User guide

ManualsBrandsCreda ManualsCooktopC150

HOW TO USE YOUR SPA200 SHOWER (SUMMARY)

IMPORTANT WARNINGS!

DO NOT SWITCH THE APPLIANCE ON IF YOU SUSPECT IT OF BEING FROZEN.

WAIT UNTIL YOU ARE SURE IT HAS THAWED OUT.

DO NOT OPERATE THE APPLIANCE IF WATER DISCHARGES FROM THE PRESSURE RELIEF

VALVE. MAINTENANCE IS REQUIRED BEFORE THE APPLIANCE CAN BE SAFELY USED.

THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN

AND

THE INFIRM) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, OR LACK OF

EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR

INSTRUCTION CONCERNING USE OF THE APPLIANCE

BY A PERSON RESPONSIBLE FOR THEIR SAFETY.

CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY

DO NOT PLAY WITH THE APPLIANCE.

1. Ensure the electricity and water are turned on to the unit.

2. Press the start / stop button “B”.

This will turn the shower on, the water will flow and the

indicator lights will glow showing chosen Power Selection.

We recommended that you do not enter the water spray

during this period, even if the shower has just been used.

3. Knob “A” controls the power selection.

Select “High”, “Med (medium)” or “Cold”

4. If the water is not at your desired showering

temperature, turn knob “C” a small amount until

you reach the desired showering temperature.

Turn clockwise (follow blue arrows) for cooler.

Turn anti-clockwise (follow red arrows) for warmer.

s a helpful guide the knob position is indicated by a number being displayed in Window “D”.

On the scale “1” is the coolest, whilst “9” is the hottest.

5. When you have finished showering, press the start / stop button “B” again.

6. Water will continue to flow for up to 7 seconds before switching off.

This reduces the temperature of the water in the tank for

the next user.

The indicator lights will go out.

7. Wait for the water to stop, switch off the electricity supply at the ceiling switch or local isolator.

Notes

• Wait 20 seconds for the temperature to stabilise after each adjustment.

• The indicator lights illuminate when the heaters are on and, if the shower has been

recently used, they may take up to 20 seconds to come on.

During this time the water may go from very hot to cold before stabilising.

• The position of knob “C” will be approximately the same each time the shower is

used, varying only with incoming water temperature or pressure changes

(e.g. you will only need to change from summer to winter).

• During normal operation, if an overheated water temperature is sensed then the

heater will switch off and the “Overheat” light will illuminate.

Water will continue to flow and cool down before the heater switches back on again.

We offer a technical advisory service on the telephone: RING 0844 372 7766 (UK ONLY)

(A4) Leaflet No. 555-2138-61b

IMPORTANT:

This booklet should be left with the user after

installation and demonstration

CREDA SPA200

SMART TECHNOLOGY

ELECTRIC SHOWER

Installation and User Guide

Summary of content (6 pages)

PAGE 1
HOW TO USE YOUR SPA200 SHOWER (SUMMARY) 1. Ensure the electricity and water are turned on to the unit. 2. Press the start / stop button “B”. This will turn the shower on, the water will flow and the indicator lights will glow showing chosen Power Selection. We recommended that you do not enter the water spray during this period, even if the shower has just been used. 3. Knob “A” controls the power selection. Select “High”, “Med (medium)” or “Cold” 4.
PAGE 2
: GUARANTEE AND CONTACT DETAILS CONTENTS Section Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important Safety Information . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to install your SPA200 Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to maintain your SPA200 Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
HOW YOUR SPA200 SHOWER WORKS HOW TO INSTALL YOUR SPA200 SHOWER 1. Water is heated instantaneously as it flows over the heating elements in the copper cylinder (Diagram 8). WARNING: ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A SUITABLY QUALIFIED PERSON. 2. The heaters are only switched on when sufficient water is flowing. This is done automatically with a switch which works on water pressure and is indicated by 2 or 3 lights illuminating depending on knob “A” power selection.
PAGE 4
7. If you have not yet done so, remove the front cover assembly by undoing the retaining screws at the top and bottom of the unit and lifting the cover off. Your shower is provided with 2 fixing positions in the backplate (see Diagram 7 on page 9). The top-fixing hole is a “key-hole” slot (another key-hole is provided for alternate fixing), and should be marked and drilled first. Tighten top screw with head protruding about 10mm from the wall and hook the backplate over the screw head.
PAGE 5
WHAT TO DO IF THINGS GO WRONG (1) WARNING: THIS SHOWER MUST BE EARTHED. SELF HELP If the shower is not working satisfactorily, make the following checks before calling out the installer. Any one of these adjustments could restore the performance. The shower cycles The shower temperature is set too hot causing the thermal cut-out (safety from HOT to COLD device) to operate. Turn knob “C” clockwise (following the “blue arrows”) to increase water flow.
PAGE 6
5. Re-Fit the front cover (see Diagram 5), and secure by replacing the top and bottom fastening screws. Ensure knob “A” is aligned to the “High” position. Ensure knob “C” is aligned to “12 o’clock. In the main body of the shower, turn the “Camshaft” as shown. In the main body of the shower, turn the “Numbered Dial” fully clockwise until it is at the position shown. Note:- this instruction should be used if the “Drive Dial” becomes accidentally dislodged. e.