SKY VIEW GYM Model: 3101
Creative Cedar Designs 8
STOP…PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT www.creativecedardesigns.com OR CONTACT US DIRECTLY AT OUR OFFICE, 1-888-363-4967 WE WILL ANSWER YOUR QUESTIONS, OR HELP WITH WHAT YOU NEED. For more efficient service, please log onto our website at www.creativecedardesigns.com and fill out a request for missing or damaged parts. A completed product registration is also necessary for all warranty claims.
Dear Customer: Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable fun. Creative Cedar Designs equipment is recommended for use by children 3 to 10 years of age. Creative Cedar Designs structures are not intended for public use. Creative Cedar Designs does not warranty any of its residential structures subjected to commercial use.
The instructions and owner’s manual for your new Playcenter should be read in its entirety before assembly, to minimize problems and safety issues. We recommend reading the owner’s manual thoroughly after you have identified all of the parts for your Playcenter as discussed in the Helpful Installations Hints section below. Positioning Your Play center 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper.
Helpful Installation Hints 1. Depending on your experience, assembly of this Play set should take approximately 6 to 12 hours after inventory of parts. Therefore, we recommend you set aside a full day for assembly. 2. Identify all of the parts for your Playcenter. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. 3.
Suggested Playground Surfacing Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing materials after assembly. If used properly these materials can absorb some of the impact of a child’s fall. All surface material should extend a minimum of 6 feet in all directions around the play area.
Operating Instructions: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1. This Playcenter is designed for the use of 4 occupants not exceeding 290 pounds. 2. On-site adult supervision is required. 3. Instruct children not to walk close to, in front of, behind, or between moving swings or other moving playground equipment. 4.
Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) We recommend you check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. 2. Remove plastic swing seats and take indoors or do not use when the temperature drops below 32 F. 3.
APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material Also see the following website for additional information: https://www.cpsc.gov/PageFiles/122146/324.pdf . X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS11 X3.1 The U.S.
SKY VIEW GYM SET Assembly Instructions WARNING: CHOKING HAZARD Unassembled parts may be a choking hazard to children 3 years and younger CAUTION: Adult Assembly Required. Hardware contains small pieces with sharp points. Keep parts out of the reach of children until assembled. Parts of this product can present dangers ifi mproperly assembled. 9 CAUTION: The plastic bags that contain the hardware may present a choking hazard to small children.
Basic Setup Dimensions Place the set on level ground, not less than 6ft (1.83M) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. 29'-10" [9,4M] 17'-10" [5,4M] 9'-4" [2,8M] 21'-4" [6,8M] Ht. = 9'-9" [3M] SAFE HEIGHT Ht. = 15'-9" [5M] Important Assembly Notes 1) While assembling unit, take time before and after each phase to make sure Fort is level. If fort is not level, assembly will be difficult and improper assembly may result.
Parts Identification Wood Components (1) 3 5/16 X 5 5/16 X 89 1/2 SWING BEAM - LA251 (3) 11/16 X 3 1/2 X 22 ROCKWALL ROCK BRD.
