Owner's Manual And Assembly Instructions For FSC certified products look for the FSC label SGS-COC-005310 1996 Forest Stewardship Council A.C.
Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable backyard fun.
STOP…PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT www.creativecedardesigns.com OR CONTACT US DIRECTLY AT OUR OFFICE, 1-888-363-4967. WE WILL ANSWER YOUR QUESTIONS, OR HELP WITH WHAT YOU NEED. For more efficient service, please log onto our websites at www.creativecedardesigns.com and fill out a request for missing or damaged parts. A completed product registration is also necessary for all warranty claims.
Dear Customer: Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable fun. Creative Cedar Designs equipment is recommended for use by children 3 to 10 years of age. Creative Cedar Designs structures are not intended for public use. Creative Cedar Designs does not warranty any of its residential structures subjected to commercial use.
The instructions and owner’s manual for your new Playcenter should be read in its entirety before assembly, to minimize problems and safety issues. We recommend reading the owner’s manual thoroughly after you have identified all of the parts for your Playcenter as discussed in the Helpful Installations Hints section below. Positioning Your Play center 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper.
Helpful Installation Hints 1. Depending on your experience, assembly of this Play set should take approximately 6 to 12 hours after inventory of parts. Therefore, we recommend you set aside a full day for assembly. 2. Identify all of the parts for your Playcenter. Empty each box and lay out boards so you can see each part. Your instruction book will have detailed drawings that will make it easy for you to recognize individual parts. Keep all hardware and metal parts separate from wooden pieces. 3.
Suggested Playground Surfacing Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing materials after assembly. If used properly these materials can absorb some of the impact of a child’s fall. All surface material should extend a minimum of 6 feet in all directions around the play area.
Operating Instructions: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1. This Playcenter is designed for the use of 6 occupants, who have a combined weight not exceeding 420 pounds, 4 occupants on the swing area, who have a combinedweight of 350 pounds , for a total unit cpacity of 10 occupants who who have a combined total weight of 770 pounds.
Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) We recommend you check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. 2. Remove plastic swing seats and take indoors or do not use when the temperature drops below 32 F. 3.
APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material Also see the following website for additional information: https://www.cpsc.gov/PageFiles/122146/324.pdf .
Woodlands Gymset Assembly Instructions WARNING: CHOKING HAZARD Unassembled parts may be a choking hazard to children 3 years and younger. CAUTION: Adult Assembly Required. Hardware contains small pieces with sharp points. Keep parts out of the reach of children until assembled. Parts of this product can present dangers i mproperly assembled. CAUTION: The plastic bags that contain the hardware may present a choking hazard to small children.
(14) (2) WD115 - Wall Rail - 11/16 X 3 1/2 X 5 1/2
(2) WD139 - Wall Rail - 11/16 X 3 1/2 X 33
(2) 100º TRIANGLE PLATE - M100 (1) LARGE FORT TARP (GREEN) - PT015 (6) GREENL-BRACKET-M003 (2) GREEN ANGLE BRACKET (5’’) - M005 (1) SMALL FORT TARP (GREEN) - P016 (2) 4 COUNT BAGS CLIMBING ROCKS BP011-GYBR w/ HARDWARE CreativeCedarDesigns.
(6) 1 1/4” Deck Screws #6DS1 1/4 a2a.
(6) (10) Lock Washer (122) i5.
Quick Overview of Parts RIGHT WD119 WD118 WD117 WD116 WF108 WF109 WD128 WD126 WD127 WD125 WD123 WD124 WE111 WD127 WD122 WD121 WQ120 WD103 WQ101 WD104 WQ102 FRONT 16
Quick Overview of Parts LEFT WD106 WF129 WS135 WC113 WC113 WD110 WE112 WQ136 WD139 WQ137 WD134 WC132 WD105 WD107 WF133 WD131 WD138 WD130 BACK 17
i5 *Lay out both WQ101 as illustrated. *Attach three WD121 into the pre-drilled holes with bolts “d4” and then secure with screw “c3” *Attach three WF109 into the pre-drilled holes with bolts “d4” and then secure with screw “c3” *Attach WD116 into the pre-drilled holes with bolts “d4” *Turn the wall over and attach WD105 into the predrilled holes with bolts “d5a” i5 i5 d5a i5 i5 d5a d5a.(2) i5 i5.
*Lay out both WQ102 as illustrated.
i5 i5 i5 i5 30-3/4’’ 28-1/4’’ i5.
*Attach two WD115 and two WD3139-11 into the pre-drilled holes bolts “d6” *Attach both WD107 with screws “c3” i5 i5 i5 WD139 (2) WD107 - Tower Rail - 11/16 X 3 1/2 X 31 1/2 (2) WD115 - Wall Rail - 11/16 X 3 1/2 X 5 1/2 (2) WD3139-11 - Wall Rail - 11/16 X 3 1/2 X 33 i5.
