Crestron SRD-SPL-4 Four-Way Amplified Splitter Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2008 Crestron Electronics, Inc.
Crestron SRD-SPL-4 Four-Way Amplified Splitter Contents Four-Way Amplified Splitter: SRD-SPL-4 1 Introduction................................................................................................................................1 Block Diagram.............................................................................................................2 Specifications...............................................................................................................2 Included Items ...
Crestron SRD-SPL-4 Four-Way Amplified Splitter Four-Way Amplified Splitter: SRD-SPL-4 Introduction The SRD-SPL-4 is a high quality amplified splitter optimized to split a single antenna signal to feed up to four satellite radio tuners as part of a Crestron® XM or SIRIUS® satellite radio distribution network. Its built-in line amplifier is rated to provide 8 dB (minimum) of gain in the satellite radio band (2320-2345 MHz), and is powered from the DC bias voltage (4.5 VDC to 6.
Four-Way Amplified Splitter Crestron SRD-SPL-4 Block Diagram The following diagram illustrates a typical application using the SRD-SPL-4 splitter. SRD-SPL-4 Block Diagram Specifications Following are specifications for the SRD-SPL-4. SRD-SPL-4 Specifications SPECIFICATION Splitter gain @ 2.
Crestron SRD-SPL-4 Four-Way Amplified Splitter SRD-SPL-4 Specifications (Continued) SPECIFICATION Humidity DETAILS 0% to 98% RH (non-condensing) Overall dimensions: Height Width Depth 0.88 in 3.75 in 2.82 in (2.24 cm) (9.53 cm) (7.17 cm) Included Items The items included in the SRD-SPL-4 are listed and shown below.
Four-Way Amplified Splitter Crestron SRD-SPL-4 Industry Compliance As of the date of manufacture, the SRD-SPL-4 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Installation Installation of the SRD-SPL-4 splitter consists of the following. Refer also to the “Block Diagram” on page 2. • Attach the RG-6 cable from the antenna to the port labeled IN on the splitter.
Crestron SRD-SPL-4 Four-Way Amplified Splitter Problem Solving Troubleshooting The table after this paragraph provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. SRD-SPL-4 Installation Troubleshooting TROUBLE POSSIBLE CAUSES CORRECTIVE ACTION No signal reception.
Four-Way Amplified Splitter Crestron SRD-SPL-4 SRD-SPL-4 Installation Troubleshooting (Continued) TROUBLE Limited reception or channels available for XM and/or SIRIUS tuners. POSSIBLE CAUSES CORRECTIVE ACTION Problem with tuner card. Ensure that the tuner card is registered/activated.
Crestron SRD-SPL-4 Four-Way Amplified Splitter Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Installation Guide – DOC. 6727A (2021581) 08.08 Specifications subject to change without notice.