Parts Identification Wood Components (2) 1 X 3 1/2 X 69 TARP UPRIGHT - WC003-10 (1) 2 X 2 11/16 X 54 ROCKWALL RAIL-RIGHT - WSF001-10 (1) 1 X 3 1/2 X 54 3/8 LADDER RAIL-LEFT - WC004-10 (1) 1 X 3 1/2 X 54 3/8 LADDER RAIL-RIGHT - WC005-10 (1) 2 X 2 11/16 X 54 ROCKWALL RAIL-LEFT - WSF002-10 (4) 1 X 3 1/2 X 20 LADDER STEP - WC006-10 (2) 1 X 3 1/2 X 35 TABLE LEG - WC007-10 (2) 1 X 3 1/2 X 17 TABLE BRACE - WC008-10 (2) 1 X 3 1/2 X 10 TABLE BRACE - WC009-10 (1) 1 X 5 1/2 X 54 SWING BEAM CROSS BRACE - WD001
Parts Identification Accessories (2) GLIDER SUPPORT ASSEMBLY - A500 (2) GREEN ANGLE BRACKET (5") - M005 (13) GREEN L-BRACKET (SMALL) - M002 (2) FORT TARP (GREEN) - P3101 (4) SWING HANGER - M020 (8 COUNT BAG) CLIMBING ROCKS - B8LGR (2 - PAIR) HAND GRIP - P002 (2) 4 HOLE TRIANGLE PLATE - M105 (6) - PLASTIC- P004 (1) - GLIDER SEAT- P202 (2) GLIDER ARM - P201 8' WAVE SLIDE (GREEN) - P401 (2) - SWING SEATS w/ CHAIN - A100 13
Hardware Identification 5/16" x 6" Hex Bolts 5/16HB6 (2) 5/16" x 5 3/4" Hex Bolts (8) 0 1/4" 5/16" x 4" Hex Bolts 5/16HB4 1/2" (8) 3/4" 1" 5/16" x 2 1/2" Hex Bolts 5/16HB21/2 (10) 5/16" x 2 1/4" Hex Bolts 2" 5/16HB21/4 1" Tapping Screws (12) #14TS1 (16) 5/16" x 2" Hex Bolts 5/16HB2 3" (6) 3/4" Tapping Screws #14TS3/4 (24) 5/16" x 1 1/4" Hex Bolts (4) 5/16HB11/4 4" 5/16" x 1 1/4" Machine Truss Screw 5/16" x 3 1/2" Lag Screws (8) 5/16MT11/4 5/16LS31/2 5" (2) 5/16" x 2" Lag Scre
Hardware Identification 2 1/2" Deck Screws 1/4" T-nuts #8DS2 1/2 (10) (22) 2" Deck Screws #8DS2 1/4TN 1/4" Split Washers (32) 1/4SW (10) 1 1/2" Deck Screws #8DS11/2 (112) 1/4 x 1 1/4" Machine Truss 1/4MT11/4 1 1/4" Deck Screws (10) #8DS11/4 (83) 1/4" Flat Washers 1/4FW 3/4" Deck Screws (18) #8DS3/4 (2) Fender Washer 5/16" T-nuts 5/16" Split Washers 5/16SW (40) 5/16FW8X27 5/16" Lock Nuts 5/16TN LN5/16 (40) (21) (111) 5/16" x 4 1/2" Slotted Pan-Head Screw 5/16PH41/2 5/16" Flat
Phase Hardware Phase 1: FORT FRAME ASSEMBLY 5/16" x 2 1/4" Hex Bolts (8) Fender Washer 5/16" Split Washers (12) (12) 5/16" x 2 1/2" Hex Bolts BUILD 2 FRAME ASSEMBLIES 5/16" T-nuts (4) (12) Phase Parts (2) 11/16 X 5 1/2 X 54 GROUND BOARD - WB001-10 (2) 1 X 3 1/2 X 54 FLOOR BRD.
Phase Hardware Phase 2: FORT FRAME ASSEMBLY Fender Washer 5/16" x 2" Lag Screws (12) (12) Phase Parts (2) 11/16 X 3 1/2 X 35 1/2 FLOOR SUPPORT - WA001-10 (2) 11/16 X 5 1/2 X 35 1/2 GROUND BOARD - WB003-10 Note: It is IMPORTANT that the fort be level after this phase! 35 1/2 O.D. FLUSH 35 1/2 O.D.
Phase Hardware Phase 3: FLOOR INSTALLATION 1 1/2" Deck Screws (34) 3/4" Tapping Screws 1 1/4" Deck Screws (4) (17) Phase Parts (13) 11/16 X 3 1/2 X 37 1/2 FLOOR BOARD - WA002-10 (2) 11/16 X 5 1/2 X 32 3/4 END FLOOR BRD.
