LQ 10P BIAMPED POWERED SPEAKER User Manual
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
INTRODUCTION ENGLISH The Crest LQ™10P features a biamped power section that provides 200 Watts peak dynamic power for the woofer and 70 Watts peak dynamic power for the compression driver tweeter, both with power amplifier compression. Offering a 10" premium long-throw woofer and the Crest HF™-1 compression driver, the LQ 10P provides line-level balanced inputs with volume control and loop-thru jacks.
PANEL FEATURES Rear Panel Features 2 1 3 (1) FUSE The unit is AC power line fuse-protected from overloads and fault conditions with an ABC-type, fast-blow 5 Amp fuse. In the rare event of a fuse blowout, first make sure the unit is unplugged and the power switch is in the OFF position, then replace the blown fuse with a fast-blow, 5 Amp, 250 Volt AC-rated fuse ONLY. Be sure to fully seat and close the replacement fuse and fuse holder cap.
PANEL FEATURES Front Panel Features 5 4 7 6 (4) POWER LED Illuminates when the preamp electronics receive power and should illuminate when the On-Off Switch is in the ON position and the AC power cord is connected and plugged into the wall outlet. (5) LINE IN/THRU The input and output jacks are paralleled to allow the audio input signal to be daisy-chained to other devices.The “output” level is the same as the “input” level and there is no isolation between the various jacks.
Operating Instructions CAUTIONS The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to qualified service personnel. The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from ventilation. DO NOT connect the inputs of the LQ10P to the output of a power amplifier; the inputs are meant to be driven from a line level strength signal. DO NOT remove the protective metal grille.
USE OF THE LQ™ 10P FLYING THE LQ 10P Caution: Suspending or flying the Crest LQ 10P must be done by a certified structural engineer. Important Safety Information for Mounting Crest LQ 10P speaker systems: Caution: Before attempting to suspend these speaker models, consult a certified structural engineer. Speakers can fall from improper suspension, resulting in serious injury and property damage.
LQ™ 10P USER MANUAL Special note for permanent installation When installing the Crest LQ 10P, AC power runs should be used and a certified electrician consulted to be sure that all AC wiring complies with local codes and regulations. Properly affix a cable clip to the cabinet to relieve strain on the IEC power cord connected to the amplifier module at (2) so the power cord cannot vibrate loose.
LQ™ 10P User Manual flashing frequently, then the drive level from the mixer (or the Volume control on the LQ 10P) needs to be reduced. When first powering up the sound system, turn on all upstream electronics first, then the LQ 10P with its Volume control fully counterclockwise (all the way down). Begin checking levels with the mixer output level controls all the way down, then bring them up slowly with the LQ 10P Volume control set to the desired setting (halfway up recommended to start).
TROUBLESHOOTING If there is still no output, make sure the volume control has been turned up to a reasonable level (one-third to halfway). Has the LQ 10P been in direct sunlight or excessive heat? If so, it may have triggered the thermal protection.Turn off the unit and cool as best as the situation allows. (DO NOT use liquids for this purpose!) If there is still no output, it may help to read the owner’s manual completely. Hum or Buzz This can be AC outlet-related.
LQ™ 10P User Manual Finally, be aware that even though the LQ 10P is an extremely powerful and high output unit, it has limits and may need additional powered units or a subwoofer to provide enough sound output or coverage. In this case, try turning the mixer levels down a little to see if the sound clears up.
Care and Maintenance DESCRIPTION The Crest LQ 10P is a powered, bi-amplified, two-way speaker system engineered to provide the highest levels of performance and capable of over 120 dB peak SPLs.The enclosure utilizes high-impact polypropylene in an injection-molded plastic trapezoidal form with a coated, perforated metal grille to offer a cosmetically elegant yet durable powered speaker system.
Architectural & Engineering Specifications The input signal is electronically divided into high frequencies and low frequencies by a staggered pole, third order slope line-level crossover at 2 kHz.The low frequencies are processed to provide bass boost, subsonic filtering and overall response shaping, and the high frequencies are equalized for constant-directivity horn EQ and response shaping.
SPECIFICATIONS LQ™ 10P Enclosure: Crest LQ™10P (domestic) Enclosure materials and finish: Injection-molded high-impact polypropylene of a 1/4" nominal thickness with internal ribbing and bracing, textured finish, and a UL flame rating. Molded material is dark gray. Frequency response: 80 Hz to 20 kHz Mounting: Flying via Omnimount™ 75 series (top or bottom of cabinet) and four rubber feet for floor use. Array brackets are available. Low frequency limit (-3 dB point): 80 Hz Dimensions: Front: 18.
