Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. 2005 Crestron Electronics, Inc.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Contents Shade & Drape DC Motor Controller: C2N-SDC-DC 1 Introduction.................................................................................1 Features & Functions........................................................1 Specifications....................................................................2 Physical Description .........................................................3 Industry Compliance.........................................
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Shade & Drape DC Motor Controller: C2N-SDC-DC Introduction Features & Functions The Crestron C2N-SDC-DC is a shade and drape DC motor control Cresnet® slave module designed to control two 2-wire bi-directional DC motors that drive shades and drapes. The C2N-SDC-DC is specifically designed for the Cresnet control network and functions as part of a complete Crestron control/automation system.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC lockout timer that shuts the motor off for a brief time before allowing the motor to reverse direction. Additional control is available via Cresnet. Four pushbuttons on the face of the unit allow the motors to be activated without Cresnet control, which is particularly useful when operating the unit locally during installation. Specifications The following table summarizes the specifications for the C2N-SDC-DC.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller occurs when the motors are initially activated. A dedicated power supply for the C2N-SDC-DC and associated motors is recommended. 2. The latest versions can be obtained from the Crestron website. Refer to NOTE after last footnote. 3. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product Catalog for a complete list of 2-Series control systems. 4. Filenames for CNX update files have a UPZ extension.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC C2N-SDC-DC, Physical Views, Front and Side C2N-SDC-DC, Physical Views, Rear 4 y Shade & Drape DC Motor Controller: C2N-SDC-DC Operations & Installation Guide - DOC.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Controls and Indicators Industry Compliance As of the date of manufacture, the C2N-SDC-DC has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Setup Network Wiring CAUTION: In order to ensure optimum performance over the full range of your installation topology, Crestron Certified Wire, and only Crestron Certified Wire, should be used. Failure to do so may incur additional charges if support is required to identify performance deficiencies as a result of using improper wire. CAUTION: Use only Crestron power supplies for Crestron equipment.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. Refer to the following table. Wire Gauge Values RESISTANCE WIRE GAUGE (R or Ohms) (AWG) (MM2) 4 6 10 15 13 8.7 16 18 20 22 1.50 0.75 0.50 0.34 Doubled CAT5 Tripled CAT5 NOTE: All Cresnet wiring must consist of two twisted pairs.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Identity Code Every piece of equipment and user interface within the network requires a unique identity code (Net ID or Cresnet ID). These codes are two-digit hexadecimal numbers from 03 to FE (ID 02 is reserved for control systems). The Net ID of each unit must match an ID code specified in the SIMPL Windows program. The Net ID of the C2N-SDC-DC has been factory set to 23. The Net IDs of multiple C2N-SDC-DCs in the same system must be unique.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller 3. Right-click the C2N-SDC-DC Net ID and open the sub-menu. This menu provides a wide range of functions, including; change the Net ID, open text console, upload project, update firmware, etc. Network Device Tree Sub-Menu 4. Select “Change Network ID…”. A box appears around the Net ID, allowing you to make the change. Toolbox will not allow a duplicate ID number. Network Device Tree – Change Net ID Operations & Installation Guide - DOC.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Hardware Hookup Refer to the following hookup diagram. The C2N-SDC-DC is equipped with three connector plugs that have screw terminals. Use these connectors to attach the motor wires and Cresnet wires to the C2N-SDC-DC. NOTE: All wiring must be installed in accordance with all local and national electrical codes. NOTE: Three Watts are consumed by the C2N-SDC-DC when the motors are not operating.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller NOTE: The UP ▲button applies +24 VDC to pin A (referenced to pin B). The DOWN ▼ button applies +24 VDC to pin B (referenced to pin A). If the shade does not go in the desired direction when the button is pressed, reverse the polarity of the shade motor wires. Installation The C2N-SDC-DC may be mounted in a two-gang electrical box or a 4 x 4 inch (1900) electrical box. Ensure that you are using a box with sufficient depth (minimum 1.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Installation in a Two-Gang Electrical Box 4 x 4 Inch Box Mounting When mounting the C2N-SDC-DC in a 4 x 4 inch electrical box, use the two 8-32 x 3/8 inch pan head screws as shown in the following illustration. Installation in a 4 x 4 Inch (1900) Electrical Box 12 y Shade & Drape DC Motor Controller: C2N-SDC-DC Operations & Installation Guide - DOC.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Programming Software NOTE: Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Earliest Version Software Requirements for the PC NOTE: Crestron recommends that you use the latest software and that each device contains the latest firmware to take advantage of the most recently released features. Please check the Crestron website (http://www.crestron.com/updates) for the latest versions of software and firmware. New users are required to register to obtain access to this site.