Phase 4: Phase Hardware RAIL ATTACHMENT Fender Washer 5/16" x 2 1/2" Hex Bolts (2) 5/16" Split Washers (8) (2) 5/16" x 2" Lag Screws 5/16" T-nuts (2) (6) USE A STEP LADDER FOR SAFETY! Phase Parts (1) 1 X 5 1/2 X 54 SWING BEAM CROSS BRACE - WD001-10 (2) 11/16 X 3 1/2 X 54 WALL RAIL - WA006-10 13 8 BOLT CROSS BRACE THROUGH 2ND HOLE FROM THE TOP OF THE UPRIGHT MAKE SURE THE 1 3/8" GAP IS TO THE BOTTOM OF THE CROSS BRACE FOR CORRECT INSTALLATION T-NUT 2 1/2" HEX BOLT SPLIT WASHER & FENDER WASHER
Phase 5: DECK LADDER ASSEMBLY Phase Hardware 2" Deck Screws 2 1/2" Deck Screws (4) (16) Phase Parts (1) 1 X 3 1/2 X 54 3/8 LADDER RAIL-LEFT - WC004-10 (4) 1 X 3 1/2 X 20 LADDER STEP - WC006-10 (1) 1 X 3 1/2 X 54 3/8 LADDER RAIL-RIGHT - WC005-10 (1) 11/16 X 3 1/2 X 21 1/4 SAFETY / TABLE SLAT - WA014-10 WC004-10 2 1/2" DECK SCREWS WC006-10 WC005-10 WA014-10 1 214 2 21" 20
Phase 6: Phase Hardware ROCKWALL ASSEMBLY 5/16" x 1 1/4" Machine Truss Screw 1 1/2" Deck Screws (8) (60) 1" Tapping Screws (8) 5/16" Split Washers (8) 1/4" Flat Washers (8) 5/16" T-nuts (8) Phase Parts (1) 2 X 2 11/16 X 54 ROCKWALL RAIL-RIGHT - WSF001-10 (5) 11/16 X 3 1/2 X 22 ROCKWALL ROCK BRD. - WA010-10 (3) 11/16 X 3 1/2 X 22 ROCKWALL ROCK BRD.
Phase 7: ROCKWALL & LADDER ATTACHMENT Phase Hardware 1" Tapping Screws (4) 3/4" Tapping Screws (4) Phase Parts FLOOR (4) GREEN L-BRACKET (SMALL) - M002 FLR. SUP.
Phase 8: TOP RAIL INSTALLATION Phase Hardware 5/16" x 2" Lag Screws Fender Washer 5/16" x 2 1/4" Hex Bolts (18) (14) 5/16" Split Washers (4) 5/16" T-nuts (4) (4) Phase Parts (1) 11/16 X 5 1/2 X 54 RAIL/GROUND BOARD - WB001-10 (2) 11/16 X 5 1/2 X 35 1/2 CENTER ARCH RAIL - WB004-10 (1) 11/16 X 3 1/2 X 54 WALL RAIL - WA006-10 (1) 11/16 X 5 1/2 X 54 SIDE ARCH RAIL - WB002-10 TOP WALL RAILS ARE FLUSH WITH EACH OTHER WA006-10 * 2 1/2" BETWEEN BOARDS T-NUTS WB001-10 (ATTACH THIS RAIL FIRST, THEN ALI
Phase 9: TARP BRACE INSTALLATION Phase Hardware 5/16" x 2 1/2" Hex Bolts Fender Washer 5/16" Split Washers (4) (6) (6) 5/16" x 2" Hex Bolts 5/16" T-nuts 1 1/2" Deck Screws (2) (2) (6) Phase Parts (2) 1 X 3 1/2 X 80 TARP CROSS BRACE - WC002-10 2 1/2" HEX BOLT SPLIT WASHER & FENDER WASHER T-NUTS (2) 1 X 3 1/2 X 69 TARP UPRIGHT - WC003-10 90° 90° T-NUTS 2 1/2" HEX BOLT SPLIT WASHER & FENDER WASHER 90° 24
Phase 10: LOWER RAIL ATTACHMENT Phase Hardware 5/16" x 2" Lag Screws Fender Washer (5) 1 1/4" Deck Screws (14) (5) Phase Parts (2) 11/16 X 3 1/2 X 15 1/2 SANDBOX SEAT - WA016-10 (1) 11/16 X 3 1/2 X 28 3/4 WALL RAIL - WA007-10 (2) 11/16 X 3 1/2 X 8 1/2 SANDBOX SEAT - WA015-10 (2) 11/16 X 3 1/2 X 22 1/2 SANDBOX SEAT - WA017-10 (4) 11/16 X 3 1/2 X 6 1/2 WALL RAIL - WA008-10 TARP UPRIGHT 2" LAG SCREW & FENDER WASHER !!END WALL OPENINGS!! WA008-10 (REST RAIL ON FLOOR AND LAG SCREW INTO CENTER OF UPRI
WALL SLAT ATTACHMENT Phase 11: Phase Hardware 3/4" Tapping Screws 1 1/4" Deck Screws (10) (52) Phase Parts WALL SLAT (13) 11/16 X 3 1/2 X 27 WALL SLAT - WA009-10 2" L-BRACKET 3/4" TAPPING SCREW FLOOR (5) GREEN L-BRACKET (SMALL) - M002 L-BRACKET DETAIL E SI D SI D 2 FLUSH L-BRKT.
