Use and Care Manual

ManualsBrandsCreative Cedar Designs ManualsPlayground SetsCedar Chalet Complete Wood Playset with Wooden Roof, Climbing Wall, Sandbox, Slide and Multiple Swing Set Accessories

ASSEMBLY INSTRUCTIONS

Creative Cedar Designs • PO Box 4901 • Chattanooga, TN 37405

Visit our web site at: www.Creativecedardesigns.com or call us at 888-363-4967

Cedar Chalet

3710

Summary of content (32 pages)

PAGE 1
Cedar Chalet 3710 ASSEMBLY INSTRUCTIONS Creative Cedar Designs • PO Box 4901 • Chattanooga, TN 37405 Visit our web site at: www.Creativecedardesigns.
PAGE 2
ATTENTION: READ THIS BEFORE USE OF YOUR PLAYSET OR ACCESSORY: Observing the following statements and warnings reduces the likelihood of serious or fatal injury. This product has been designed for single family home/residential use only and is not intended for use in any public setting. Placement in public settings constitutes misuse of this product. Play Safe Installation Checklist: → No children are to be allowed to use the equipment until it is properly installed.
PAGE 3
SAFE USE ZONE THE MINIMUM USE ZONE FOR THE PLAYSET SHALL EXTEND NO LESS THAN 72” FROM ALL SIDES OF THE UNIT. SWING USE ZONE EXTENDS NO LESS THAN 163” EACH SIDE OF THE SWING BEAM. NO OBSTRUCTIONS, (POLES, TREES, STRUCTURES,) CAN BE INSIDE THE USE ZONE. 28’ 30’ 9’ 2-1/2’’ 8’’ Minimal Clearance Between Swings and Ground.
PAGE 4
TOOLS REQUIRED DRILL 7/16” & 1/2” SOCKET & WRENCH HAMMER ADJUSTABLE WRENCH TAPE MEASURE SQUARE DRIVE BIT PHILLIPS BIT CARPENTER SQUARE SAFETY GLASSES 5/16” DRILL BIT Important Assembly Notes 1) While assembling unit, take time before and after each phase to make sure Fort is level. If fort is not level, assembly will be difficult and improper assembly may result. Extra care must be taken to assure the fort is square on the phases that include this symbol in Fig i.
PAGE 5
INCLUDED PARTS CreativeCedarDesigns.
PAGE 6
BOARD LIST (12) WM 112 - Deck Board - 5/8’’ x 3 1/2’’ x 30’’ (2) WM 146 - Deck Board - 5/8’’ x 3 1/2’’ x 25 7/8’’ (1) WM 159 - Slide Support Board - 5/8’’ x 2’’ x 22’’ (1) WM 123 - Swing Beam Mount Board - 1 3/8’’ x 5 3/8’’ x 32 1/2’’ (2) WM 101 - Base Board - 1’’ x 5 1/8’’ x 108 1/4’’ (1) WS 135 - Swing Beam - 2’’ x 5 3/8’’ x 89 1/2’’ (1) WQ 136 - A-Frame Base- 2’’ x 3 3/8’’ x 83’’ (1) WM 110 - Bottom Barrier Support Board - 1’’ x 5 1/8’’ x 64’’ (2) WQ 137 - A-Frame Sides - 1 3/8’’ x 3 3/8’’ x 82-1/2
PAGE 7
INCLUDED HARDWARE 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer d5a. (8) 5/16" Lock Washer i5.
PAGE 8
STEP 1 X2 WM 132 WM 131-1 WM 131 WM 130 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) X2 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer d5a.
PAGE 9
STEP 2 Insert (2) 5/16’’ T-Nuts WM 156 WM 143 WM 144 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 4 1/4" Hex Head Bolt (1) T-Nut 5/16" x 2 3/4" Hex Head Bolt f1. (26) Lock Washer 5/16" x 3" Hex Head Bolt 4) Flat Washer 5/16" x 2 1/4" Hex Head Bolt d5a. (8) 5/16" x 2 3/4" Hex Head Bolt Hex Head Bolt (3) 26) 5/16" x 2 1/4" Hex Head Bolt (8) Head Bolt 1/4" x 2" Button Head Bolts 1/4" Flat Washer (4) 2-3/4’’ Hex Head 5/16" Lock Washer Bolts i5.
PAGE 10
STEP 3 Insert (2) 5/16’’ T-Nuts (4) 3’’ Hex Head Bolts (4) Lock Washers (4) Flat Washers T-Nut Lock Washer Flat Washer WM 123 Hex Head Bolt 5/16" x 4 1/4" Hex Head Bolt d7. (1) WM 141 WM 142 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer d5a. (8) 5/16" Lock Washer i5.
PAGE 11