Graphics LQ™ 10P Graphics Amplitude Response (1W 1m On-Axis) dB SPL (re 20 Pa) 110 100 90 80 70 60 20 50 100 200 Figure 1 500 1k Frequency (Hz) 2k 5k 10k 20k 2k 5k 10k 20k Beamwidth Beamwidth (Degrees) 360 300 180 140 100 80 60 40 30 20 Horizontal Vertical 50 100 200 Figure 2 500 1k Frequency (Hz) Q & Directivity Index 20 100 Q Di 10 10 1 20 Figure 3 50 100 200 500 1k Frequency (Hz) 16 2k 5k 10k 0 20k
Graphics LQ™ 10P Graphics Harmonic Distortion : 1% Rated Power 120 110 dB SPL (re 20 Pa) 100 90 80 70 60 50 40 20 50 100 200 500 1k 2k 5k 10k 20k 5k 10k 20k Frequency (Hz) 2nd Harmonic 3rd Harmonic Harmonic Distortion : 10% Rated Power 130 120 dB SPL (re 20 Pa) 110 100 90 80 70 60 50 20 50 100 200 500 1k Frequency (Hz) 2nd Harmonic 3rd Harmonic 17 2k
Patterns LQ™ 10P Horizontal Polar Patterns 6 dB per Division 0 30 o o o 0 o 30 -30 o o o -90 0 o o 90 -90 o o o 90 o -90 o -90 o -90 630 Hz o 0 o 30 o 60 -90 800 Hz o 90 -30 o o -60 o o -60 o o 60 -60 o o 90 -90 1 kHz 18 o -30 o 0 30 o o 500 Hz o 90 60 o 90 -30 o 30 o o 60 0 o -60 400 Hz 0 o -90 -30 60 -60 o o 90 315 Hz o o 60 30 o -60 o 30 o -30 o 0 o -30 o o 250 Hz o o 60 -60 200 Hz 30 30 o 60 -60
Patterns LQ™ 10P Horizontal Polar Patterns 6 dB per Division 0 30 o o o 0 o 30 -30 o o o -90 0 o o 90 -90 o o o 90 o -90 o -90 o -90 5 kHz o 0 o 30 o 60 -90 6.3 kHz o 90 -30 o o -60 o o -60 o o 60 -60 o o 90 -90 8 kHz 19 o -30 o 0 30 o o 4 kHz o 90 60 o 90 -30 o 30 o o 60 0 o -60 3.15 kHz 0 o -90 -30 60 -60 o o 90 2.5 kHz o o 60 30 o -60 o 30 o -30 o 0 o -30 o o 2 kHz o o 60 -60 1.
Patterns LQ™ 10P Horizontal Polar Patterns 6 dB per Division 0 o o 0 o 30 -30 o 30 o 60 60 -60 o o -30 o o -60 o o 90 o o o 90 -90 -90 16 kHz 12.
Patterns LQ™ 10P Vertical Polar Patterns 6 dB per Division 90 o o o 90 o 90 o 60 o 60 o 60 o 30 o o o o o -60 -60 o 200 Hz o o -90 -90 250 Hz 315 Hz o o 90 o 90 o 60 o 60 o 60 o 30 o 30 o 30 o 0 o 0 o 0 o -30 o -30 o -30 o -60 o -60 o -60 o -90 400 Hz o o -90 -90 500 Hz 630 Hz o o 90 o 90 o 60 o 60 o 60 o 30 o 30 o 30 o 0 o 0 o 0 o -30 o -30 o -30 o -60 800 Hz o -30 o -60 o o 0 -30 -90 -90 o 0 -30
Patterns LQ™ 10P Vertical Polar Patterns 6 dB per Division 90 o o o 90 o 90 o 60 o 60 o 60 o 30 o o o o o -60 -60 o 1.6 kHz o o -90 -90 2 kHz 2.5 kHz o o 90 o 90 o 60 o 60 o 60 o 30 o 30 o 30 o 0 o 0 o 0 o -30 o -30 o -30 o -60 o -60 o -60 o -90 3.15 kHz o o -90 -90 4 kHz 5 kHz o o 90 o 90 o 60 o 60 o 60 o 30 o 30 o 30 o 0 o 0 o 0 o -30 o -30 o -30 o -60 6.
