Crestron CLW-DIM1/4RF, CLW-DIMS1/4RF, CLW-SLVD1RF infiNET™ Dimmers Operations Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2007 Crestron Electronics, Inc.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Contents infiNET™ Dimmers: CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Specifications .......................................................................................................
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers infiNET™ Dimmers: CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Introduction Features and Functions The CLW-DIM1RF (-DIM1RF) one-button dimmer and CLW-DIM4RF (-DIM4RF) four-button dimmer are stand-alone wall box dimmers that can also act as wireless infiNET™ devices that report to a Crestron® control processor via a Crestron infiNET wireless gateway. infiNET Dimmers Functional Summary • • • • Two-way infiNET dimmers ⇒ 2.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF C2N-MNETRPT infiNET Repeaters) can communicate with one C2N-MNETGW infiNET Gateway and, if more devices are needed, more C2N-MNETGW gateways may be added to a Cresnet® network. Crestron infiNET dimmers operate on the 2.4 GHz “ISM band” (2400 MHz to 2483.6 MHz) at 10 mW.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Specifications Following are specifications for the -DIM1RF, -DIM4RF, -DIMS1RF, -DIMS4RF, and -SLVD1RF. CLW-DIM1/4RF, CLW-DIMS1/4RF, & CLW-SLVD1RF Specifications SPECIFICATION Power Requirements Line Power, 120 VAC, 60 Hz Operating Frequency 2400 MHz to 2483.6 MHz (802.15.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF NOTE: Crestron software and any files on the website are for Authorized Crestron dealers and Crestron Authorized Independent Programmers (CAIP) only. New users may be required to register to obtain access to certain areas of the site (including the FTP site).
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Parts of CLW-DIM4RF, -DIMS4RF Button 1 Button 2 Button 3 Button 4 RUN SET OFF Mode Selection Switch Physical View of CLW-DIM4RF/-DIMS4RF (Clockwise from Top; Top, Side, and Front) 1.75 in (4.45 cm) 2.38 in (6.03 cm) 1.88 in (4.77 cm) 3.81 in (9.68 cm) 3.28 in (8.32 cm) RUN SET 2.70 in (6.86 cm) 4.13 in (10.48 cm) OFF 1.50 in (3.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Physical View of CLW-SLVD1RF (Clockwise from Top; Top, Side, and Front) 1.88 in (4.77 cm) 1.75 in (4.45 cm) 3.81 in (9.68 cm) 3.28 in (8.32 cm) 2.70 in (6.86 cm) 4.13 in (10.48 cm) 1.50 in (3.81 cm) The -DIM1RF, -DIM4RF, -DIMS1RF, -DIMS4RF, and -SLVD1RF mount in a standard wallbox and are covered using a decorative faceplate (not included). All line voltage connections are made at the rear of the dimmer.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Industry Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. E239011 FCC ID: EROCWD1011 Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Acquire the Dimmer on the infiNET Network Before an infiNET device can be used on an infiNET network, it must first be acquired to a C2N-MNETGW gateway that is connected to a Cresnet network. NOTE: The -DIM1RF, -DIM4RF, -DIMS1RF, and -DIMS4RF can also work as stand-alone wall box dimmers without being acquired by a C2N-MNETGW. NOTE: A dimmer can be acquired to only one gateway.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF 3. infiNET™ Dimmers Take the C2N-MNETGW out of the Acquire mode once all devices have been acquired. Refer to the latest revision of the C2N-MNETGW Operations Guide (Doc. 6317), which is available from the Crestron website. To communicate with the control system program, an MNET ID value between 03 and 20 must be assigned to the dimmer. For information on assigning MNET ID values, refer to “Identity Code” on page 13.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Operation NOTE: The device may be warm to the touch during operation. This is normal. Mode Selection Switch These dimmers use a three-position mode selection switch to set the mode of operation. • OFF When the mode selection switch is in the “OFF” position, the pushbutton(s) will not have any function and the load is disconnected from the power source.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers 3. The dimmer will not “bounce” at the limit and dim in the opposite direction. If the button is pressed and held again, the dimmer will dim in the opposite direction. If other events have occurred since the last “cycle-dim” operation, the dimmer will dim up if the light level was < 50%. If the light level was ≥ 50%, the dimmer will dim down. • SET When the mode selection switch is in the “SET” position, it is operating in the SET mode.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF After setting the preset value(s), return the mode selection switch to the “RUN” position. -SLVD1RF The -SLVD1RF has one rocker button. The -SLVD1RF does not have a mode selection switch. It will emulate the RUN mode of the -DIMS1RF (even if connected to a -DIMS4RF) unless the mode selection switch of the master is set to “OFF”.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Identity Code Just like every device on a Cresnet system requires a unique identity code (NET ID), every device and user interface on the infiNET network requires a unique identity code (MNET ID). These codes are two-digit hexadecimal numbers from 03 to 20. The MNET ID of each unit must match an ID code specified in the SIMPL Windows program. Refer to “Programming with SIMPL Windows” on page 23 for details of the SIMPL Windows procedure.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF The infiNET switch and dimmers have already been acquired as described in the acquiring procedure described on page 8. The devices have been assigned the default MNET ID 01 as shown in the Network Device Tree window below. Network Device Tree 1. With the Network Device Tree open, select Tools | SMW Program Tree, or click . SMW Program Tree-Click to Select Program 2.