- Creston Power Supply Specification Sheet

ManualsBrandsCrestron electronic ManualsPower SupplyGLA-PWSI50

GLA-PWSI50

Crestron Electronics, Inc. Installation Guide – DOC. 6747A

15 Volvo Drive Rockleigh, NJ 07647 (2022674)

Functional Summary

The GLA-PWSI50 is a 50 Watt Cresnet

Power Supply

designed for use with a Crestron

Green Light™ system,

or anywhere a wall-mountable Cresnet power supply is

needed. It is compatible with any line voltage from 100 to

240 Volts, 50 or 60 Hz.

The GLA-PWSI50 mounts conveniently over the front of

an electrical box, with all connections made inside the

box via flying leads using terminal block connectors. An

adapter plate is included for installation over a 1 or

2-gang UK or Euro style electrical box. Without the

adapter plate, the GLA-PWSI50 may be mounted over a 4

inch square or 2-gang US electrical box.

• 50 Watt Cresnet power supply

• Powers the IPAC and other Cresnet devices

• Provides backup power for Crestron Green Light

cabinets

• Compatible with 100 to 240 VAC mains

• Mounts to a 1 or 2-gang UK (BS 4662) or Euro

(DIN 49073) electrical box

• Also compatible with 4 inch square or 2-gang US

electrical boxes

GLA-PWS50 (shown with Adapter Plate) Physical View

Specifications

GLA-PWSI50 Specifications

SPECIFICATION DETAILS

Output Power

Ripple/Noise

50 Watts (2.1 Amps) @ 24 Volts

DC, regulated, limited power

source

<1%

Power Requirements

Input

0.6 Amps @ 100-240 Volts AC,

50/60 Hz

Enclosure Metal construction, 1- or 2-gang

(BS4662 UK or DIN 49073)

backbox, includes adapter plate

Environmental

Temperature

Humidity

Heat Dissipation

0° to 40°C (32° to 104°F)

10% to 90% RH

(non-condensing)

26 BTU/Hr

Dimensions

(without adapter plate)

Height

Width

Depth

10.16 cm (4.00 in)

14.09 cm (5.55 in)

5.76 cm (2.27 in)

Weight 0.54 kg (1.2 lbs)

Tel: 888.CRESTRON 02.09

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Summary of content (8 pages)

PAGE 1
GLA-PWSI50 Functional Summary The GLA-PWSI50 is a 50 Watt Cresnet® Power Supply designed for use with a Crestron® Green Light™ system, or anywhere a wall-mountable Cresnet power supply is needed. It is compatible with any line voltage from 100 to 240 Volts, 50 or 60 Hz. The GLA-PWSI50 mounts conveniently over the front of an electrical box, with all connections made inside the box via flying leads using terminal block connectors.
PAGE 2
50 Watt Cresnet Power Supply Crestron GLA-PWSI50 Industry Compliance As of the date of manufacture, the GLA-PWSI50 has been tested and found to comply with specifications for CE marking. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
Crestron GLA-PWSI50 50 Watt Cresnet Power Supply Application The following diagram shows a GLA-PWSI50 module in a typical application. GLA-PWSI50 in a Lighting Application Installation Guide – DOC.
PAGE 4
50 Watt Cresnet Power Supply Crestron GLA-PWSI50 Connectors, Controls & Indicators Physical Description # This section provides information on the connections, controls and indicators available on the GLA-PWSI50. CONNECTORS, CONTROLS & INDICATORS 1 LINE POWER (3) 152 mm flying leads, 0.75 2 mm , line power input Line (brown), neutral (blue), and ground (green/yellow) connections 2 OUTPUT (2) 152 mm flying leads, 0.
PAGE 5
Crestron GLA-PWSI50 50 Watt Cresnet Power Supply Adapter Plate Usage Preparation The GLA-PWSI50 comes with an adapter plate for mounting the power supply on a BS4662 UK backbox or a 1- or 2-gang DIN 49073 backbox. 1. Route the line and control wires from the backbox through the opening on the adapter plate as shown in the following diagram. Route Wires Through Adapter Plate (1-Gang DIN 49073 Backbox Shown) LOC. USE WITH A 1-GANG BS 4662 UK BACKBOX Top: (1) M3.5 (Not Supplied) Bottom: (1) M3.
PAGE 6
50 Watt Cresnet Power Supply Crestron GLA-PWSI50 Installation CAUTION: Only use the specified type of fuse when replacing a blown fuse. Failure to do so may cause damage to the GLA-PWSI50. The GLA-PWSI50 mounts to the adapter plate using the four included screws. Refer to the following diagram when installing the GLA-PWSI50. NOTE: Ensure that the wires will not be pinched during the installation process by pushing the wires into the backbox. FUSE TYPE: 5 x 20mm 3.15A Time Lag 5.
PAGE 7
50 Watt Cresnet Power Supply Crestron GLA-PWSI50 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PAGE 8
50 Watt Cresnet Power Supply Crestron GLA-PWSI50 This page is intentionally left blank. 8 • Wall Mount 50 Watt Cresnet Power Supply: GLA-PWSI50 Installation Guide – DOC.