Patterns LQ™ 10P Vertical Polar Patterns 6 dB per Division o o 90 90 o o 60 60 o o 30 30 o o 0 0 o o -30 -30 o o -60 -60 o o -90 -90 16 kHz 12.
Mounting Dimensions 24
INTRODUCTION The Crest LQ™10P features a biamped power section that provides 200 Watts peak dynamic power for the woofer and 70 Watts peak dynamic power for the compression driver tweeter, both with power amplifier compression. Offering a 10" premium long-throw woofer and the Crest HF™-1 compression driver, the LQ 10P provides line-level balanced inputs with volume control and loop-thru jacks.
INTRODUCCIÓN ESPA OL El LQ™10P de Crest cuenta con una sección biamplificada que provee 200 Watts de poder dinámico para el woofer y 70 Watts de poder dinámico para el tweeter de compresión, ambos con compresión del amplificador. Ofreciendo un woofer de 10" de tirada larga y un dirver de compresión Crest HF™-1, el LQ10P también ofrece entradas balanceadas de nivel línea con control de volumen y conexiones para circuitos (link).
PANEL TRASERO Caracter sticas del Panel Trasero 2 1 3 (1) FUSIBLE Esta unidad cuenta con protección de excesos y condiciones fallidas de corriente CA por medio de un fusible tipo ABC re rápida respuesta de 5 amperes. En el raro evento que la unidad vote el fusible, se debe desconectar de la toma de corriente y apagar (posición OFF), luego reemplazar el fusible con un fusible tipo ABC re rápida respuesta de 5 amperes y 250 Voltios SOLAMENTE.
PANEL FEATURES Front Panel Features 5 4 7 6 (4) LED DE ENCENDIDO Este se ilumina cuando los electrónicos del preamplificador reciben corriente, el interruptor de encendido está en la posición de encendido y el cable de corriente está conectado a una fuente de corriente. (5) ENTRADA DE LŒNEA/A TRAV S Las conexiones de entrada y salida están cableadas en paralelo para que puedan ser usadas por otros aparatos.
INSTRUCCIONES DE OPERACIÓN PRECAUCIONES Esta unidad debe ser desconectada de la toma de corriente CA antes de realizar cualquier trabajo en ella.Todo servicio debe ser llevado a cabo por personal calificado. La trampa de calor en la parte trasera puede estar caliente al tacto. Nunca se debe cubrir o bloquearle la ventilación. NUNCA se deben conectar las entradas del LQ 10P a la salida de un amplificador. Las entradas han sido diseñadas para ser alimentadas por señales de nivel de línea.
VOLANDO EL LQ 10P Cuidado: El suspender o volar las LQ 10P de Crest es un proceso que debe ser llevado a cabo por un ingeniero certificado. Información importante de montaje del sistema de parlantes LQ 10P de Crest: Cuidado: Antes de intentar suspender este modelo de parlantes, consulta a un ingeniero de estructuras calificado. Los parlantes se pueden caer de suspensiones incorrectas, resultando en daños al equipo y personales.
VOLANDO EL LQ 10P un sistema entero no es la manera de maximizar la capacidad del sistema de sonido. La tercera aguja en el cable de corriente NUNCA debe ser quitada, esto compromete seriamente la seguridad del sistema. Nota Especial Para Instalaciones Permanentes Cuando se instale la LQ 10P de Crest, se recomienda consultar un electricista calificado para asegurarse que todos los cableados de CA van de acuerdo con los códigos y regulaciones locales.
VOLANDO EL LQ 10P Los amplificadores del LQ 10P están equipados con un sistema de prevención de saturación y un LED que indica que este ha sido activado. Si el sonido parece estar seriamente comprimido, verifica este indicador LED y si indica más de un parpadeo ocasional, entonces el nivel de la mezcladora (o el control de volumen del LQ 10P) debe ser reducido.
PROBLEMAS No Hay Salida Antes que nada hay que asegurarse que la unidad cuenta con corriente eléctrica y que está encendida. El LED de encendido (4) debe estar iluminado. Si no lo está, hay que verificar que el interruptor de encendido/apagado (3) está en la posición de encendido (ON). Hay que verificar el cable IEC y la conexión de corriente (2), asegurándose que está completamente conectado en ambos lados.
