Crestron C2N-HBLOCK Multi-Type Network Distribution Block Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc.
Crestron C2N-HBLOCK Multi-Type Network Distribution Block Contents Multi-Type Network Distribution Block: C2N-HBLOCK 1 Introduction......................................................................................1 Specifications.........................................................................2 Physical Description ..............................................................2 Industry Compliance..............................................................5 Installation and Wiring ..........
Crestron C2N-HBLOCK Multi-Type Network Distribution Block Multi-Type Network Distribution Block: C2N-HBLOCK Introduction The C2N-HBLOCK is a Crestron control network (Cresnet) multiple connector type, network distribution block that provides wiring for up to 15 devices and/or peripherals. The C2N-HBLOCK provides 24 volts direct current (VDC), Cresnet Y and Z data signals, and ground through three different types of Cresnet connectors.
Multi-Type Network Distribution Block Crestron C2N-HBLOCK Specifications The table below provides a summary of specifications for the C2N-HBLOCK. Specifications of the C2N-HBLOCK SPECIFICATION DETAILS Height: 1.27 in (3.23 cm) Width: 5.55 in (14.10 cm) Depth: 3.30 in (8.38 cm) Weight: 0.68 lb (0.31 kg) * Dimensions & Weight * The weight listed is for the C2N-HBLOCK and all supplied 4-pin connectors.
Crestron C2N-HBLOCK Multi-Type Network Distribution Block C2N-HBLOCK Physical Views 1 2 3 24 Y Z G 4 5 24 Y Z G 6 CRESTRON A B C D 8 24 Y Z G POWER Y Z a b c 3.30 in (8.38 cm) E 24 24 24 Y Y Y Z Z Z G G G C2N-HBLOCK 7 24 Y Z G 4.30 in (10.92 cm) ALL CONNECTORS ARE IN PARALLEL 5.55 in (14.10 cm) Front Panel View 6.55 in (16.64 cm) Bottom View C000000 ZA11736 MADE IN THE U.S.A. C2N-HBLOCK N11785 1.33 in (3.
Multi-Type Network Distribution Block Crestron C2N-HBLOCK C2N-HBLOCK Ports The C2N-HBLOCK contains three types of ports that are connected in parallel. The eight 3.5mm, 4-pin connectors (labeled 1, 2, 3, 4, 5, 6, 7 and 8) and the five 5mm, 4-pin connectors (labeled A, B, C, D and E) are used to connect the C2N-HBLOCK to other four-wire Cresnet devices. The three 6-pin RJ11 modular ports (labeled a, b and c) are used to connect the C2N-HBLOCK to modular devices in the Cresnet system.
Crestron C2N-HBLOCK Multi-Type Network Distribution Block anything other than dimly illuminated, refer to “Y and Z LED Illumination” on page 9 for further information. Industry Compliance As of the date of manufacture, the C2N-HBLOCK has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785).
Multi-Type Network Distribution Block Crestron C2N-HBLOCK Detach Mounting Plate 2. For further instructions, refer to the latest revision of the CNXRMAK Installation Guide (Doc. 8156). This document can be obtained from the Downloads | Product Manuals section of the Crestron website (www.crestron.com). Network Wiring CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. NOTE: For larger networks (i.e.
Crestron C2N-HBLOCK Multi-Type Network Distribution Block When calculating the wire gauge for a particular Cresnet run, the length of the run and the power factor of each network unit to be connected must be taken into consideration. If Cresnet units are to be daisy-chained on the run, the power factor of each unit to be daisy-chained must be added together to determine the power factor of the entire chain.
Multi-Type Network Distribution Block Crestron C2N-HBLOCK connection into the Cresnet connector and tighten the retaining screw. Repeat the procedure for the other three conductors. Connecting the C2N-HBLOCK to Cresnet Devices CAUTION: Do not connect or daisy-chain more than one power input (power pack or power supply) to the C2N-HBLOCK. Multiple power inputs may damage one or more power packs and/or power supplies. CAUTION: Crestron modular cables are rated for a maximum of two (2) amperes.
Crestron C2N-HBLOCK Multi-Type Network Distribution Block Problem Solving General Troubleshooting The table after this paragraph provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. C2N-HBLOCK General Troubleshooting POSSIBLE CAUSE(S) CORRECTIVE ACTION C2N-HBLOCK is not receiving power. Y and Z data wires incorrect. Confirm that proper power is supplied to the C2N-HBLOCK (24 VDC regulated).
Multi-Type Network Distribution Block Crestron C2N-HBLOCK Further Inquiries If after reviewing this Operation & Installation Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: • In the US and Canada, call Crestron’s corporate headquarters at 1-888-Crestron [1-888-273-7876]. • In Europe, call Crestron International at +32-15-50-99-50. • In Asia, call Crestron Asia at +852-2341-2016.
Crestron C2N-HBLOCK Multi-Type Network Distribution Block Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 8157A 05.03 Specifications subject to change without notice.
