COOKER HOOD USER HANDBOOK FOR INSTALLATION AND OPERATION MODEL CRC60
Your new Cooker Hood Using your new Cooker Hood is very simple. Nevertheless, to get the best results it is important that you read this handbook thoroughly before installing and using your appliance for the first time. Electrical Requirements Any permanent electrical installation must comply with the latest I.E.E. Regulations and local electricity company regulations. For your own safety, this should be undertaken by a qualified electrician eg.
Contents Page Electrical Requirements Get to know your Cooker Hood Installing your Cooker Hood Operating your Cooker Hood The Controls Do’s and Don’ts Caring for your Cooker Hood Filters and their Replacement Cleaning How to Replace the Light Troubleshooting Key Contacts 2 4 5-8 9 10-11 12 Back Cover Appliance manufactured in EU. Retention of the Instruction Book This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance.
Get to know your Cooker Hood. Unpacking Before installation, ensure that you have removed all packing pieces. Ensure the fixing kit, ducting spigots and literature pack are retained with the hood. Recirculation Grilles Chimney Section Hob Lights Controls Filter Grilles Hob Lights On/Off Fan Speed Performance Table No.
Installing your Cooker Hood SAFETY WARNINGS: THIS COOKER HOOD IS DESIGNED FOR DOMESTIC USE ONLY. When installed above a cooking appliance, the distance between the surface of the hob elements and the lower grille of the chimney hood must be as follows: Minimum 650mm - over an electric hob. Minimum 700mm - over a gas or mixed fuel hob. This chimney hood is not suitable for installation above a cooking appliance with a high level grill.
Installing your Cooker Hood WALL FIXINGS: Lower Fixings 1. Draw a vertical line on the wall, from the centre of the cooking appliance, up to the ceiling. Check the line is vertical using a spirit level. 2. Put the template provided on the wall and drill two ø12mm holes (Fig.1 2) 3. Fit two hooks in the drilled holes (Fig.1 3). Upper Fixing Bracket 1. Draw a horizontal line through the vertical line, 15mm from the ceiling. Check the line is level using a spirit level. 2.
Installing your Cooker Hood RECIRCULATION: The chimney hood is supplied specified for installation in the extraction mode. To convert to recirculation it will be necessary to obtain the optional pack of two carbon filters. In the recirculation mode, contaminated air enters the chimney hood and passes through the grease filters and carbon filters and then out into the kitchen through two grilles, at either side of the lower chimney. To convert the chimney hood to recirculation proceed as follows: 1.
Installing your Cooker Hood Fitting the Chimney Stack: To fit the upper chimney section, first expand the chimney slightly to allow it to be fitted over the wall brackets. Then secure the upper section using the four self tapping screws provided. The lower chimney section should be located following instructions on page 6, ensuring that the lugs in the base of the chimney are seated into the two recesses on either side of the canopy (Fig.5). Fig.
Operating your Cooker Hood The Controls Make sure that the Cooker Hood is wired in and the power supply is switched on. The Cooker Hood functions are controlled by two slide switches, located front centre on the underside of the hood. To obtain the best performance it is advisable to switch on the chimney hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. Fan Speed The right slider enables you to select the fan speed.
Caring for your Cooker Hood Before doing any cleaning or replacing the filters or light bulb, always ensure that the electricity supply to the Cooker Hood is switched ‘OFF’. Filters and their replacement: THE METAL GREASE FILTERS The grease filters are fitted to absorb grease and dust during cooking to help keep the appliance clean inside. The metal filters must be cleaned frequently, at least once every thirty days of normal use. The filters should be handwashed in hot soapy water.
Caring for your Cooker Hood Cleaning: For your own safety and in the interest of hygiene your Cooker Hood needs to be kept clean. A build up of grease or fat from cooking could cause a fire hazard. Never use excessive amounts of water when cleaning, particularly around the control panel area. The metal casing and grille assembly should be cleaned at least once a month to keep it looking like new. Wipe over with a soft cloth, wrung out in warm water and dry with a clean soft cloth. Wear protective gloves.
Troubleshooting. First, don’t panic! There may be nothing wrong at all. Look for your problem below, then check the things we suggest. More often than not, this will give you the answer to your problem, and you’ll be able to carry on without having to telephone your Service Office. It is not working! Are you using a plug and socket? - Check that the plug is firmly pushed in. - Check the power supply, by plugging in another appliance.
Key Contacts Service Creda has the largest appliance manufacturer’s service team in Europe, trained specialists directly employed by us to ensure your complete confidence. Repair Service UK: 08709 066 066 Republic of Ireland: 1850 302 200 You will be asked for the following information:Name, address and postcode.
