User guide

LIMITATION OF REMEDIES AND DAMAGES
THE ONLY REMEDY FOR BREACH OF WARRANTY WILL BE
THAT SET FORTH IN THE WARRANTY CARD OR PRINTED
MANUAL INCLUDED WITH THE SOFTWARE. IN NO EVENT
WILL CREATIVE OR ITS LICENSORS BE LIABLE FOR ANY
INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES OR FOR ANY LOST PROFITS, LOST SAVINGS,
LOST REVENUES OR LOST DATA ARISING FROM OR
RELATING TO THE SOFTWARE OR THIS AGREEMENT,
EVEN IF CREATIVE OR ITS LICENSORS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO
EVENT WILL CREATIVE’S LIABILITY OR DAMAGES TO
YOU OR ANY OTHER PERSON EVER EXCEED THE AMOUNT
PAID BY YOU TO USE THE SOFTWARE, REGARDLESS OF
THE FORM OF THE CLAIM.
Some countries/states do not allow the limitation or exclusion of liability
for incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
PRODUCT RETURNS
If you must ship the software to Creative or an authorized Creative
distributor or dealer, you must prepay shipping and either insure the
software or assume all risk of loss or damage in transit.
U.S. GOVERNMENT RESTRICTED RIGHTS
All Software and related documentation are provided with restricted
rights. Use, duplication or disclosure by the U.S. Government is subject
to restrictions as set forth in subdivision (b)(3)(ii) of the Rights in
Technical Data and Computer Software Clause at 252.227-7013. If you
are sub-licensing or using the Software outside of the United States, you
will comply with the applicable local laws of your country, U.S. export
control law, and the English version of this Agreement.
CONTRACTOR/MANUFACTURER
The Contractor/Manufacturer for the Software is:
Creative Technology Ltd
31, International Business Park
Creative Resource
Singapore 609921
GENERAL
This Agreement is binding on you as well as your employees, employers,
contractors and agents, and on any successors and assignees. Neither the
Software nor any information derived therefrom may be exported except
in accordance with the laws of the U.S. or other applicable provisions.
This Agreement is governed by the laws of the State of California
(except to the extent federal law governs copyrights and federally
registered trademarks). This Agreement is the entire agreement between
us and supersedes any other understandings or agreements, including,
but not limited to, advertising, with respect to the Software. If any
provision of this Agreement is deemed invalid or unenforceable by any
country or government agency having jurisdiction, that particular
provision will be deemed modified to the extent necessary to make the
provision valid and enforceable, and the remaining provisions will
remain in full force and effect.
For questions concerning this Agreement, please contact Creative at the
address stated above. For questions on product or technical matters,
contact the Creative technical support center nearest you.
ADDENDUM TO THE MICROSOFT SOFTWARE LICENSE
AGREEMENT (WINDOWS 95)
IMPORTANT: By using the Microsoft software files (the “Microsoft
Software”) provided with this Addendum, you are agreeing to be bound
by the following terms. If you do not agree to be bound by these terms,
you may not use the Microsoft Software.
The Microsoft Software is provided for the sole purpose of replacing the
corresponding files provided with a previously licensed copy of the
Microsoft software product identified above (“ORIGINAL
PRODUCT”). Upon installation, the Microsoft Software files become
part of the ORIGINAL PRODUCT and are subject to the same warranty
and license terms and conditions as the ORIGINAL PRODUCT. If you
do not have a valid license to use the ORIGINAL PRODUCT, you may
not use the Microsoft Software. Any other use of the Microsoft Software
Safety Information
The following sections contain notices for various countries:
CAUTION: This device is intended to be installed by the user in a CSA/
TUV/UL certified/listed IBM AT or compatible personal computers in
the manufacturer’s defined operator access area. Check the equipment
operating/installation manual and/or with the equipment manufacturer to
verify/confirm if your equipment is suitable for user-installed
application cards.
ATTENTION: Ce carte est destiné à être installé par l’utilisateur, dans
un ordinateur compatible certifié CSA/TUV/UL ou listé IBM AT, à
l’intérieur de la zone définie par le fabricant. Consulter le mode
d’emploi ou le fabricant de l’appareil pour vérifier ou confirmer si
l’utilisateur peut y installer lui-même des cartes périphériques.
Notice for the USA
FCC Part 15: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, this notice is
not a guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try one or more of the following measures:
❑ Reorient or relocate the receiving antenna.
❑ Increase the distance between the equipment and receiver.
❑ Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
❑ Consult the dealer or an experienced radio/TV technician.
Caution
To comply with the limits for the Class B digital device, pursuant to Part
15 of the FCC Rules, this device must be installed in computer
equipment certified to comply with the Class B limits.
All cables used to connect the computer and peripherals must be shielded
and grounded. Operation with non-certified computers or non-shielded
cables may result in interference to radio or television reception.
Modifications
Any changes or modifications not expressly approved by the grantee of
this device could void the user’s authority to operate the device.
Notice for Canada
This apparatus complies with the Class “B” limits for radio interference
as specified in the Canadian Department of Communications Radio
Interference Regulations.
Cet appareil est conforme aux normes de CLASSE “B” d’interference
radio tel que spécifié par le Ministère Canadien des Communications
dans les règlements d’interférence radio.
Compliance
This product conforms to the following Council Directive:
❑ Directive 89/336/EEC, 92/31/EEC (EMC)
Declaration of Conformity
According to the FCC96 208 and ET95-19 documents,
Name: Creative Labs Inc.
Address: 1901 McCarthy Boulevard
Milpitas, CA. 95035
United States
Tel: [phone]
declares under its sole responsibility that the product
Trade Name: Creative Labs
Model Number: DAP-3201
has been tested according to the FCC / CISPR22/85
requirements for Class B devices and found compliant with
the following standards
EMI/EMC: ANSI C63.4 1992, FCC Part 15 Subpart B
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesirable operation.
Ce matériel est conforme à la section 15 des régles FCC. Son
Fonctionnement est soumis aux deux conditions suivantes:
1. Le matériel ne peut étre source D’interférences et
2. Doit accepter toutes les interférences reques, Y compris celles
pouvant provoquer un fonctionnement indésirable.
Compliance Manager
Creative Labs, Inc.
1999