User Guide CQUBE M Espresso Your dealer U_EN Rev. 111124 Art. nr/Art. no. 1730136-02 CREM International AB Box 10, Viksgränd 2, SE-670 40 Åmotfors, Sweden Tel: +46 (0)570-477 00, Fax: +46 (0)570-47719 E-mail: info.se@creminternational.com www.creminternational.
1. Contents CQube Espresso 1. 2. 3. 3. 3. 3. 3. Contents General, Safety regulations, Fact, Overview, front Overview, mixer system Overview components, ingredients canister Overview membrane switch, button function front Overview user card 4. Installation and start-up, Position machine, Fit machine Connection of the hoses for cooling unit with carbonic acid, (base cab.
2. General . CQube Espresso Thank you for choosing a CQube espresso machine. We hope you enjoy it ! - The machine must be connected correctly for your own safety. Read the user guide before using the machine. - The guide contains important instructions for proper and safe use. - Always keep the guide close at hand. The machine must be disconnected from mains electricity supply before carrying out any maintenance. All installation work must be carried out by qualified personnel.
3. Overview, front. CQube Espresso Bean container Display Pre-selection buttons Energy-saving mode Stop Menu Drinks Card reader Door Lock Dispenser hot drinks Tap for water drinks Cup shelf Drip cover Drip tray Accessories; Base cabinet with carbonic acid tube and cooler 4.
3. Overview inside. CQube Espresso Beancontainer Ingredients canister Bean valve Chute Grinder Grinder dispenser ON/OFF switch Cleaning buttons Brewingmechanism Mixing bowl Grounds tray 5.
3. Overview of components, ingredients container. CQube Espresso Ingredients canister. Detail; Ingredients; Width Height KG Canister Canister Canister Beans Chocolate Topping Espresso maskin Behållare Behållare Topping Chocolate Cups in gram Amount of cups 160 67 67 180 250 250 2,0 1,5 1,1 14 20 9 143 76 122 160 67 250 250 2,9 1,5 0,01 0,02 291 76 6.
3. Overview: Membrane switch function, front 5. Overview of components, function buttons CQube Espresso AC12 Buttons function front. USER CARD Press the Back button if you want to leave the submenu and go back to the main menu. Press the Enter button if you want to enter the menu, change a value or a setting. Confirm the new setting by pressing the E-button. Press the buttons if you want to increase a value or browse through a menu.
3. Overview: USER CARD 5. Overview of components, function buttons CQube Espresso AC12 USER CARD USER CARD Item number: 1602692. Is used for cleaning and setting jug beverages. The user card is supplied by your dealer. For full menus. See Programming Manual. Insert the card: Display will show the Service Menu, Jug Beverage and you can now browse forwards through the menu. Service Menu Jug Beverage To use the machine again. Remove the card and keep it in a safe place. 8.
4. Installation and start-up. CQube Espresso 1. Place the machine on a flat surface that is impermeable to water. 2. With assembly with a base cabinet; Mount the machine's top cabinet with the M6 x 35 screws supplied. M6 x 35 90° Note: Make sure air is able to circulate freely behind the machine. (minimum 10cm). Note: Only for installation with cold water function. Installation of refrigeration unit with carbonic acid, (base cabinet) Figure 1. A 3. Connect the 8mm hoses 3 units.
4. Installation and start-up. CQube Espresso CARBONATED WATER WATER OUT Note: Do not connect the electrical cable from the cold water unit, before the machine has heated up for c.10 minutes. 4. Connect the carbon dioxide tube to the gas canister and open the tap, check that the factory set pressure is c. 3.5bar. May be adjusted +0.5 -1.0 bar. Put the carbon dioxide tube in place (figure 2). Figure 2.
4. Installation and start-up. CQube Espresso Connect the water to the top cabinet on the machine. 6. Connect the factory-supplied tube to the cold water feed using a ½” R- connection piece Make sure no folding or sharp bending occurs when you push the machine back in place. If the water pipe is new, flush the system with water first to remove copper shavings. These can damage the inlet valve. The new tube set supplied with the appliance must be used. Old tubes may not be reused.
