Specifications

ManualsBrandsCrestron ManualsComputer equipmentCSA-PWS10S-HUB

CSA-PWS10S-HUB

Introduction

The CSA-PWS10S-HUB power supply provides support for up to 10 Crestron

shades and features a built-in,

5-segment hub with network diagnostics capabilities. Local controls and indicators allow for easy testing of shades

without connecting to a control system. The CSA-PWS10S-HUB is convection cooled for silent operation and can

be surface mounted. It is also available pre-assembled in a CAEN-1X1 enclosure, model

CSA-PWS10S-HUB-CAEN-1X1, which can be surface mounted or recessed in a wall.

CSA-PWS10S-HUB Specifications

SPECIFICATION DETAILS

Load Rating

Total Shades Supported Provides power for up to (10) Crestron shades, each homerun to the power

supply

Output 24 Vdc

50 W per output LPS

350 W total continuous load

425 W for 2 minute on 2 minute off discontinuous shade load

Load Protection (10) Self resetting thermal fuses and (10) 4 A time lag fuses, Littelfuse JDYX2

0213 004 MXP (5 x 20 mm, 250 V, 4 A, time lag, cartridge) provided for each

50 W segment, (1) of each per output

Power Requirements 120–240 Vac, 50/60 Hz;

5 A maximum

Environmental

Installation Location Indoor use only

Temperature 32º to 104ºF (0º to 40ºC)

Humidity 10% to 90% RH (non-condensing)

Enclosure

CSA-PWS10S-HUB

CSA-PWS10S-HUB-

CAEN-1X1

Metal, gray, surface mount (indoor use only)

Includes CAEN-1X1, 16 gauge galvanized steel enclosure with vented gray steel

cover, surface mount or recessed in a wall (indoor use only)

Dimensions

CSA-PWS10S-HUB

Height

Width

Depth

CSA-PWS10S-HUB-

CAEN-1X1

Height

Width

Depth

7 9/16 in (194 mm)

12 15/16 in (330 mm)

2 11/16 in (68 mm)

16 9/16 in (421 mm)

16 1/8 in (409 mm)

4 7/16 in (113 mm)

Weight

CSA-PWS10S-HUB

CSA-PWS10S-HUB-

CAEN1x1

5.6 lb (2.6 kg)

15.0 lb (6.8 kg)

(Continued on the following page)

Crestron Electronics, Inc. Installation Guide – DOC. 7438C

15 Volvo Drive Rockleigh, NJ 07647 (2037987)

Tel: 888.CRESTRON 06.14

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Summary of content (16 pages)

