Creative X-Fi Sonic Carrier (Model MF8235) X-Fi Sonic Carrier Subwoofer(Model MF8240) User Manual For the latest information, visit: www.creative.com/support/soniccarrier Product Registration Registering your product ensures you receive the most appropriate service and product support available. You can register your product during installation or at http://www.creative.com/register. Please note that your warranty rights are not dependent on registration.
Package Content Main Unit Sonic Carrier Main unit IR remote control AAA Battery x 2 for IR remote control IR Blaster Wall mount brackets + hardware Wall mount bracket installation template Driver décor rings x 8 Power cable Warranty / Tech Support booklet Safety and regulatory leaflets QSG Subwoofer Subwoofer Power cable Link cable Warranty / Tech Support booklet Safety and regulatory leaflet Inserting Batteries (AAA Battery x 2) Slide the battery cover in the direction o
Sonic Carrier Main unit Overview Top Panel Front Panel Rear Panel
Remote Control Power: Turn On/Off Main Power. LED: Cycles to the next LED preset on all the Subwoofers. HDMI: Press to Switch to the last accessed HDMI source, or to cycle between available HDMI sources. SD: Press to Switch to the last accessed SD card, or to cycle between available SD cards. USB: Press to Switch to the last accessed USB drive, or to cycle between available USB drives HDMI: Press to Switch to the last accessed Optical input, or to cycle between available optical inputs.
Subwoofer Rear Panel Mode: Multifunction key. Press to toggle between lighting modes. Hold for wireless association mode Out: Audio and data output port IN: Audio and data input port Service: USB ‘A’ connector for service only Connecting Electrical Power Connect the power cords to the main unit and subwoofers, socket location are located at the back of the units and are marked below. Connect power cords to the mains socket.
Setting up the wireless subwoofer connection 1. Ensure the Main unit and Subwoofer are placed within 3M for the setup process 2. Ensure mains power is connected and switched on 3. Power on the Main unit by pressing the power button 4.
5. Place main unit in association mode by pressing “Power” and “HDMI 1” simultaneously. 6. Main unit and Subwoofer wireless is established when the subwoofer ring light flashes blue. Connecting to your TV 1. Connect the HDMI cable as shown in the illustration below 2. When TV sound is present, it is output automatically 3. If you are placing the Sonic Carrier on a console, and it is blocking the IR remote control sensor of the TV, please install the bundled IR transmitter as shown.
Connecting external devices The sonic carrier is equipped with a wide range of connectivity options. The following connection map illustrates the possibilities of connection, cable type needed, as well as the corresponding ports to connect to at the source. 1. HDMI Connection HDMI Cable (Not supplied) 2. Optical Connection 3. USB Connection Front and Rear USB ports could be used to connect to USB flash drives or USB Hard disk drives.
A pair of ¼” microphone inputs (Mic In 1, 2) is also located on the front panel, and supports most cardioid type dynamic microphones. A pair of stereo RCA analog Line inputs, and a pair of Stereo RCA Line analog line outputs are located at the rear panel. Please note the color and channel assignment of the RCA cable during connection (White = Left, Red = Right) 6. SD Cards 1 SD and 3 Micro-SD card slots are located at the front of the main unit.
Connecting to your WiFi network 1. Press Power and Wi-Fi buttons simultaneously to enter setup mode. 2. Sonic Carrier becomes an Access Point (AP) with SSID SonicCarrierConfigure_XXXXXX. Where XXXXXX is a randomly generated identifier. 3. Front Panel should display “Wi-Fi Setup Mode” 4.
5. Launch a browser and Enter 192.168.43.1 to enter the setup WebUI 6. Select the WiFi network to connect to, enter the passcode and click on “Save” 7. A confirmation message will be displayed after successful connection.
Switch between available USB inputs. Switch between available Optical Inputs Switch to Line Input Switch to Aux Input Cycle LED patterns on Subwoofer. All LED patterns can be cycled, the LCD display will show the LED name USB OPT L-In Aux LED Specifications DIMENSIONS AND WEIGHT MAIN UNIT Product name :CREATIVE X-FI SONIC CARRIER Model Number :MF8235 Input rating :100~240V 50/60Hz 120W. Operating temperature range: 0°C to 45°C Dimensions (L x W x H) :1521 x 151 x 96mm (59.9” x 5.9” x 3.
WI-FI AUDIO Supports DLNA, Tidal and Spotify Connect DRIVERS AND ACOUSTICS Sonic Carrier Main Unit Drivers o Five 1” coated aluminum alloy tweeters, capable of 40kHz high frequency reproduction o Eight 2.75” aluminum-magnesium alloy midbass drivers with individually sealed enclosures o Two 2.
Decoder support: Dolby Atmos, Dolby TrueHD, Dolby Digital Plus™, DTS:X upgradeable via firmware update Power supply: Auto-switching 100-240 V, 50-60 Hz AC universal input Bluetooth - Bluetooth version: 4.1 - Operating Frequency: 2402-2480MHz - RF Output Power: <4dBm - Bluetooth version: 4.0+EDR - Operating Frequency: 2402-2480MHz - RF Output Power: <6.12dBm Wi-Fi 2.4GHz - 802.11b/g/n - Operating Frequency: 2402-2480MHz - RF Output Power: <13dBm Wi-Fi 5GHz - 802.