VOLANDO EL LQ 10P Hay que verificar que se estén usando las entradas correctas (5) y no la entrada de micro (8) para señales de nivel de línea. Hay que verificar también que no se ha conectado un amplificador a las entradas del LQ 10P. Si se está utilizando una extensión de corriente para llevar electricidad a la unidad ¿Es de suficiente capacidad de corriente y no está alimentando a ninguna otra unidad? Ver LLEVANDO CORRIENTE AL LQ 10P para más detalles.
VOLANDO EL LQ 10P pueden limpiar los excedentes con tela. Para que luzca de la mejor manera y se proteja aconsejamos aplicar un producto como Armour-All® o WD-40® a la superficie plástica del gabinete solamente. Nótese que la superficie quedará resbalosa después de la aplicación del producto, para minimizar este efecto recomendamos pasarle un paño seco varias veces. Si la rejilla perdiera color o muestra manchas blancas se puede usar un limpiador casero como Fantastic® o 409® para limpiar la rejilla.
VOLANDO EL LQ 10P y a capacidad completa de salida. El sistema debe utilizar un woofer de 10" de largo alcance y un tweeter de fuente comprimida HF-1. La forma de cobertura será de 90˚ en plano horizontal y 45˚ en plano vertical. El sistema de parlantes biamplificado debe tener un grupo de entradas de impedancia media consistiendo de un combo femenino XLR y 1/4" TRS plug, y un XLR masculino, en el panel trasero, todas conectadas en paralelo.
Installation FRAN AIS La Crest LQ™10P possède une section bi-amplification lui fournissant 200 watts peak pour le haut-parleur et 70 Watts peak pour le moteur de compression, toutes deux munies du système de protection Peavey DDT™. Equipée d’un haut-parleur 10" longue-portée et du moteur de compression Crest HF™-1, la LQ 10P offre des entrées ligne symétriques ainsi qu’un contrôle de volume et une sortie pour chainage d’enceintes.
PANEL CARACTÉRISTIQUES Rear Panel Features 2 1 3 (1) FUSIBLE Votre unité est protégée par un fusible de type ABC de 5 Ampères. Dans le cas ou celui-ci grille, mettre votre unité hors tension (déconnecter le cable d’alimentation), puis remplacer le fusible par un équivalent de même valeur (5A-250V). Assurezvous de repositionner correctement le support de fusible. Mettez le volume de votre unité au minimum, puis reconnecter votre enceinte à sa source d’alimentation. Mettre votre unité sous tension.
PANEL FEATURES Front Panel Features 5 4 7 6 (4) LED D ALIMENTATION S’illumine lorsque l’appareil est sous tension. (5) ENTREES/SORTIES PRIMAIRES Les entrées sont placées en parallèle afin de faciliter le chaînage d’enceintes. Le niveau d’"entrée" est le même que le niveau de "sortie" est aucune isolation n’est réalisée entre les différents connecteurs. Les entrées sont de type symétrique et ultra-silencieuses.
MANUEL D’UTILISATION ATTENTION Si il est nécessaire d’enlever le panneau arrière (ou de le remettre en place), les vis de fixations doivent être dévissées (vissées) en enlevant la grille et les haut-parleurs pour accéder aux écrous et les empêcher de tourner par la face avant de votre enceintes.Votre unité doit être déconnectée de la source d’alimentation électrique. Nous vous conseillons de faire entretenir votre unité par un technicien qualifié.
SUSPENDRE LA LQ-10P ATTENTION: Suspendre des enceintes doit être supervisé par un personnel qualifié. Informations importantes pour suspendre une Crest LQ-10P : Attention: Consultez un ingénieur du batiment (Stucture) avant tout! Une mauvaise installation peut résulter en la chute d’une enceinte, pouvant entrainer de graves accidents et détruire du matériel.Toujours utilisez du matériel de suspension adéquate. Ne jamais suspendre des enceintes en dessous les unes des autres.
SUSPENDRE LA LQ-10P Bien qu’un jack 2-connecteurs (T-S) sera utilisable, le circuit d’entrée symétrisant le signal, un jack 3-connecteurs (R-T-S) ou une XLR aura un rendement plus efficace. En cas de problème d’interférences, il peut-être utile de modifier la référence de masse de votre signal en déconnectant la masse de l’entrée symétrique du cable de celle du chassis de votre enceinte (Groung Lift). L’utilisation de câbles de haute qualité est recommandée avec la LQ-10P.
