Specifications

7 Channel Surround-Sound Amplifier Crestron CNAMPX-7X200
The CNAMPX-7X200 is also available in an international version. All of the features
are identical with the exceptions of the international AC power requirements, the
power rating of the Master Switch circuit breaker, the power cord and the unit
nomenclature of CNAMPXI-7X200. Throughout this operations guide, all references
to CNAMPX-7X200 apply to both versions except where noted.
Specifications
The following table provides specifications for the CNAMPX-7X200 and
CNAMPXI-7X200.
CNAMPX-7X200 Specifications
SPECIFICATION DETAILS
Power Input Requirements: US version
International version
120 VAC ±10%, 60 Hz, 2400 Watts, 20 Amps max.
230 VAC ±10%, 50 Hz, 2400 Watts, 10 Amps max.
Cresnet Power Requirements 3 Watts (24VDC @ 0.125A)
Default NET ID 3F
Channels 7
Output Power – All channels driven, 20Hz
to 20KHz, at rated THD
200 Watts/Channel into 8-ohm loads
300 Watts/Channel into 4-ohm loads
Input Impedance 28K ohms
Power Bandwidth – 3dB 3Hz to 150KHz
Frequency Response @ 1W 8ohm Flat +0, -0.1dB from 20Hz to 20Khz
Total Harmonic Distortion @ full power 0.02% or less
SMPTE I.M. Distortion @ full power 0.05% or less
Signal to Noise Ratio (S/N) “A” Weighted > 110dB
Gain 28dB
Damping Factor > 1000
Channel Separation over full bandwidth > 100dB
Environmental Temperature &
Humidity
41 to 104° F (5 to 40°C)
10 to 90% RH (non-condensing)
Rack Space Required 4U (not including free rack space above and
below)
Master Switch 20-Amp Magnetic Circuit Breaker (US version)
10-Amp Magnetic Circuit Breaker (Int’l version)
Control System Update Files
1, 2, 3
2-Series Control System Update
CEN/CN-TVAV Update File
CNMSX-AV/Pro Update File
CNRACKX/-DP Update File
ST-CP Update File
Version C2-1001.CUZ or later
Version 5.10.13V.UPZ or later
Version 5.10.11X.UPZ or later
Version 5.10.11W.UPZ or later
Version 4.01.04S.UPZ or later
Dimensions & Weight Height: 7.70 in (19.56 cm)
Width: 19.0 in (48.26 cm) – with ears
17.18 in (43.64 cm) – without ears
Depth: 18.88 in (47.95 cm)
Weight: 94.4 lb (42.48 kg)
1. The latest versions can be obtained from the Downloads | Software Updates page of the Crestron
website (www.crestron.com)
. Refer to NOTE after last footnote.
2. Crestron 2-Series control systems include the AV2 with CAGE2, PAC2, PRO2, and RACK2.
3. CNX update files are required for either CNMSX-AV/Pro or CNRACKX/-DP. Filenames for CNX
update files have a UPZ extension and ST-CP files are in one EXE or zipped UPZ file. To avoid
program problems, make certain you are using the update file with the correct suffix letter (e.g., S, V,
W, X).
NOTE: Crestron software and any files on the FTP site are for Authorized Crestron
dealers only. New users may be required to register to obtain access to certain areas
of the FTP site.
2 7 Channel Surround-Sound Amplifier: CNAMPX-7X200 Operations Guide – DOC. 8179