Phase 12: TARP SUPPORTS LUNCH TABLE UPRIGHT Phase Hardware 1 1/2" Deck Screws (16) Phase Parts (2) 11/16 X 3 1/2 X 37 1/2 TARP SUPPORT - WA003-10 (1) 1 3/8 X 3 3/8 X 46 1/4 TABLE UPRIGHT - WE002-10 (1) 11/16 X 3 1/2 X 35 1/2 TARP SUPPORT - WA004-10 WA004-10 DECK SCREWS WA003-10 90° WE002-10 21 1/4" I.D. FIT UNDER FLOOR ATTACH THROUGH GROUND BOARD INTO 'WE002-10' 1 I.D. 214 90° 1 I.D.
Phase 13: HAND GRIP ATTACHMENT Phase Hardware 1/4 x 1 1/4" Machine Truss 1/4" Flat Washers (8) (8) 1/4" Split Washers (8) 1/4" T-nuts (8) Phase Parts (2 - PAIR) HAND GRIP - P002 1/4" X 1 1/4" MACHINE TRUSS SCREW 1/4" SPLIT WASHER 1/4" FLAT WASHER 1/4" T-NUT SLAT CENTER GRIP ON SLAT SHOWN USE 5/16" DRILL BIT DRILL THROUGH SLAT USING HAND GRIP AS A GUIDE 28
Phase 14: SWING BEAM ASSEMBLY Phase Hardware Fender Washer 5/16" Flat Washers 5/16" x 4 1/2" Slotted Pan-Head Screw 5/16" Lock Nuts (1) (18) (9) 5/16" x 3 1/4" Slotted Pan-Head Screw 5/16" x 3 1/2" Lag Screws (2) (2) (2) 5/16" x 4" Hex Bolts (6) Phase Parts (1) 3 5/16 X 5 5/16 X 89 1/2 SWING BEAM - LA251 (2) 1 3/8 X 3 5/16 X 82 1/2 SWING ANGLE BRACE - LG252 (1) 1 3/8 X 3 5/16 X 89 SWING GROUND BOARD - LG253 (1) 3 5/16 X 2 11/16 X 83 SWING END BEAM - LD254 (2) 105° TRIANGLE PLATE - M105 (2)
Phase 15: SWING BEAM ASSEMBLY Phase Hardware Fender Washer 5/16" Lock Nuts 5/16" x 6" Hex Bolts (2) (12) 5/16" x 5 3/4" Hex Bolts (8) (24) 5/16" x 4" Hex Bolts (2) Phase Parts (2) GLIDER SUPPORT ASSEMBLY - A500 (1) - Glider Seat - P202 (2) GLIDER ARM - P201 (4) SWING HANGER - M020 (2) - Swing Seats w/chain - A100 STEP 1: CHAIN NOT SHOWN FOR CLARITY FENDER WASHER & LOCK NUT 6" HEX BOLT & FENDER WASHER STEP 2: 5 3/4" HEX BOLT & FENDER WASHER FENDER WASHER & LOCK NUT FENDER WASHER & LOCK NUT TI
Phase 16: SWING BEAM ATTACHMENT Phase Hardware 5/16" x 1 1/4" Hex Bolts (4) 5/16" Split Washers (4) Fender Washer (4) 5/16" T-nuts (4) HAMMER T-NUTS INTO HOLES ON BACKSIDE OF CROSS BRACE 31
Phase 17: Phase Hardware TARP ATTACHMENT 3/4" Tapping Screws (6) Phase Parts (2) FORT TARP (GREEN) - P3101 STRETCH TARP TIGHT OVER SUPPORTS 3/4" TAPPING SCREWS 3 EACH END tant I mpor ! N ote INSIDE VIEW DO NOT OVER TIGHTEN TAPPING SCREWS! TARP 3/4" TAPPING SCREWS 32
Phase 18: Phase Hardware TABLE RAILS 1" Tapping Screws (4) Phase Parts (2) 1 X 3 1/2 X 35 TABLE LEG - WC007-10 (2) GREEN L-BRACKET (SMALL) - M002 FLUSH WITH INSIDE OF UPRIGHTS 21 1/4" I.D.