TROUVER L ORIGINE DE PROBLEMES COURANTS APPLICATIONS Les LQ-10P sont adaptées à de très nombreuses applications, telles que karaoke, conférence, diffusion de musique,... De plus, vous pouvez grace à l’adaptateur ‘Monitor Stand’ la transformer en un retour de scène amplifié. Vous pouvez y envoyer aussi bien un signal de sortie de console de mixage, de lecteur CD (ou autre) ou d’un micro. Aucun signal en sortie: Assurez-vous que l’unité est branchée et sous-tension. La LED d’alimentation doit être illuminée.
MAINTENANCE La LQ-10P possède un équaliseur fixe interne destiné à étendre et assouplir la réponse du haut-parleur. Un filtre anti-infrabasses est inclu et la réponse du système est aussi plate que possible. Si le signal alimentant l’enceinte a été sur-équalisé dans les basses, la LQ-10P peut entrer en distorsion lors de hauts niveaux de pression accoustique. N’équalisez pas excessivement les basses à partir de vos appareils externes (mixeurs, équaliseurs rack).
SUSPENDRE LA LQ-10P DESCRIPTION L’enceinte Crest LQ-10P est une enceinte amplifiée destinée à fournir des perfomances maximales à partir d’un système compact. Capable de niveaux de pression accoustique de 120 dB peak, elle peut produire un niveau de basses fréquences conséquent. L’enceinte trapézoïdale est réalisée en polypropylène résistant par injection, et possède une grille de protection métallique enrobée de plastique.
DEUTSCH Der Crest LQ™10P ist mit einer Endstufe mit zwei Verstärkern ausgestattet, die eine dynamische Spitzenleistung von 200 Watt für den Woofer und eine dynamische Spitzenleistung von 70 Watt für den Hochtöner mit Kompressionstreiber liefert – und zwar jeweils mit Verstärkerschutzschaltung.
FUNKTIONEN AN DER RÜCKSEITE Funktionen an der RÜckseite 2 1 3 (1) SICHERUNG Das Gerät ist durch eine flinke ABC-Sicherung (5 Ampere) vor Überlastungen und Störungen (Wechselstromanschluss) gesichert. Sollte die Sicherung tatsächlich einmal durchbrennen (was selten geschieht), überprüfen Sie zunächst, ob das Gerät von der Stromversorgung getrennt und ausgeschaltet ist (Position OFF). Ersetzen Sie dann die Sicherung NUR durch eine flinke Sicherung (5 Ampere und 250 V Wechselstrom).
PANEL FEATURES Front Panel Features 5 4 7 6 (4) POWER-LED Diese LED leuchtet auf, wenn die Elektronik des Vorverstärkers mit Strom versorgt wird. Zudem sollte sie aufleuchten, wenn sich der Ein/Aus-Schalter auf der Position ON befindet und das Wechselstromkabel angeschlossen und in eine Steckdose gesteckt ist. (5) LINE IN/THRU Die Eingangs- und Ausgangsklinken sind parallel geschaltet, sodass das Audio-Eingangssignal durch Hintereinanderschaltung an andere Geräte angeschlossen werden kann.
BETRIEBSANLEITUNG ACHTUNG! Bevor jegliche Art von Arbeiten am Gerät durchgeführt werden, muss es von der Wechselstromquelle getrennt werden. Lassen Sie sämtliche Wartungsarbeiten von qualifizierten Kundendiensttechnikern durchführen. Der Kühlkörper an der Rückwand kann heiß werden, daher darf er nicht berührt werden. Der Kühlkörper darf nicht blockiert oder abgedeckt werden, da ansonsten die Belüftung beeinträchtigt wird. Schließen Sie die Eingänge des LQ 10P NICHT an den Ausgang eines Verstärkers an.
FLIEGEN DES LQ 10P Achtung: Das Aufhängen oder Fliegen des Crest LQ 10P muss von einem zugelassenen Bauingenieur durchgeführt werden. Wichtige Sicherheitsinformationen für die Montage von Crest LQ 10P-Lautsprechersystemen: Achtung: Bevor Sie versuchen, diese Lautsprechermodelle aufzuhängen, muss ein zugelassener Bauingenieur zu Rate gezogen werden.Werden die Lautsprecher nicht korrekt aufgehängt, können sie herunterfallen und schwere Personen- und Sachschäden verursachen.