STEP 4 Hex Head Bolt Lock Washer Flat Washer FRAME ‘A’ Hex Head Bolt Lock Washer Flat Washer x 4 1/4 " Hex Head Bolt 5/16" x 4 1/4" 5/16 Hex" Head Bolt d7. (1) 1) " x Bolt 5/16 3" Hex Head Bolt 5/16" x 3" Hex Head 5/16" x 4 1/4" Hex Head Bolt (4) f1. (26) x 2 1/4 " Hex Head Bolt Hex" Head Bolt 5/16" x 2 1/4" 5/16 5/16" x 2 3/4" Hex Head Bolt d5a. (8) 26) 3) (4) x 2 3/4 " Hex Head Bolt 5/16" x 2 3/4" 5/16 Hex" Head Bolt 5/16" x 3" Hex Head Bolt f1. (26) 4) 8) d7. (1) d5a.
PAGE 12
STEP 5 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) (1) WM 121 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer d5a. (8) 5/16" Lock Washer i5. (33) (69) 1/4" x 2" Button Head Bolts (3) 1/4" Flat Washer 11 -1 (16) (3) (5)/2’’ 3" Square Slotted Screws (2) WM 108 1/4" Lock Washer 5/16" x 3" Hex Head Screws 2-1/2" Square Slotted Screws (60) (2) WM 122 1 3/4" Square Slotted Screws 5/16" x 4 1/4" Hex Head Bolt (2) d7.
PAGE 13
STEP 6 Lock Washer FRAME ‘B’ T-Nut Flat Washer Hex Head Bolt 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer d5a. (8) 5/16" Lock Washer i5. (33) (69) x 4 1/4 " Hex 1/4" 5/16 x 2" "Button Head BoltsHead Bolt (3)(1) d7.
PAGE 14
STEP 7 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer d5a. (8) (4) WM 107 (69) 5/16" Lock W i5. (33) 1/4" x 2" Button Head Bolts (3) 1/4" Flat Washer (5) 3" Square Slotted Screws 1/4" Lock Wa (3) (16) (16) 3’’ Square Slotted 2-1/2 " Square Slotted Screws (60) 1. Attach the Ladder Steps as shown.
PAGE 15
STEP 8 5/16" x 4 1/4" Hex Head Bolt d7. (1) WM 102-B (4) WM 102-A 5/16" x 2 3/4" Hex Head102-B Bolt WM f1. (26) WM 102-C " Hex 102-B Head Bolt 5/16" x 2 1/4 WM d5a. (8) WM 102-A WM 102-B 1/4" x 2" Button Head Bolts WM 102-C (3) WM 102-B 3" Square Screws WMSlotted 102-A (16)WM 102-C 5/16" x 3" Hex Head Bolt 5/16" Flat Washer (69) 1/4" Flat Washer 5/16" i5.
PAGE 16
STEP 9 1/4-20 T-Nut Climbing Rock 1/4” Lock Washer 8mm Washer 1/4”-20 x 2-1/4 Hex Head Bolt 1. Attach Climbing Rocks as shown with hardware included with accessory.
PAGE 17
STEP 10 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt 1. (26) (6) 2’’ Self Tapping x 2 1/4" Hex Head Bolt 5/16" Screws (6)" Flat Washers 5a. (8) 5/16 x 4 1/4" Hex Head Bolt Per Board 7. (1) (1) WM 150 5/16" Flat Washer 5/16" Lock Washer i5.
PAGE 18
STEP 11 ALL GAPS 1/4’’ (12) WM 112 WM 112-1 WM 146 WM 112-2 5/16" x 4 1/4" Hex Head Bolt WM 112-1 d7. (1) 5/16" x 4 1/4" Hex Head Bolt 5/16" x 3" Hex Head Bolt (4) d7. (1) 5/16" x 3" Hex Head Bolt " x Deck 2 3/4" Hex Head Bolt (2) 15/16 1/4’’ (4) f1. (26) Screws WM 146 5/16" x 2 3/4" Hex Head Bolt 5/16" x 2 1/4" Hex Head Bolt f1. (26) d5a. (8) 5/16" Flat Washer AL I E 1/4"d5a.
PAGE 19
STEP 12 5/16" x 4 1/4" Hex Head Bolt 1) 5/16" x 3" Hex Head Bolt 4) 5/16" x 2 3/4" Hex Head Bolt 6) WM 109 L 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer 8) 3) ) 3" Square Slotted Screws 5/16" x 3" Hex Head Bolt (16) 1/4" Flat Washer ) 1 3/4" Square Slotted Screws ) 5/16" x 3" Hex Head Screws 5/16" Flat Washer 1 1/4" Square Slotted Screws 191) 1/4" x 2" Button Head Bolts 3) d7.
PAGE 20
STEP 13 NOTE: Holes in barrier boards must align with holes in Swing Beam Support Board. (2) WM 151 (2) WM 152 (2) WM 153 (2) WM 154 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt ALL GAPS 3-1/8’’ 5/16" Flat Washer d5a. (8) (69) 5/16" Lock Washer i5.
PAGE 21
STEP 14 (2) WM 145 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 4 1/4" Hex Head Bolt 5/16" x 2 3/4" Hex Head Bolt d7. (1) f1. (26) 5/16" x 3" Hex Head Bolt 5/16" x 2 1/4" Hex Head Bolt 5/16"(4)Flat Washer d5a. (8) 2 Hex Head Bolt 5/16" x 2 3/4" Hex Head Bolt f1. (26) (3) 2 1/4 Hex Head Bolt i5. (33) (69) 1/4" x 2" Button Head Bolts 5/16" Lock Washer 1/4" Flat Washer 1/4" Lock Washer 5/16" x 2 1/4" Hex Head Bolt (3) (5) 3" Square Slotted Screws d5a.