Phase 19: Phase Hardware TABLE ASSEMBLY 5/16" x 2" Hex Bolts (4) Fender Washer 5/16" Split Washers (4) (4) 2" Deck Screws 5/16" T-nuts (28) (4) Phase Parts (2) 1 X 3 1/2 X 17 TABLE BRACE - WC008-10 (2) 1 X 3 1/2 X 10 TABLE BRACE - WC009-10 (5) 11/16 X 3 1/2 X 21 1/4 SAFETY / TABLE SLAT - WA014-10 2" DECK SCREWS (THROUGH BRACE INTO UPRIGHT EDGE) MAKE SURE BRACES ARE LEVEL WC009-10 WC008-10 T-NUTS 2" HEX BOLT SPLIT WASHER & FENDER WASHER 34
Phase 20: SLIDE ATTACHMENT Phase Hardware 1/4" x 1 1/4" Machine Truss (2) 1/4" Flat Washers (2) 1/4" Split Washers (2) (2) 1/4" T-nuts Phase Parts STEP 2: 8' WAVE SLIDE (GREEN) - P401 1/4" X 1 1/4" MACHINE TRUSS SCREW 1/4" SPLIT WASHER 1/4" FLAT WASHER SLIDE FLOOR SLIDE 1/4" T-NUT SLIDE HARDWARE DETAIL FLOOR JOIST 35
Phase 21: Phase Hardware ANCHORING 2 1/2" Deck Screws (6) Phase Parts (6) - Plastic Stakes - P004 STAKE STAKE Upright STAKE STAKE 2 1/2" Deck Screw Ground Board STAKE STAKE Note: Failure to use stakes can void warranty & cause injury. Final Step: Double check and make sure every bolt, screw and nut is tight. Make sure every board is secure. Make sure the fort is level and enjoy your playset.
LIMITED WARRANTY Creative Cedar Design (CCD) offers many fun, interactive, and safe play sets. We only guarantee the original purchaser that this product is free of defects for 30 days from the date of purchase. The product registration card, along with a dated purchase receipt, must be returned to CCD within 30 days. Within a 30 day period, CCD will repair or replace, at our option, defective merchandise free of charge, provided that the defective part is a manufacturer’s defect and not seasonal check.
Warranty claim procedure If you are confident that your play system has been installed and maintained properly, and you have a warranty claim, proceed with the following steps: 1. We will need copy of your proof of purchase (Vendor sales receipt only.) 2. We require a brief written description of the warranty issue. 3. Photos of warranted parts and of the entire play system. If any of the above steps are not completed, there may be delays in the completion of your claim, or possibly warranty cancellation.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. Or register at www.creativecedardesigns.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. FOLD HERE Place Stamp Here Creative Cedar Designs 2700 Riverside Dr.