T-nuts i5 i5 i5.
(2) T-Nuts e2 e2 (2) 1-1/4’’ Hex Head Bolts for small rocks (2) 1-1/2’’ Hex Head Bolts for large rocks (1) Flat Washer per bolt (1) Lock Washer per bolt e2 *Line up each rock with the one hole & mark the second hole. Drill 3/8" hole at location then mount as shown above. *Make certain all hardware is fully secured. e2. (2) (2) 4 COUNT BAGS CLIMBING ROCKS BP011-GYBR PLEASE REFER TO ACCESSORY PLAN FOR INSTALLATION INSTRUCTIONS AND HARDWARE.
i5 i5.
i5 a2a a2a T-nuts (2) (4) a2a. (2) i5.
*Pre-drill holes with a 1/8” drill bit *Install all safety handles as shown. 1-3/4’’ Wood Screw & Flat Washer 1/8’’ Pilot Hole Safety Handle 8” (1 - PAIR) Safety Handles BP007-Y 1-3/4’’ Wood Screw & Flat Washer PLEASE REFER TO ACCESSORY PLAN FOR INSTALLATION INSTRUCTIONS AND HARDWARE.
*Pre-drill 1/8 Pilot Holes It is flush to the inside edge of the uprights, not to the outer edge.
*Lay out both WQ120 *Attach the WD121 on the bottom with bolts d4 and then secure with screws c3 *Attach WD123 on top with bolts d4 *Turn the wall over and attach the remaining two WD121 with bolts d4 and then secure with screws c3 i5 i5 i5 i5.
c3 i3 i5 2 (6) i3. (6) i5.
*Create the small tarp support frame by attaching WD128 and WD126 with screws a3. *Insert T-Nut as shown. *Attach WD125 to WD123 as shown with screw a2a and hex head bolt d3. *Attach the pre-assembled frame to WD125 with screws a3 and screws a2a. * Note: WD128 will overhang WD125 by 5/8’’. WD123 i5 a2a a2a Note: WD 128 will overhang WD125 by 5/8’’ a2a a3. (7) a2a. (7) (1) i5.
* Lay the small tarp over the small tarp support. * Make sure the tarp is centered and pulled taught before securing with screws and washers on the outside of the brace. Attach Tarp Screws and washers in these locations. END OF TARP VIEW 1-1/4 FROM BOTTOM PT016 TARP SCREWS PLEASE REFER TO THE HARDWARE INCLUDED WITH YOUR TARP.
Attach Tarp Screws and washers in these locations. * Lay the large tarp over the large tarp support. * Make sure the tarp is centered and pulled taught before securing with screws and washers on the outside of the brace. 5/8 tapping screw & washers 3 total (each side) PT015 PLEASE REFER TO THE HARDWARE INCLUDED WITH YOUR TARP.
(3) 1" Truss Head Screws (3) 1" Truss Head Screws
T-nuts a NOTE: High edge of WQ136 goes towards the inside of the swing assembly i5 d5a i5 d5a i5 d5a i5.
STEP 1: Follow Swing Hanger install. STEP 2: Follow Swing Seat install. STEP 3: Follow Ring-Trap install. RING-TRAP INSTALLATION * Attach Quick Links to chain as shown in (1). * Attach Quick Links to Rings as shown in (2). * * Attach Trapeze Bar as shown. * Tighten all Quick Links fully closed with a suitable wrench, as shown. * Hang one chain from each swing hanger.
i5 CENTER AND ATTACH PLACARD WITH 3/4" DECK SCREWS CreativeCedarDesigns.com (1) NAME PLATE w/ HARDWARE i5.
FLAT WASHER 1-1/2’’ LAG BOLT METAL STRAP ANCHOR (4) Anchor (4) Anchor Strap (4) 1-1/2’’ LAG BOLT BP001-B (4) FLAT WASHER
LIMITED WARRANTY Creative Cedar Design (CCD) offers many fun, interactive, and safe play sets. We only guarantee the original purchaser that this product is free of defects for 30 days from the date of purchase. The product registration card, along with a dated purchase receipt, must be returned to CCD within 30 days. Within a 30 day period, CCD will repair or replace, at our option, defective merchandise free of charge, provided that the defective part is a manufacturer’s defect and not seasonal check.
Warranty claim procedure If you are confident that your play system has been installed and maintained properly, and you have a warranty claim, proceed with the following steps: 1. We will need copy of your proof of purchase (Vendor sales receipt only.) 2. We require a brief written description of the warranty issue. 3. Photos of warranted parts and of the entire play system. If any of the above steps are not completed, there may be delays in the completion of your claim, or possibly warranty cancellation.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. Or register at www.creativecedardesigns.
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. FOLD HERE Place Stamp Here Creative Cedar Designs 2700 Riverside Dr.