Crestron CWD1015 Two-Way RF Transceiver Module Operations Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2007 Crestron Electronics, Inc.
Crestron CWD1015 Two-Way RF Transceiver Module Contents Two-Way RF Transceiver Module: CWD1015 ............................................. 1 Introduction................................................................................................................................1 Functions and Features ................................................................................................1 Specifications .........................................................................................
Crestron CWD1015 Two-Way RF Transceiver Module Two-Way RF Transceiver Module: CWD1015 Introduction Functions and Features The CWD1015 (hereafter referred to as “module”) is a two-way radio frequency (RF) module that utilizes the 2.4 GHz frequency band to communicate with other devices. The module operates according to the IEEE 802.15.4 specification and can be configured to minimize the possibility of interference with other devices.
Two-Way RF Transceiver Module Crestron CWD1015 Specifications The table below is a summary of specifications for the CWD1015. Specifications of the CWD1015 SPECIFICATION DETAILS Power Requirements 0.75 Watts (3.3VDC @ 0.250A) Operating Frequency 2400 MHz to 2483.6 MHz (802.15.4 compliant) Operating Ranges¹ Minimum Distance 3 ft Maximum Distance Indoors (without repeater device) 100 ft Available Channels 16 (numbered 11 through 26 per 802.15.
Crestron CWD1015 Two-Way RF Transceiver Module CWD1015 Detail Views 1.00 in (2.54 cm) 0.20 in (0.51 cm) 1.08 in (2.74 cm) Ports The module contains 24 solder points and one antenna port. Refer to the diagrams and descriptions that follow. Power/I-O Twenty-four solder points provide power to the module as well as serial communications between the module and wired devices. Refer to the following table for pin assignments of the module interface connector.
Two-Way RF Transceiver Module Crestron CWD1015 Antenna This U.FL/MMC antenna port is located at edge of the circuit board for attaching an antenna. APPROVED ANTENNAS: The CWD1015 antenna interface has a unique coupling designed to ensure that no antenna other than the one supplied shall be used with the device. Replacement antennas may be purchased from Crestron according to the following description: Part Number: Crestron #4504627 Description: ANTENNA, PCB ASSY 2.4 - 2.5 Ghz U.FL connect .
Crestron CWD1015 Two-Way RF Transceiver Module Section 7.1.4 of RSS-GEN This device has been designed to operate with the antenna(s) listed below, and having a maximum gain of 1.9 dBi. Antennas not included in this list or having a gain greater than 1.9 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Part Number Crestron #4504627 Frequency 2.4-2.
Two-Way RF Transceiver Module Crestron CWD1015 Setup Hardware Hookup Refer to the hookup diagram below, which shows the connections made to the module. Complete the connections in any order. NOTE: To prevent unit-to-unit RF interference, multiple modules operating at the same frequencies should not be installed within three to five feet of each other.
Crestron CWD1015 Two-Way RF Transceiver Module This page intentionally left blank Operations Guide - DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide - DOC. 6659 01.08 INTERNAL USE ONLY Specifications subject to change without notice.