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers SMW Program Tree Devices with NET IDs or MNET IDs that have been identified by the SMW icon. Devices with NET IDs or MNET Program Tree are marked with a IDs that could not be identified are marked with a icon. NOTE: Descriptions such as “BR Dimmer”, “LR Dimmer”, and “kitchen switch” were created by editing each devices symbol name in the SIMPL Windows Programming Manager.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF 4. In the SMW Program Tree, right-click on the top level of the tree and select Link with Network Control. Link with Network Control A window will be displayed with instructions for linking the SMW Program Tree to the Network Device Tree. Link Instruction Window ). 5. Click OK. The cursor will change to a target selector ( 6.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Setup Lighting Window The listed devices can be sorted in ascending or descending order by clicking on the column headers. The order can also be adjusted by selecting a device and clicking the or buttons. This can be used when setting up devices in the order they will be encountered.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF The LEDs on all of the CLW-DIM1RF dimmers on the list will flash. 9. Physically locate the dimmer in the bedroom with the flashing LED and touch the top or bottom of the large button. The status of the “BR dimmer” will change from “Not Verified” to “Setup Complete” and the next device on the list (CLW-DIM1RF, MNET ID 03, “LR dimmer”) will be highlighted. Touching a device may result in setting a duplicate MNET ID. A warning will be displayed.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Setup Complete 11. Click Close to close the window once all devices have been identified. All of the identified devices in the Network Device tree will be indicated with icon as shown in the following diagram.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF “Network Device Tree” with Newly Added infiNET Device 3. Expand the device tree until the MNET ID that is to be changed is visible. Right-click on the MNET ID, and when the sub-menu appears, select Change Network ID. “Network Device Tree” - Sub-Menu NOTE: Any infiNET dimmer in the Network Device Tree can be identified using Crestron Toolbox. Right-click a device in the Network Device Tree and select “Identify this…”.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Repeat this procedure for each additional infiNET device requiring a MNET ID change. WARNING: Devices with an MNET ID of 01 or 02 cannot be used in a control system program. These devices will be indicated with a icon. Operations Guide - DOC.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Programming with D3 Pro Crestron’s D3 Pro lighting software provides all the tools necessary to create a complete Crestron lighting system for residential applications. The lighting system includes the control system logic program, touchpanel projects and keypad programming, documentation and real-time lighting adjustment capabilities.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Adding an infiNET Device to the C2N-MNETGW • The system tree of the control system displays the device in the appropriate slotwith a default MNETID as shown in the following illustration. C2Net Device, Slot 6, with infiNET Device SIMPL Windows adds the selected infiNET device with a default MNET ID.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF • infiNET™ Dimmers If necessary, double click a device to open the “Device Settings” window and change the MNET ID, as shown in the following figure. “Device Settings” Window for the CLW-DIM1RF • Program Manager The MNET ID specified in the SIMPL Windows program must match the MNET ID of each unit. Refer to “Identity Code” on page 13. Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device).
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Firmware infiNET™ Dimmers Check the Crestron website to find the latest firmware. (New users may be required to register to obtain access to certain areas of the site, including the FTP site.) Upgrade the infiNET device’s firmware via Crestron Toolbox. • Establish communication with the infiNET device and display the “System Info” window. • Select Functions | Firmware… to upgrade the infiNET device’s firmware.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Problem Solving Troubleshooting The table after this paragraph provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. infiNET Dimmer Troubleshooting TROUBLE Dimmer does not function. Dimmer does not respond to control system commands. POSSIBLE CAUSE(S) CORRECTIVE ACTION Dimmer is not receiving line power.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers infiNET Dimmer Troubleshooting (continued) Operations Guide - DOC. 6396A TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Dimmer presses are not reported to control system. If the LED flashes OFF for ¼ second two times, then returns to low, the MNET ID of device is not set to match the MNET ID of the SIMPL Windows program. Using Crestron Toolbox, poll the network.
infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Bootloader In rare cases, it may be necessary to bypass the dimmer’s standard firmware and enter into the “bootloader”. This might be necessary if the unit was loaded with a faulty version of firmware that might prevent future firmware upgrades. To enter the bootloader, set the mode selection switch to “OFF”. Press and hold the up button (or Button 1 on the -DIM4RF or -DIMS4RF) while setting the mode selection switch to “RUN”.
Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF infiNET™ Dimmers Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide - DOC. 6396A (2014133) 10.07 Specifications subject to change without notice.
