User Guide

90 Degree Upeasing Upeasing that quickly transitions
hand rail from level to vertical.
Baluster Decorative vertical member of a balustrade
system. Balusters are usually 1-1/4", 1-5/8" or
1-3/4" square.
Balustrade Hand rail system located on the open side of
a stairway that consists of newel post, balusters, and rail
components.
Box Newel Type of newel that is usually constructed like a
box, often having a hollow center. Box newels are usually
square rather than turned on a lathe.
Carriage A supporting member running the length of
the stairway on which treads, risers, and balustrade are
mounted (also referred to as rough stringers or rough
horses).
Coped End Fitting Hand rail fitting with one end coped
to match the profile of a fitting cap. When attached to the
hand rail on one end and
a cap on the other, the installer can build special
angle fittings.
Cove Mould Decorative trim which is used to cover the
joint between the tread/riser and the landing tread/
landing face.
False Riser Economical alternative to a full riser. Riser
cap is installed over a portion of the rough framed riser to
simulate the look of a solid riser. Ideal for center carpeted
stairways.
False Tread Economical alterative to a full tread. Tread
cap is installed over a portion of the rough framed tread
on the open side of a stairway to simulate the look of a
solid tread. Ideal for center carpeted stairways.
Fillet Decorative wood strips used to fill the plow between
balusters on plowed hand rail and plowed shoe rail.
Gooseneck Fitting consisting of one or two upeasings, one
rail drop, and one or two level fitting components. Used to
make transitions at landings.
Hand Rail Portion of the balustrade system which sits on
top of the balusters and is supported by the newel posts.
Hand Rail Fittings Components that make transitions in
hand rail height or pitch. Also allows the hand rail to run
over the newel post. Components attach to the hand rail
and are profiled to match the hand rail pattern.
Intermediate Landing Platform separating flights of
stairs.
Intermediate Newel Post Newel post at the corner of an
intermediate landing where two rake rails meet.
Kneewall Wall on the balustrade system side of the
stair that extends just a few inches above the nose of the
treads. The balustrade system attaches to the kneewall
and adjacent framing members.
Landing Newel Newel post at the top of a flight of steps,
located at the point where a rake hand rail and a level
hand rail intersect.
Landing Tread Moulding used to give the appearance
of a tread with nosing at the top riser of a flight of stairs
and along the open edge of second floor balconies and
intermediate landings.
Newel Post Major support post in balustrade system.
Newel posts are located at the bottom and top of flights
of stairs, as support posts in long balustrade lengths on
second floor landings, and at direction changes.
Pin Top Balusters Balusters with a turned area that
extend to the top of the baluster. They are connected to
the hand rail by inserting the round top of the baluster
into a hole drilled in the bottom of the hand rail.
Riser Vertical component of a step which your toe might
hit when walking on a stairway.
Rosette Decorative piece used where the hand rail
meets a wall.
Second Floor Landing Floor area at the top of a
stairway. The second floor landing is commonly referred
to as the balcony.
Shoe Mould Decorative moulding used to cover the joint
between the bottom riser and the floor.
Shoe Rail Plowed bottom rail of a balustrade system,
which houses the bottom block of a baluster.
Skirtboard Decorative trim board used in carriage built
stairways to trim the area of the carriage on the open
side of the stairway and as a moulding on the closed side
of the stairway.
Square Top Balusters Balusters that are square on the
top and bottom. Fits securely in a plowed hand rail.
Starting Easing Fitting used as a decorative beginning
at the bottom of a wall rail.
Starting Fitting Decorative beginning to an over the post
hand rail system.
Starting Newel Newel used at the bottom of a stairway.
Starting Step Bottom tread and riser of a stair. Starting
steps often have rounded ends, called bullnoses, that
extend beyond the carriage of the stairway. Bullnosed
starting steps are necessary for over the post
balustrades beginning with volutes or turnouts.
Tread The part of a step that is walked on.
Tread Bracket Decorative piece mitered to the riser and
fastened on the side of an open skirtboard.
STAIRWAY GLOSSARY