4. Installation and start-up. CQube Espresso Start-up of coffee machine with built-in refrigeration unit for water 13. Now connect the electricity cable which comes from the bottom cabinet into the electric socket for the machine (B) in the top cabinet see figure 3). B 14. Switch on the machine again: and wait until the text in the display starts to rotate. Figure.3. ON Note: The fresh-brew machine must be warm before cold water can be dispensed. 15.
4. Installation and start-up. CQube Espresso 18. Fill the container. Fill ingredients into the containers. Remove the ingredients containers to avoid spilling in the machine) and fill with ingredients. 19. Fill the bean container with coffee beans. Lift the lid and fill the bean container with freshly roasted coffee beans without additives. (e.g. flavour essence and sugar), Open the valve (A) on the bean container. 20.
5. Operations. Brewing a cup of espresso, CQube Espresso Brewing a cup of espresso. 1. Put a cup under the espresso dispenser. 2. The strength of the drink is set to default. If you would like to increase or decrease the strength then follow the steps in the section below, otherwise proceed to Point 3. Stronger drink; Press + button alternatively Weaker drink; Press - button 3. Select drink espresso by pressing on the button espresso on the menu.
5. Operation. Brewing chocolate in a jug. CQube Espresso A 1. Put a jug under the espresso dispenser and fold up the cup shelf. 2. Insert the user card in the card reader(A) 3. The display shows Service Menu, Jug Beverage. 4. Press the 5. Change the number of cups you want to brew in your jug. (6 cups is the default setting.) with E button. alternative button. Brewing is possible for up to 12 cups or down to 1 cup. 6. Press the button for chocolate.
6. Cleaning programme; Clean brewing mechanism CQube Espresso Automatic cleaning with brewing mechanism: Cleaning the brewer mechanism should be done once a week. 1. Insert the user card in the card reader (A) 2. Move through the menu until the display shows Service Menu, Clean Machine. 3. Press the E button. 4. Move through the menu until the display shows Select Cleaning, Clean Brewer. 5. Press the E button. The display shows; Open Door, Fill Detergent. 6. Open the door.
6. Cleaning programme; Clean the brewing mechanism. CQube Espresso Continuation: 10. Press E-button to start cleaning. 11. Display indicates: Preparing unit, Please wait. 12. Cleaning Unit, Time Left 60 seconds. The machine counts down from 60 seconds. 13. Display indicates: Cleaning unit, Brewcycles left 3. Machine is now cleaning the system. 14. Close door. 15. Remove user card. Total cleaning time about 5 minutes.
6. Cleaning programme; Rinsing the blender bowls CQube Espresso Automatic rinsing of the blender bowls, at least once a day. A 1. Lift up the cup shelf. Put a container that takes c. 0.5 litres under the dispenser for espresso 2. Insert the user card in the card reader (A) 3. Move through the menu until the display shows Service Menu, Clean Machine. 4. Press 5. Move through the menu until the display shows Select Cleaning, Clean Mixer. 6. Press 7.
6. Cleaning programme; Dispenser valves CQube Espresso Automatic cleaning of dispenser valves: A Cleaning of dispenser valves 1. Lift up the cup shelf. Put a container under both the Espresso and Water dispensers. 2. Insert the user card in the card reader (A) 3. Move through the menu until the display shows Service Menu, Clean Machine. 4. Press 5. Move through the menu until the display shows Select Cleaning, Clean Valves. 6. Press 7.
6. Cleaning programme; Flush brew mechanism ESP CQube Espresso Flush brew mechanism with water if necessary. A Flush brew mechanism. 1. Lift up the cup shelf. Put a container under the Espresso dispenser. 2. Insert the user card in the card reader (A). 3. Move through the menu until the display shows Service Menu, Clean Machine. 4. Press 5. Move through the menu until the display shows Select Cleaning, Rinse Brewer ESP. 6. Press 7. Brew mechanism will now be flushed with water. 8.