PAGE 1
CSA-PWS10S-HUB Introduction The CSA-PWS10S-HUB power supply provides support for up to 10 Crestron® shades and features a built-in, 5-segment hub with network diagnostics capabilities. Local controls and indicators allow for easy testing of shades without connecting to a control system. The CSA-PWS10S-HUB is convection cooled for silent operation and can be surface mounted.
PAGE 2
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors CSA-PWS10S-HUB Specifications (Continued) SPECIFICATION Input Terminal (CSA-PWS10S-HUB-CAEN1X1 only) Line Power CSA-PWS10S-HUB CSA-PWS10S-HUBCAEN-1X1 ® DETAILS 18–10 AWG, 30 A, 600 V (1) Attached input power cable (~10 in long (254 mm)) with inline IEC 60320 C14 main power inlet; Mates with removable power cord (included) (1) Attached input power cable (~10 in long (254 mm)) with inline IEC 60320 C14 main power inlet; Connects to ac power
PAGE 3
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors Regulatory Compliance Conformité Reglementaire This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc. As of the date of manufacture, the CSA-PWS10S-HUB and CSA-PWS10S-HUB-CAEN-1X1 have been tested and found to comply with specifications for CE marking.
PAGE 4
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Top and Front Views) 1 1/4 in 1 1/2 in 5/8 in (32 mm) (39 mm) (16 mm) 15/16 in (24 mm) 1 1/4 in (32 mm) 5 11/16 in (145 mm) 2 1/2 in (64 mm) 1 5/16 in (33 mm) 2 5/16 in (58 mm) 1 1/4 in (32 mm) 2 9/16 in (65 mm) (4x) Ø 1 3/4 in (45 mm) Knockouts for 1 1/4 in (32 mm) Conduit 16 9/16 in (421 mm) 16 1/8 in (409 mm) 4 • Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide –
PAGE 5
Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Bottom View) 2 1/2 in (64 mm) 3 13/16 in (97 mm) (21x) Ø 7/8 in (23 mm) Knockouts for 1/2 in (13 mm) Conduit 1 1/4 in (32 mm) 1 1/4 in (32 mm) 11 1/4 in (286 mm) 1 1/4 in (32 mm) Typ. 5/8 in (16 mm) 15/16 in (24 mm) 14 3/8 in (365 mm) Installation Guide – DOC.
PAGE 6
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Side View) 1 3/4 in 1 in (45 mm) (26 mm) (8x) Ø~3/16 in (5 mm) Mounting Holes for #8 Wood Screws (Not Supplied) 10 13/16 in (275 mm) 8 in (203 mm) 5 7/16 in (138 mm) 15 13/16 in (402 mm) 1 7/16 in (36 mm) 2 1/2 in (64 mm) 2 1/4 in (58 mm) 4 1/4 in (108 mm) 4 7/16 in (113 mm) 6 • Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide – DOC.
PAGE 7
Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Front View, Cover Removed) Cresnet connectors are included. 2 1/4 in (58 mm) (4x) Ø~5/16 in (8 mm) Mounting Holes 10 7/8 in for #8 Wood Screws and #8 Large (276 mm) Flat Washers (Not Supplied) (4x) Ø5/8 in (16 mm) (4x) 7/16 in (12 mm) 10 15/16 in (277 mm) CSA-PWS10S-HUB ASSEMBLED IN COO Cable Tie Anchors 000 00 INPUT: 120-240 V~, 50/60 Hz , 5A MAX . I.T.
PAGE 8
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors CSA-PWS10S-HUB Overall Dimensions (Top, Front, and Bottom Views—Shown with Fuse Cover Removed) 1/4 in (7 mm) Offset 2 1/4 in (58 mm) IEC, 3 Conductor Male Cable, Aprox. 10” (254 mm) Long All Cresnet connectors and fuses are included.
PAGE 9
Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB CSA-PWS10S-HUB Overall Dimensions (Side View) 7 9/16 in (194 mm) 7 7/16 in (189 mm) 5/8 in (16 mm) 13/16 in (21 mm) Installation The enclosure must be installed by a licensed electrician in accordance with all national and local codes. CAUTION: Double pole/neutral fusing implemented. CAUTION: The CSA-PWS10S-HUB-CAEN-1X1 houses equipment that needs to be air-cooled. Therefore, mount in a well-ventilated area.
PAGE 10
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors Wiring Once the unit is properly secured to the mounting surface, the unit must be properly wired. Refer to the guidelines below for details. CAUTION: All power feeds must be protected by single pole listed circuit breaker or branch rated fuse no greater than 20 A. NOTE: Use copper conductors only—rated 75°C or better. NOTE: All wiring must be installed in accordance with all local and national electrical codes.
PAGE 11
Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB NOTE: Always disconnect ac power to the CSA-PWS10S-HUB before connecting network devices.
PAGE 12
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors Operation Once the power supply is mounted, wired, and powered up, a diagnostic test of the device and wiring should be performed. During the diagnostic test the power supply identifies connected shades and tests the wiring of the connected shades. Hold down the TEST button for 2 seconds to enter Test mode. The MSG LED blinks to indicate that the power supply is in Test mode.
PAGE 13
Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB Fuse Replacement CAUTION: For continued protection against risk of fire, replace only with the same type and rating of fuse. Fuse status is indicated by the green power LED on each associated channel. If the green LED is not illuminated it means that the fuse needs to be replaced. Fuses are to be serviced only by a trained service person and replaced with the same type and rating of fuse. Remove fuse cover from CSA-PWS10S-HUB before servicing.
PAGE 14
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors 3. For Connection Type, select USB. When multiple USB devices are connected, identify the CSA-PWS10S-HUB by entering “CSA-PWS10S-HUB” in the Model text box, the unit’s serial number in the Serial text box, or the unit’s hostname (if known) in the Hostname text box. 4. Click OK. Communications are confirmed when the device information is displayed.
PAGE 15
Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB Problem Solving Use the Right Wire To ensure optimum performance over the full range of the installation topology, use Crestron Certified Wire only. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire. Calculate Power CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty.
PAGE 16
Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.