Crestron C2N/C2NI-CB Series ® Cameo Keypads Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON The specific patents that cover Crestron products are listed at patents.crestron.com. Crestron, the Crestron logo, Cameo, Cresnet, Crestron Toolbox, D3 Pro, SIMPL+, SystemBuilder, and VT Pro-e are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
Crestron C2N/C2NI-CB Series Cameo Keypads Contents Cameo Keypads: C2N/C2NI-CB Series 1 Introduction ...................................................................................... 1 Features and Functions .......................................................... 1 Specifications ......................................................................... 3 Physical Description .............................................................. 4 Industry Compliance.......................................
Crestron C2N/C2NI-CB Series Cameo Keypads Cameo Keypads: C2N/C2NI-CB Series Introduction Features and Functions • Stylish and versatile wall mount keypads (standard mount, flush mount, or UK mount) • Versatile combination of engravable buttons • "Rocker" action supports up to three functions per button • Installer-configurable with an assortment of three button sizes and blank spacers • Tapered buttons for enhanced tactile response • Elegant white LED light pipe feedback • Cresnet® communications • Quick
Cameo Keypads Crestron C2N/C2NI-CB Series Cameo Standard Mount The Cameo standard mount model, C2N-CBD, is designed for installation in a conventional electrical gang-box using a decorator style faceplate (not included). Cameo Flush Mount Cameo's unique flush mount design affords a very discreet appearance occupying just one-third the space of a conventional keypad. Employing a smart spring clamp mounting system, the C2N-CBF Cameo flush mount model installs easily in drywall without requiring a back box.
Crestron C2N/C2NI-CB Series Cameo Keypads dimly for enhanced visibility in a darkened room. Adjustable button backlighting is also provided. Specifications Specifications for the C2N/C2NI-CB Series keypads are listed in the following table.
Cameo Keypads Crestron C2N/C2NI-CB Series 2. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product Catalog for a complete list of 2-Series control systems. 3. Minimum Non 2-Series Control System Update Files: CEN/CN/TVAV Version 5.12.63V.UPZ or later CNMSX-AV/PRO Version 5.14.02X.UPZ or later CNRACKX/-DP Version 5.14.02W.UPZ or later ST-CP Version 4.02.4S.UPZ or later CNX update files are required for either CNMSX-AV/PRO or CNRACKX/-DP.
Crestron C2N/C2NI-CB Series Cameo Keypads Keypad Overall Dimensions – Flush Mount Configuration 1.73 in (4.38 cm) 1.52 in (3.86 cm) 3.20 in (8.13 cm) Operations & Installation Guide - DOC.
Cameo Keypads Crestron C2N/C2NI-CB Series Keypad Overall Dimensions – Standard Mount Configuration 1.52 in (3.86 cm) 1.80 in (4.56 cm) 4.12 in (10.47 cm) 6 • Cameo Keypads: C2N/C2NI-CB Series Operations & Installation Guide - DOC.
Crestron C2N/C2NI-CB Series Cameo Keypads Keypad Overall Dimensions – UK Mount Configuration 1.14 in (2.89 cm) 1.52 in (3.86 cm) 0.30 in (0.76 cm) 3.38 in (8.58 cm) 3.38 in (8.58 cm) Operations & Installation Guide - DOC.
Crestron C2N/C2NI-CB Series Cameo Keypads Rear Housing and Switch Assembly Front Rear 2 1 Bottom Connectors, Controls & Indicators # 1 CONNECTORS*, CONTROLS & INDICATORS LED Light Pipes 2 DESCRIPTION Six pinhead-sized white LED light pipes provide button feedback and bargraph capability Four-position terminal block connector for data and power. Connects to Cresnet control network.
Crestron C2N/C2NI-CB Series Cameo Keypads Industry Compliance As of the date of manufacture, the C2N/C2NI-CB Series keypads have been tested and found to comply with specifications for CE marking. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cameo Keypads Crestron C2N/C2NI-CB Series Setup Network Wiring When wiring the network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (http://www.crestron.com/calculators).
