Specifications

ManualsBrandsCrestron ManualsHome building and DecorCLSI-C6M

iLux Lighting Systems

Crestron Electronics, Inc. Installation Guide – DOC. 6413E

15 Volvo Drive Rockleigh, NJ 07647 (2014211)

Tel: 888.CRESTRON 04.13

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Introduction

Features and Functions

The iLux

units, CLSI-C6 and CLSI-C6M, are complete wall-mounted integrated lighting systems that can function

as standalone devices or be part of a Crestron

solution total control system network (Cresnet

). The units are

functionally identical except that the CLSI-C6M includes a built-in motion sensor.

CLSI-C6M with Cover Open (Shown in Almond)

Specifications

Following are specifications for the iLux units.

CLSI-C6 & CLSI-C6M Specifications

SPECIFICATIONS DETAILS

Power Requirements Line power, 230 Vac, 50/60 Hz

Load Ratings

Max load per channel

Min load per channel

Max load per unit

800 W/VA (3.5 amps @ 230 Vac), expandable via CLS-EXP expansion

modules (sold separately)

25 W/VA (0.108 amps @ 230 Vac)

2300 W/VA (10 amps @ 230 Vac)

Load Types LED

, incandescent, magnetic low-voltage, neon/cold cathode, 2-wire

dimmable fluorescent, and non-dim lighting;

Electronic low-voltage, 3 and 4-wire fluorescent, high-inrush switching,

and 277 V via CLS-EXP Series expansion modules

Cresnet Power Available

for Local Devices

10 W maximum

External power supplies sold separately

IR Receiver

Reception Frequency 36 kHz, For use with Crestron IR remote CLS-IRHT8

Motion Detector

(CLSI-C6M only)

Type

Range

Infrared

6 to 9 meters at 1.2 meter elevation

(20 to 30 feet at 4-foot elevation)

(Continued on following page)

Summary of content (14 pages)

PAGE 1
iLux Lighting Systems Introduction Features and Functions The iLux® units, CLSI-C6 and CLSI-C6M, are complete wall-mounted integrated lighting systems that can function as standalone devices or be part of a Crestron® solution total control system network (Cresnet®). The units are functionally identical except that the CLSI-C6M includes a built-in motion sensor. CLSI-C6M with Cover Open (Shown in Almond) Specifications Following are specifications for the iLux units.
PAGE 2
iLux Lighting Systems CLSI-C6 & CLSI-C6M Specifications (Continued) SPECIFICATIONS DETAILS Default Net ID 1F Environmental Temperature 0° to 40° C (32° to 104° F) Humidity Overall Dimensions: Height Width Depth Weight 10% to 90% RH (non-condensing) 114 mm (4.48 in) 226 mm (8.89 in) 63 mm (2.47 in) for CLSI-C6 66 mm (2.60 in) for CLSI-C6M 649 g (23 oz) 1. If the unit is fed from an arc fault circuit interrupter, the maximum total load is 1000 W/VA to avoid nuisance tripping. 2.
PAGE 3
iLux Lighting Systems Installation Important Notes (Read Before Installation) • Codes: Install in accordance with all local and national electrical codes. • Wiring: Use copper wire only. For supply connections, use wires rated for at least 75°C. • Lighting Load Types: LED, incandescent, magnetic low-voltage, neon/cold cathode, 2-wire dimmable fluorescent, and non-dim lighting.
PAGE 4
iLux Lighting Systems 1. Feed the wires (power line from the distribution panel, load wires, plus any required Cresnet cables) through the holes in the electrical box. Then install the box in the wall. 2. Hold the rear of the CLSI-C6M unit and remove the front panel and cover assembly by carefully pulling out and up from the bottom edge. CLSI-C6M Installation 4-Gang Electrical Box Mounting Screws (4) Control Panel Overlay Front Cover Assembly 3.
PAGE 5
iLux Lighting Systems Adding External Power Supplies Additional power supplies are required to support more than four keypads or shade controllers on the LOCAL DEVICES network. Also, each shade controller requires its own additional power supply. The illustration below shows a scenario where an external power supply is required to add a shade controller and other devices to a network that already contains four shade controllers.
PAGE 6
iLux Lighting Systems Wiring Occupancy Sensors and Photocells NOTE: Ensure that all CLSI-C6 and CLSI-C6M devices contain the latest firmware to take advantage of the most recently released features.
PAGE 7
iLux Lighting Systems Setup Network Wiring When wiring the network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (http://www.crestron.com/calculators).
PAGE 8
iLux Lighting Systems CLSI-C6 Installation Configurations (Continued) Method 3: Same as Method 1 plus a 2-Series control system communicating with the CLSI. 2-Series Control System Cresnet Cresnet (Control System) Other Cresnet Devices Why? Control system can control and monitor operation of the lighting system. Can trigger lighting scenes from touch screens, RF wireless remotes, computers, or real-time clock. Buttons on lighting system can control other functions.
PAGE 9
iLux Lighting Systems Supported Devices The following table lists devices supported by the iLux units and their power requirements. Supported Devices Power Requirements NAME DESCRIPTION CRESNET POWER FACTOR (W) MAX QTY C2N-DB6 6-Button Keypad 3 watts 16 C2N-DB8 8-Button Keypad 3 watts 16 C2N-DB12 12-Button Keypad 3 watts 16 C2N-CBD/CBF (All Models) Cameo Keypad ® 0.5 watts 16 C2NI-CB/ INETI-CB Cameo Keypad (International) 0.
PAGE 10
iLux Lighting Systems Testing The following illustration shows the front panel of the unit and the controls used during installation. Front Panel Controls and Indicators LED Bar Graphs 1 2 3 4 Two-Digit Lights Display Button 5 6 M in S ec ^ ^ S cene 1 S cene 2 S cene 3 S cene 4 S cene 5 Ligh ts S hade s S ave C an cel S cene 6 ^ ON ^ OFF Function Buttons Verify the basic installation and wiring connections as follows: 1.
PAGE 11
iLux Lighting Systems Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. CLSI-C6/C6M Installation Troubleshooting TROUBLE Unit does not function. POSSIBLE CAUSE(S) CORRECTIVE ACTION Unit is not receiving line power. Verify that the unit is properly connected to the power line and that the circuit breaker is closed. Loads are not connected.
PAGE 12
iLux Lighting Systems Strip and Tin Wire When daisy chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Twist together the ends of the wires that share a pin on the network connector and tin the twisted connection. Apply solder only to the ends of the twisted wires. Avoid tinning too far up the wires or the end becomes brittle. Insert the tinned connection into the Cresnet connector and tighten the retaining screw.
PAGE 13
iLux Lighting Systems Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PAGE 14
iLux Lighting Systems This page is intentionally left blank. 14 • iLux Lighting Systems: CLSI-C6 & CLSI-C6M Installation Guide – DOC.