PAGE 22
STEP 15 (2) WM 147 (2) WM 148 (4) 1 1/4’’ Square5/16" Slotted Screws d7. (1) (2) WM 149 x 4 1/4" Hex Head Bolt 5/16" x 3" Hex Head Bolt (1) WM 158 (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt 5/16" x 4 1/4" Hex Head Bolt Bolt 5/16" Flat Wash d5a. (8) (69) d7. (1) 1/4" x 2" Button Head Bolts 5/16" x 3" Hex Head Bolt (3) 1/4" Flat Wash (4) 5/16" x 2 3/4" Hex Head Bolt Head Bolt (5) 3" Square Slotted Screws (16) f1.
PAGE 23
STEP 16 5/16" x 4 1/4" Hex Head Bolt d7. (1) (6) WM 145 5/16" x 3" Hex Head Bolt (4) 5/16" x 4 1/4" Hex Head Bolt 5/16" x 2 3/4" Hex Head Bolt d7. (1) f1. (26) 5/16" x 3" Hex Head Bolt 5/16" Flat Washer 5/16" Lock Washer 5/16" x 2 1/4" Hex Head Bolt (4) d5a. (8) (69) i5. (33) 5/16" x 2 3/4" Hex Head Bolt 1/4" x 2" Button Head Bolts 2 Hex Head Bolt f1. (26) (3) 2 1/4 Hex Head Bolt 1/4" Flat Washer 1/4" Lock Washer 5/16" x 2 1/4" Hex Head Bolt (3) (5) 3" Square Slotted Screws d5a.
PAGE 24
STEP 17 T-nuts a NOTE: High edge of WQ136 goes towards the inside of the swing assembly i5 d5a i5 d5a i5 d5a i5.
PAGE 25
STEP 18 i5 d5a 5/16" Flat Washer 5/16" Lock Washer i5. (33) (69) 1/4" Flat Washer 1/4" Lock Washer (3) 5/16" x 4 1/4" Hex Head Bolt (5) d7. (1) 5/16" x 3" Hex Head Screws CENTER AND ATTACH ID-TAG WITH 3/4" DECK SCREWS 5/16"Head x 3" Bolt Hex Head Bolt 5/16" x 4 1/4" Hex 16" x 4 1/4" Hex Head Bolt (4) d7. (1) " xBolt 2 3/4" Hex Head Bolt 5/16" x 3" Hex5/16 Head 16" x 3" Hex Head Bolt f1.
PAGE 26
STEP 19 1’’ Overhang Per side (14) WM 127 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 2 1/4" Hex Head Bolt (56) 1’’ Bugle Head Self Tapping Screws 5/16" Flat Washer d5a.
PAGE 27
STEP 20 (2) SAFETY HANDLES (2) SAFETY HANDLES 1. Install safety handles as shown using hardware included with accessories.
PAGE 28
STEP 21 Button Head Bolt Lock Washer Flat Washer 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 3" Hex Head Bolt (4) 5/16" x 2 3/4" Hex Head Bolt f1. (26) 5/16" x 4 1/4" Hex Head Bolt d7. (1) 5/16" x 2 1/4" Hex Head Bolt 5/16" Flat Washer 5/16" x 3" Hexd5a. Head (8)Bolt 1/4" x 2" Button Head Bolts 5/16" x 2 3/4" Hex Head Bolt (3) 4f1.
PAGE 29
STEP 22 STEP 1: Follow Swing Hanger inﬆall. STEP 2: Follow Swing Seat inﬆall. STEP 3: Follow Ring-Trap inﬆall. SWING SEAT INSTALLATION T-Nut RING-TRAP INSTALLATION * Attach Quick Links to chain as shown in (1). * Attach Quick Links to Rings as shown in (2). * * Attach Trapeze Bar as shown. * Tighten all Quick Links fully closed with a suitable wrench, as shown. * Hang one chain from each swing hanger.
PAGE 30
STEP 23 Steering Wheel 5/16’’ Flat Washer T-Nut 5/16’’ Lock Washer 5/16’’ x 2-1/4’’ Hex Bolt 5/16’’ Diameter Hole Steering Wheel Cap 1. Choose the location on your Swing Set for your Steering Wheel. Drill a 5/16’’ diameter hole through the supporting lumber. 2. Install the Steering Wheel as shown using hardware included with accessory. Note: If the supporting lumber is thinner than 2’’ you will need to cut off any extra threads protruding through the T-Nut.
PAGE 31
STEP 24 CreativeCedarDesigns.
PAGE 32
CC 3710 888-363-4967 Got Questions? We’ve got answers! Call our Customer Support Representatives Available Monday - Friday, 9am - 4pm (EST) Technical Support from experienced Customer Service Representatives who have actually built a swing set themselves. Visit our web site at: www.Creativecedardesigns.