1 1 X/Y axis belt assembly x 1 X/Y轴皮带组件 20 20 20 Install with M5 * 45 socket head cap screws with spring washer.
3 Install the Spool Holder 安装料架 4 Spool holder料架 x 1 4 16 M5T nuts M5 T型螺母 x 2 18 18 Hexagon socket flat round head screw M5X8 x 2 内六角平圆头螺钉M5X8 8 16
4 Install the Display 安装显示屏 16 M5T nuts M5 T型螺母 x 2 18 18 18 Hexagon socket flat round head screw M5X8 x 2 内六角平圆头螺钉M5X8 16 16 Step: Lock the display assembly with two M5X8 flat head screws and two M5 T-nuts, as shown in the figure above; 步骤：用2颗M5x8的平圆头螺丝跟2颗M5 T型螺母将显示屏组件锁住，如上图示； 9
5 Cable Connection 设备接线 14 Power cord x 1 电源线 After the display is installed, please connect the display cable. 显示屏安装完成后，请将显示屏线连接好。 Insert the Teflon tube into the pneumatic connector (also insert the blue wire clamp) 将铁氟龙管插入气动接头（同时插入蓝 色线夹） Connect the Y-axis limit line. 连接Y轴限位线。 Connect the broken detection line as shown in Figure A . I 按图示A连 接断料检测线。 A Caution ●Select the correct input voltage match your local power. (115/230V) ●Damage can occur if voltage is set incorrectly.
6 Leveling 调平 1.First move the X axis to the contact part between the nozzle and the belt (slightly press the nozzle onto the belt ) . 2.Push the two limit switches against the X sliding block to lock the limit; 3.
7 12
13
8 14
9 When the current temperature reaches the target temperature, press and hold the spring of the extruder and insert the consumables into the charging detection hole one by one， then insert the consumables into the small hole of the extruder until the nozzle position.
10 3. Select language→close→setting→add corresponding model→printer setting→close→customize→ confi guration→number of prints to complete the setting. CrealityBelt 16 CrealityBelt 3.
10 4. Open the file in turn → select the file. 依次打开文件→选择文件。 6.Insert the storage card→ print from card→select the file to be printed. 插入存储卡→从存储卡上打印→选择要 打印的文件。 5.Generate G-code, and save the gcode file to storage card. 生成G代码→保存到存储卡。 File names must be Latin letters or numbers, not Chinese characters or other special symbols.
X-axis motor port X轴电机接口 Y-axis motor port Y轴电机接口 Z-axis motor port Z轴电机接口 E-axis motor port Storage card slot E轴电机接口 存储卡卡槽 Micro USB port Micro USB接口 Nozzle fan 喷头风扇 12864 screen 12864屏幕 Motherboard fan 主板风扇 Power input 电源输入 18 Hot bed wire port 热床线接口 Heating pipe interface 加热管接口 Controllable nozzle fan 喷头可控风扇 X axis limit switch X轴限位开关 Hot bed thermal 热床热敏 Nozzle thermistor 喷头热敏 Broken material detection 断料检测 Y axis limit Y轴限位
Trouble-Shooting Workflow Fault diagnosis Fault cause N Start Play by memory card Seal Y/N Y N N File identification or not Y Display error codes or not Return “Home” Y/N Y Y N Y Print or not Y N Beyond “Home” Y Hot bed is heated or not Y The display of temp is normal or not N N N Printing when The nozzle is heated or not Y Dislocation or not filament-push N Filament-push or not Finish N The E motor rotates or not N The display of humidity is normal or not N Y Y Y/N Y
工作流程 故障诊断 开始 由存储卡打 印 是／否 是 否 否 文件是否 识别 是 回零 是／否 是 是 否 是否运动 是 是 否 是 完成 热床是否 加热 是 否 喷嘴是否 加热 是 是否错位 否 是 否 E电机是否 是 转动 文件名 １．文件名修改为英文和数字格式 切片 热床 温度是否 正常 热敏电阻 否 加热管 温度显示 是否正常 热敏电阻 否 是 切片/同步带 联轴器 否 挤出齿轮 是否转动 １．擦拭存储卡 ２.格式化存储卡 ３.更换存储卡 限位开关 是 是否出料 否 是 是 耗材是否 正常 故障处理 存储卡 轴电机 越过零点 否 20 其他文件是否 打印正常 否 出丝打印 是／否 是 否 喷嘴加热 是／否 是否乱码 否 热床加热 是／否 故障原因 否 是 其他 否 耗材 E电机 结果反馈 １．移动模型位置并重新切片 ２.使用修复软件修复模型 １．检查电机、线路 ２.用替换法检查 １．检查限位开关、线路 ２.
11F & Room 1201, Block 3, JinChengYuan, Tongsheng Community, Dalang, Longhua District, Shenzhen, China, 518109 Official Website: www.creality.com Tel: +86 755-8523 4565 E-mail: info@creality.com cs@creality.
