Crestron HTT-B10EX ® infiNET EX TableTop Controller Operations Guide
Regulatory Compliance As of the date of manufacture, the HTT-B10EX and HTTI-B10EX has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Industry Canada (IC) Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Crestron HTT-B10EX infiNET EX TableTop Controller Contents infiNET EX TableTop Controller: HTT-B10EX 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Specifications ..............................................................................................................
Crestron HTT-B10EX infiNET EX TableTop Controller infiNET EX TableTop Controller: HTT-B10EX Introduction The HTT-B10EX and HTTI-B10EX provide a simple, convenient wireless controller for lighting, home automation, and entertainment in the home or office. Two-way infiNET EX™ wireless operation supports true feedback, allowing lighting and security settings to be checked and changed with confidence from any room.
InfiNET EX TableTop Controller Crestron HTT-B10EX Multifunction Push buttons Ten simple push buttons provide just the right amount of control without clutter or complication—perfect for most applications. For situations requiring a little more, each button can be configured to enable up to three separate functions simply by tapping, double-tapping or holding the button. “Shift key” functionality is even possible, allowing any button to be held while pressing another.
Crestron HTT-B10EX infiNET EX TableTop Controller The HTT-B10EX works together with other infiNET EX devices like our Cameo Wireless In-Wall Dimmers and Switches, communicating with a Crestron control system via the CEN-RFGW-EX infiNET EX Wireless Gateway (sold separately). Up to 100 infiNET EX devices may coexist on a single wireless network, and every device that is added to the network effectively increases the range and stability of the entire network by providing multiple redundant signal paths*.
Crestron HTT-B10EX InfiNET EX TableTop Controller Specifications Specifications for the HTT-B10EX are listed in the following table. HTT-B10EX Specifications SPECIFICATION DETAILS Backlight White LED light pipe backlight for button engraving; software adjustable intensity, auto-dimmable Movement Sensor Vibration sensor wakes unit from sleep mode if operating on battery Wireless RF Transceiver infiNET EX 2-way RF, 2.4 GHz ISM Channels 11-26 (2400 to 2483.5 MHz), default channel 15; IEEE 802.15.
Crestron HTT-B10EX infiNET EX TableTop Controller HTT-B10EX Specifications (Continued) SPECIFICATION DETAILS Available Models (120 Vac) HTT-B10EX-B-T infiNET EX TableTop Controller, Black Textured HTT-B10EX-W-T infiNET EX TableTop Controller, White Textured International Version (230 Vac) HTTI-B10EX-B-T infiNET EX TableTop Controller, Black Textured HTTI-B10EX-W-T infiNET EX TableTop Controller, White Textured Included Accessories Power Pack 12 Volt Power Pack Available Accessories B10-BTN(B/W
Crestron HTT-B10EX InfiNET EX TableTop Controller HTT-B10EX Overall Dimensions (Top View) 1 4.69 in (120 mm) 2 2 3 HTT-B10EX Overall Dimensions (Side View) 1.46 in (38 mm) HTT-B10EX Overall Dimensions (Rear View) 4 3.60 in (92 mm) 6 • infiNET EX TableTop Controller: HTT-B10EX Operations Guide – DOC.
Crestron HTT-B10EX infiNET EX TableTop Controller Connectors, Controls, and Indicators # CONNECTORS, CONTROLS, AND INDICATORS 1 LIGHT SENSOR 2 LED INDICATORS 3 BUTTONS 4 POWER DESCRIPTION Photo sensor for control of auto-dimming function. FEEDBACK - (10) White LED light pipes, one per button; Programmable, autodimmable, adjustable intensity, 10 blinking patterns. BAR GRAPH – (2) Five step bar graphs utilizing the 10 feedback indicators.
InfiNET EX TableTop Controller Crestron HTT-B10EX Setup Identity Code NOTE: The latest software can be downloaded at www.crestron.com/software. Every HTT-B10EX communicating via RF with a Crestron control system through a wireless gateway requires a unique RF ID. The RF ID is a 2-digit hexadecimal number that can range from 03 to 6C. The RF ID of the unit, set using Crestron Toolbox™, must match the RF ID specified in the SIMPL Windows program.
Crestron HTT-B10EX infiNET EX TableTop Controller HTT-B10EX Button Installation Hardware Hookup The only connection to the HTT-B10EX is for the included 12 Volt power pack. When connecting the HTT-B10EX, consider the following: • Use Crestron power supplies for Crestron equipment. • The included cable cannot be extended. Hardware Connections for the HTT-B10EX 12V 0.5A: ac Power Pack NOTE: The HTT-B10EX will not charge rechargeable AA batteries. Operations Guide – DOC.
Crestron HTT-B10EX InfiNET EX TableTop Controller Setup Prior to using the HTT-B10EX as part of a Crestron system, it must be configured for use on an infiNET EX network. HTT-B10EX Button Reference Button #1: Enables/Disables Manner Mode 1 3 5 7 9 2 4 6 8 10 LED #8: Indicates infiNET EX link status Joining an infiNET EX Network Before an HTT-B10EX can be used in a lighting system, it must first join an infiNET EX network by being acquired by an infiNET EX gateway.
Crestron HTT-B10EX infiNET EX TableTop Controller Leaving an infiNET EX Network To leave a network, simply place the INET-CBDEX into Acquire mode (step 2 above) when there is no gateway in Acquire mode. Verifying Communications Status To check the communication status of the device, tap either the left or right top button three times then press and hold it down (tap-tap-tap-press+hold) for less than 2 seconds. The top LED indicates the communication status. Refer to the following table for details.
InfiNET EX TableTop Controller Crestron HTT-B10EX Local Button Feedback Use SIMPL Windows to enable/disable local button feedback. Local button feedback provides positive confirmation for any button press. When enabled, the LED next to the button being pressed will light for as long as the button is pressed. When the button is released, feedback is governed by the program. When local button feedback is disabled (the default), button feedback is always governed by the program.
Crestron HTT-B10EX infiNET EX TableTop Controller Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (or device).
InfiNET EX TableTop Controller Crestron HTT-B10EX Programs and Firmware Program or firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron Web site as new features are developed after product releases. One has the option to upload programs via the programming software or to upload and upgrade via the Crestron Toolbox.
Crestron HTT-B10EX infiNET EX TableTop Controller Operation The behavior of the HTT-B10EX will differ depending upon whether it is powered via the included 12 volt power pack or via two AA batteries. When powered from the 12 volt power pack, the unit will behave much like a wired keypad, constantly communicating with the control system via the gateway.
Crestron HTT-B10EX InfiNET EX TableTop Controller Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. HTT-B10EX Troubleshooting TROUBLE Device does not function. POSSIBLE CAUSE(S) CORRECTIVE ACTION Device is not receiving power from a Crestron power source. Use the provided Crestron power source. Verify connections.
Crestron HTT-B10EX infiNET EX TableTop Controller Further Inquiries To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of Crestron worldwide offices at www.crestron.com/offices. To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.
InfiNET EX TableTop Controller Crestron HTT-B10EX Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron HTT-B10EX infiNET EX TableTop Controller This page is intentionally left blank. Operations Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 6995 (2018330) 10.13 Specifications subject to change without notice.