Crestron C2N/C2NI-CB Series Cameo Keypads The button caps are tapered, and are often installed in a shingle-style pattern (refer to the “C2N/C2NI-CB Series Keypad Physical Views” illustration on page 4). Usual orientation of the keypad is with the LEDs on the left. It can, however, be inverted with the LEDs on the right, but the original relationship of the button numbers to the LEDs remains, i.e.
Crestron C2N/C2NI-CB Series Cameo Keypads Supplied Parts/Assemblies – Flush Mounting (Continued) QTY 2 ITEM 1 Single row spacer Double row spacer Triple row spacer Plastic button support Spring clamp 1 Template 1 1 1 DESCRIPTION Switch cover for single non-operational switch Switch cover for two non-operational switches Switch cover for three non-operational switches Used to hold the button caps/spacers together in position Used to secure the assembled keypad in the wall Used to mark correct hole
Crestron C2N/C2NI-CB Series LED Holes Cameo Keypads Bezel Button Caps and Spacers LED Light Pipes Cover Screw Plastic Button Support Rear Housing and Switch Assembly 5. Attach the spring clamp to the rear of the keypad, as shown in the following figure, by loosening the screws sufficiently to place the clamp over the screws and slide it down into position, and then retighten the screws. Loosen Screws Spring Clamp Operations & Installation Guide - DOC.
Cameo Keypads Crestron C2N/C2NI-CB Series 6. Use the supplied template to prepare the hole in the wall. (Refer to the Appendix on page 34 for an illustration of the template.) NOTE: Be very careful when cutting the hole. There are no adjustments for alignment with the spring clamp. After the Cresnet network wiring has been installed and verified, use the following procedure to install the keypad in the prepared hole. 1. Turn Cresnet system power OFF. 2.
Crestron C2N/C2NI-CB Series Cameo Keypads careful to avoid damage to the wall surface, and use your fingers to remove the keypad. Standard Mounting Installation The keypad for standard mounting installation is supplied partially assembled along with several items as listed in the following table.
Crestron C2N/C2NI-CB Series Cameo Keypads Assemble the keypad as described in the following steps. Refer to the accompanying illustrations. 1. Arrange the button caps and/or spacers in position according to the program plan. Attach the plastic button support to the button caps/spacers, and put the assembled parts in place on the rear housing and switch assembly. 2.
Crestron C2N/C2NI-CB Series Cameo Keypads After the Cresnet network wiring has been installed and verified, use the following procedure to install the keypad in a standard, single-gang electrical box (not supplied). 1. Turn Cresnet system power OFF. 2. Connect the Cresnet cable to the keypad’s Cresnet port, using the supplied mating connector. CAUTION: Excess wire pinched between the keypad and electrical box could short out.
Crestron C2N/C2NI-CB Series Cameo Keypads 5. Attach the desired decorator style faceplate (not supplied). 6. Turn the Cresnet system power ON. UK Mounting Installation The keypad for UK mounting installation is supplied partially assembled along with several items as listed in the following table.
Crestron C2N/C2NI-CB Series Cameo Keypads 3. Hold the bezel and rear housing together and install and tighten the two supplied Phillips pan head, 4-40 x 3/16” cover screws (black), as shown in the illustration. Bezel LED Holes Button Caps and Spacers LED Light Pipes Cover Screw Plastic Button Suport Rear Housing and Switch Assembly 4. Press each button to be certain that you feel the press and release to ensure that the button caps move freely.
Cameo Keypads Crestron C2N/C2NI-CB Series 3. Insert the keypad into the hole and press the bezel against the plastic wall plate until it snaps securely into position. 4. Turn the Cresnet system power ON. If the keypad needs to be removed from the wall, there are two slots on one edge of the bezel (visible on the bottom edge of view C in the figure on page 21). Use a flat blade screwdriver to pry the bezel away from the wall plate, being careful to avoid damage to the bezel.
Crestron C2N/C2NI-CB Series Cameo Keypads Mounting Using Screws Through the Bezel Refer to the figure on the next page and do the following. 1. Drill pilot holes through the bezel from the rear at each of the drill center points. Then, from the front of the bezel, drill the final holes and countersink as required. (Refer to C in the following figure.) 2. Place the plastic wall plate over the keypad with the smooth surface facing out, and snap the wall plate and bezel together. 3.