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller SIMPL Windows is Crestron’s software for programming Crestron control systems. It provides a well-designed graphical environment with a number of workspaces (i.e., windows) in which a programmer can select, configure, program, test, and monitor a Crestron control system. SIMPL Windows offers drag and drop functionality in a familiar Windows® environment. This section describes a sample SIMPL Windows program that includes a C2N-SDC-DC.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC C2Net-Device Slot in Configuration Manager To incorporate a C2N-SDC-DC into the system, drag the C2N-SDC-DC from the Cresnet Control Modules | Cresnet Shade Drape Controllers folder of the Device Library and drop it in System Views. The PRO2 system tree displays the C2N-SDC-DC in Slot 9, with a default Net ID of 23 as shown in the following illustration.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller “Device Settings” Window NOTE: SIMPL Windows automatically changes the Net ID value of a device added to a program if a device with the same Net ID already exists in the program. Always ensure that the hardware and software settings of the Net ID match. For Net ID hardware setting details, refer to “Identity Code” on page 8.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Uploading and Upgrading NOTE: Crestron recommends that you use the latest software and that each device contains the latest firmware to take advantage of the most recently released features. Please check the Crestron website (http://www.crestron.com/updates) for the latest versions of software and firmware. New users are required to register to obtain access to this site.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller system. These documents are available from the Crestron website. Refer to the following figure for a typical connection diagram when uploading files. NOTE: Use a standard DB9 male to female “straight-through” cable for 2-Series controllers. Typical Connection Diagram when Uploading 1. Ensure that all devices are connected to the control processor and the control processor is connected via serial cable to the PC. 2. Open Crestron Toolbox. 3.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC The PC communication settings specified here should match the protocol that the control processor expects. The usual settings are as follows. • Port = COM 1 through COM 8. Select the correct COM port on the PC. • Baud rate = Auto-Detect (or 115200). • Parity = None. • Number of data bits = 8. • Number of stop bits = 1. • Hardware handshaking (RTS/CTS) enabled. • Software handshaking (XON/XOFF) not enabled. “Address Book” Window – Serial Setup 4.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Communications are confirmed when the network devices are displayed. To view a specific device, expand the network device tree by clicking +. Expand the network device tree until the device to be managed is selected. Right-click the desired Net ID to open the sub-menu. This menu provides a wide range of functions, including; change the Net ID, open text console, upload project, update firmware, etc.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Uploading a SIMPL Windows Program The SIMPL Windows file can be uploaded to the control system using SIMPL Windows or via the Crestron Toolbox. Upload via SIMPL Windows 1. Start SIMPL Windows. 2. Select File | Open to view the “Open” window, navigate to the SIMPL Window file (.smw), and click Open. 3. Select Project | Transfer Program. NOTE: A control system source file has the extension .smw. A compiled SIMPL Windows file has the extension .
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller 4. When the “System Info” window appears, the Functions option becomes available from the menu bar. 5. Select Functions | SIMPL Program. The “SIMPL Program” window contains information about the currently loaded SIMPL program (if any), and permits you to stop, start, erase, retrieve, and upload a SIMPL program. This menu also permits you to upload to compact flash or internal flash. “SIMPL Program” Window 6. Click the program.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC “Open” Window 7. Select a file and click Open. When the “SIMPL Program” window re-opens click Send. Firmware Upgrade To take advantage of all the C2N-SDC-DC features, it is important that the unit contains the latest firmware available. Please check the Crestron website for the latest version of firmware.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller “Network Device Tree” Window – Right-Click Sub Menu 5. The “Firmware” window displays the model and current firmware version. Click Upload New Firmware to browse for the firmware file. “Firmware” Window 6. When the following screen appears, browse to locate the firmware (.csf) file. Operations & Installation Guide - DOC.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Locate Firmware in the “Open” Window 7. Click Open and the file transfers to the unit. 8. The “Firmware” window indicates the new firmware version. Click Close. The device reboots with the new firmware. Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller C2N-SDC-DC Troubleshooting (continued) TROUBLE Yellow NET LED does not illuminate Shade/Drape move in opposite direction desired Shade/Drape does not respond SETUP LED is on steady SETUP LED is flashing PROBABLE CAUSE(S) CORRECTIVE ACTION Improper Net ID Verify that the C2N-SDC-DC Net ID matches the Net ID in the software program Loose network Verify that cable plugged into NET port is secure connection Incorrect Reverse the polarity of shade/dra
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www.crestron.com) for a listing of Crestron worldwide offices.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Shade & Drape DC Motor Controller Crestron C2N-SDC-DC This page intentionally left blank. 30 y Shade & Drape DC Motor Controller: C2N-SDC-DC Operations & Installation Guide - DOC.
Crestron C2N-SDC-DC Shade & Drape DC Motor Controller This page intentionally left blank. Operations & Installation Guide - DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 6373 (2012949) 07.05 Specifications subject to change without notice.