7. CLEANING: CLEANING EVERY WEEK Disassemble: the blendersystem 1. Loosen canister and output hose. see fig. 1. 2. Turn the lever anticlockwise. see fig. 2. 3. Loosen the blender bowl by pull straight out. see fig. 3. Fig. 1. Fig. 2. Fig. 3. (C) 4. Loosen whisk by pulling it straight out. see fig. 4 5. Loosen the fixing plate. Turn the lever anticlockwise, until it stops.see fig. 5. Fig. 4. Fig. 5. Reassembly blendersystem. See next page. 21.
7. CLEANING: CLEANING EVERY WEEK Wash these parts. Blender bowl Condensation trap Fitting plate Whisk Clean with a moist cloth and wipe dry. All parts must be dry before reassembly. Reassembly blendersystem reversed. 6. 7. 8. CHECK all seals before reassembly of parts. See fig. 6. The plane side of the whisk motor shaft must correspond with the marking on the whisk. See fig. 7. Fit the whisk, push until a slight clicking sound can be heard. Follow the instructions of the blender, arrow.
8. Cleaning and care. CLEANING CQube Espresso Cleaning when necessary. When cleaning the bean container. 1. Close the dispenser valve 2. Lift the bean container up and remove it. Use a soft rag and liquid cleaning agent that is non abrasive. Note: Ensure that the bean container is completely dry before refitting. To clean the exterior of the machine, use a soft rag and liquid cleaning agent that is non-abrasive. Drip tray and drip tray insert should be washed by hand in ordinary dishwater.
9. Message shown on display CQube Espresso Message on display: The display indicates: Energy saving mode The machine is in energy saving mode. Not available Drink cannot be selected as jug. Heating Water Please Wait... Low temperature in the water tank, the machine is heating up (blocked) Low Water Level Press Enter Key Low water level in water tank. Filling Water Please wait The machine is filling water.
10. PROGRAMMING CQube Espresso Activate programming with the user card 1. 2. Insert the user card in the card reader The display indicates: Service Menu, Jug Beverage, Clean Machine, Counters Function buttons programming Back Press this button if you wish to leave the submenu and return to the main menu. Press the enter button if you want to enter a menu, alter the value or a setting. Alter a value by pressing the button or the button. Confirm the new setting by pressing the E-button.
11. PROGRAMMING MAIN MENU CQube Espresso PROGRAMMING AND SETTINGS. Service Menu Jug Beverage The display shows Press the button Service Menu Clean Machine The display shows Press the button Service Menu Counters The display shows 26.
11. PROGRAMMING Jug Beverage Alter Jug Beverage, Jug Setup Service Menu Jug Beverage Place card in the card reader. Display shows Jug Beverage Press the button CQube Espresso Select the number of cups to be brewed in jug Press Jug Beverage Cups 1 - 12 6 cups is standard Step forward in the menu Press If no selection is made, remove the user card to return to the default setting. To stop, press the STOP-button. 27.
11. PROGRAMMING Clean Machine CQube Espresso Cleaning Programm: Access Cleaning menus for the user card. Place card in card reader.
11. PROGRAMMING Counters CQube Espresso Se the number of performed cleanings or reset the counter: Place card in card reader. Step forward until Display shows Counters Press the button Press Press Counters Beverages Beverage counter Per beverage Drink 1 Served xxx to step forwards in the menu. Drink 2 Served xxx Press Press Beverage counter Total Served Total Beverages Served xxx to step forwards in the menu. Press Press to step forwards in the menu.
11. PROGRAMMING Counters CQube Espresso Se the number of performed cleanings or reset the counter: Counters, Cleaning Counter Step forward until Display shows Counters Press button Press Counters Clean Counter Clean Counter Brewer 000 to step forwards in the menu. Press Press button Clean Counter Milk 000 Clean Counter Total 000 to step backwards in the menu.
12. Dimension sketch. CQube Espresso Electricity connection Water connection 31.
FOR SERVICE Please contact your dealer ............................................................................... ............................................................................... ...............................................................................