FLIEGEN DES LQ 10P VERSORGUNG DES CREST LQ 10P MIT WECHSELSTROM Der LQ 10P wird mit einem IEC-Anschlussnetzkabel (Wechselstrom) von ca. 2,40 m Länge geliefert.Wird ein Verlängerungskabel verwendet, muss sichergestellt werden, dass es nicht länger als notwendig ist und über die ausreichende Stromkapazität verfügt, um die Sicherheit zu gewährleisten. Ein Hochstromkabel in der geeigneten Länge steigert die Leistungsabgabe der internen Verstärker des LQ 10P.
FLIEGEN DES LQ 10P Für den Einsatz mit dem LQ 10P werden qualitativ hochwertige Kabel empfohlen, da bei diesen in der Regel Abschirmung und Material besser sind und sie eine längere Haltbarkeit und Zuverlässigkeit bieten. Empfohlen wird auch, am Eingang des LQ 10P einen gewissen Spielraum zu lassen und die Kabel abzukleben oder sie unter einem Kabelschutz zu verlegen, sodass niemand darüber stolpert oder das Gerät am Kabel herabzieht, wenn es auf einem Ständer montiert ist.
FEHLERSUCHE Die LINK-Klinken (10) können ebenfalls zum Anschließen mehrerer LQ 10P oder einem anderen Power-Gerät der LQ-Serie verwendet werden, wobei die Lautstärke bequem über den Lautstärkeregler eines einzigen Gerätes geregelt werden kann. Schließen Sie ein gut geschirmtes Anschlusskabel mit zwei 1/4"-Kopfhörersteckern von der Link-Out-Klinke des Gerätes an, dessen Eingang an die Signalquelle angeschlossen ist, und schließen Sie dann dieses Kabel an die Link-In-Klinke des anderen Gerätes an.
FLIEGEN DES LQ 10P Brummen oder Summen Dies kann mit der Wechselstrom-Steckdose zusammenhängen. Stecken Sie den LQ 10P versuchsweise in eine andere Wechselstrom-Steckdose.Wird für den Mischpult ein anderer Schaltkreis bzw. Überlastschalter verwendet als für den LQ 10P, kann dies Probleme durch Brummen verursachen. Stellen Sie sicher, dass für die Signalleitung zum LQ 10P geschirmte Kabel verwendet werden. Lautsprecherkabel mit 1/4"- oder XLR-Steckern sind sehr anfällig für Brummen.
FLIEGEN DES LQ 10P erforderlich sind, um eine ausreichende Schallleistung oder Schallübertragung zu erzielen.Versuchen Sie in diesem Fall, die Mischpultpegel ein wenig herunterzuregeln, um einen klareren Sound zu erzielen. Sollten Sie sämtliche aufgeführten Punkte sowie weitere Möglichkeiten im Rahmen der Sicherheit überprüft haben und dennoch weitere Probleme mit dem System auftreten, notieren Sie sich bitte sorgfältig sämtliche Bedingungen und wenden Sie sich an Ihren Crest-Händler um Unterstützung.
FLIEGEN DES LQ 10P berpr fung der Sicherheit der Beschlagteile Nach den ersten Einsatzmonaten und auch regelmäßig danach muss überprüft werden, ob die Beschlagteile des LQ 10P fest angezogen sind, so etwa die Schrauben der Rückseite und die Schrauben, mit denen die Schallwand und die hintere Box aneinander befestigt sind. Da das Gerät in hohem Maß Vibrationen ausgesetzt ist, können sich diese Teile mit der Zeit lösen.
FLIEGEN DES LQ 10P Das Power-Lautsprechersystem mit zwei Verstärkern verfügt über eine Gruppe von mittelohmigen Eingangssteckern, und zwar über einen weiblichen Combo-XLR-Stecker und einen 1/4"-Kopfhörerklinkenstecker sowie einen XLR-Stecker, die sich auf der Rückseite befinden und parallel geschaltet sind. Es sind eine Link-Out- und eine Link-In-Klinke vorhanden, und neben der Eingangsklinkengruppe ist ein Pegelregler vorhanden.
NOTES 58
WARRANTY STATEMENT CREST AUDIO LIMITED WARRANTY Effective Date: November 1, 2000 What This Warranty Covers Your Crest Audio Warranty covers defects in material and workmanship in Crest Audio products purchased and serviced in the U.S.A.
Features and specifications subject to change without notice. Crest Audio Inc. • 16-00 Pollitt Drive • Fair Lawn, NJ 07410 USA TEL: 201.909.8700 • FAX: 201.909.8744 • www.crestaudio.com ©2003 80304921 Printed in the U.S.A.