Crestron C2N/C2NI-CB Series Cameo Keypads Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account.
Crestron C2N/C2NI-CB Series Cameo Keypads Software (Continued) TASK Program with simple wizards for systems using a C2N/C2NI-CB Series keypads. Software for lighting and environmental controls (optional) Create labels for front panel buttons. REQUIRED SOFTWARE VERSION Crestron SystemBuilder™ version 1.0 or later (requires SIMPL Windows, VT Pro-e®, Crestron Database and Crestron Engraver) with SystemBuilder Templates version 1.0 or later.
Cameo Keypads Crestron C2N/C2NI-CB Series selecting it from one of the toolboxes and dragging it to a room. The available toolboxes differ depending on the View but all Views include a "General" toolbox that allows you to add areas and rooms at any time. Programming with SIMPL Windows NOTE: While SIMPL Windows can be used to program the C2N/C2NI-CB Series keypads, it is recommended to use SystemBuilder for configuring a system.
Crestron C2N/C2NI-CB Series Cameo Keypads C2Net Device, Slot 9 • Additional C2N/C2NI-CB Series devices are assigned different Net ID numbers as they are added. • If necessary, double click a device to open the “Device Settings” window and change the Net ID, as shown in the following figure. “C2N-CB Device Settings” Window • The ID code(s) specified in the SIMPL Windows program must match the Net ID of each unit. Operations & Installation Guide - DOC.
Crestron C2N/C2NI-CB Series Cameo Keypads Program Manager Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols. The symbol can be viewed by double-clicking on the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1).
Crestron C2N/C2NI-CB Series Cameo Keypads NOTE: A Crestron module in Crestron Database version 17.1.0, the C2N-Cameo Bargraph Feedback v1.0, makes it possible to use the feedback LEDs like a bargraph, so that for a function like volume control, as the switches are used to control the volume, the LEDs display its approximate level. Operations & Installation Guide - DOC.
Crestron C2N/C2NI-CB Series Cameo Keypads Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device).
Crestron C2N/C2NI-CB Series Cameo Keypads SIMPL Windows If a SIMPL Windows program is provided, it can be uploaded to the control system using SIMPL Windows or Crestron Toolbox. Firmware Check the Crestron website to find the latest firmware. (New users may be required to register to obtain access to certain areas of the site, including the FTP site.) • Upgrade C2N/C2NI-CB firmware via Crestron Toolbox.
Crestron C2N/C2NI-CB Series Cameo Keypads Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. C2N/C2NI-CB Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION The keypad does not function. The wrong power supply is being used. The unit is not receiving power, or is receiving insufficient power. Use a Crestron power supply.
Crestron C2N/C2NI-CB Series Cameo Keypads Check Network Wiring Use the Right Wire In order to ensure optimum performance over the full range of your installation topology, Crestron Certified Wire and only Crestron Certified Wire may be used. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire. Calculate Power CAUTION: Use only Crestron power supplies for Crestron equipment.
Crestron C2N/C2NI-CB Series Cameo Keypads NOTE: All Crestron certified Cresnet wiring must consist of two twisted pairs. One twisted pair is the +24V conductor and the GND conductor and the other twisted pair is the Y conductor and the Z conductor. Strip and Tin Wire When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Twist together the ends of the wires that share a pin on the network connector and tin the twisted connection.
Crestron C2N/C2NI-CB Series Cameo Keypads You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. Future Updates As Crestron improves functions, adds new features and extends the capabilities of the C2N/C2NI-CB, additional information may be made available as manual updates.
Crestron C2N/C2NI-CB Series Cameo Keypads Appendix: Template for Flush Mount Hole The following figure (not to scale) illustrates the supplied template used to prepare the hole in the wall or other mounting surface for the flush mount Cameo keypad. NOTE: Use only the original template, not a photocopy, to prepare the hole. Photocopies usually alter the size of the image slightly, which would make the hole the wrong size.
Crestron C2N/C2NI-CB Series Cameo Keypads Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide - DOC. 6560B (2017268) 03.14 Specifications subject to change without notice.