Crestron DM-RMC-200-S/S2 DigitalMedia 8G™ Fiber Receiver & Room Controller 200 Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Important Safety Instructions WARNING: • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Regulatory Compliance Compliance Regulatory As of the date of manufacture, the DM-RMC-200-S and DM-RMC-200-S2 have been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Federal Communications Communications Commission Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Contents DigitalMedia 8G Fiber Receiver & Room Controller 200: DM-RMC-200-S/DM-RMC-200-S2 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications...............................................................................
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 DigitalMedia 8G Fiber Receiver & Room Controller 200: DM-RMC-200-S/DM-RMC-200-S2 Introduction The DM-RMC-200-S/DM-RMC-200-S2, hereinafter referred to simply as the DM® receiver unless otherwise indicated, provides an advanced one-box interface solution for a single display device as part of a complete Crestron® DigitalMedia™ system.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Features and Functions (Continued) Accepts any computer source from VGA to UXGA/WUXGA Scales the source to match the native resolution of virtually any popular video display or computer monitor Provides intelligent frame rate conversion Allows motion-adaptive de-interlacing or interlacing Allows adjustable overscan or underscan up to 7.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Multimedia Display Interface A single HDMI digital AV output port is provided on the DM receiver, supporting HD 1080p60 video and WUXGA computer signals with HDCP, Deep Color, 3D1, and multichannel HD lossless audio—all through one connection. The HDMI output can also handle DVI signals using an appropriate adapter or interface cable.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Video Wall Processing The DM receiver provides zoom capability on its output to display just a portion of the source image. Using this feature, multiple units may be combined to configure a high-definition video wall composed of up to 16 individual displays.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Applications The diagram below shows a DM-RMC-200-S in a standalone application. In this type of application, the DM-RMC-200-S is used with a DM 8G fiber transmitter such as the DM-TX-201-S (sold separately) and is not used with a DM switcher.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Specifications Specifications for the DM receiver are listed in the following table.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued) SPECIFICATION DETAILS Video Input Resolutions (Continued) 720 x 480 @ 30 Hz (480i) 720 x 576 @ 25 Hz (576i) 1920 x 1080 @ 25 Hz (1080i25) 1920 x 1080 @ 30 Hz (1080i30) plus any other resolution allowed by HDMI up to 165 MHz pixel clock Interlaced Scaler Output Resolutions Progressive 640 x 480 @ 60 Hz 720 x 480 @ 60 Hz (480p) 720 x 576 @ 50 Hz (576p) 800 x 600 @ 60 Hz 848 x 480 @ 60 Hz 1
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued) SPECIFICATION Audio (Continued) Performance (Analog) Amplifier Output Power8 Frequency Response S/N Ratio THD+N Stereo Separation Volume Gain Range (Analog) Communications DigitalMedia Ethernet USB Power Requirements Power Pack Minimum 2-Series Control System Update File9, 10 Environmental Temperature Humidity Heat Dissipation Enclosure Chassis Mounting Dimensions Height Width Depth Weig
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 DM-RMC-200-S/DM-RMC-200-S2 Specifications (Continued) SPECIFICATION DETAILS Available Accessories CBL Series Crestron Certified Interface Cables CNSP-XX Custom Serial Interface Cable CRESFIBER-CONNSC50UM-12 (DM-RMC-200-S only) CresFiber Fiber Optic Cable Connector CRESFIBER-SINGLE-SC (DM-RMC-200-S only) CresFiber Simplex Fiber Optic Cable Assembly, 50/125, SC CRESFIBER-SINGLESC-ARMORED (DM-RMC-200-S only) CresFiber ARMORED Simplex Fib
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Physical Description This section provides information on the connections, controls and indicators available on the DM receiver. DM-RMC-200-S/DM-RMC-200-S2 Physical View (Front Panel) DM-RMC-200-S DM-RMC-200-S2 10 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 DM-RMC-200-S/DM-RMC-200-S2 Physical View (Rear Panel) DM-RMC-200-S/DM-RMC-200-S2 Physical View (Top Panel) DM-RMC-200-S DM-RMC-200-S2 DM-RMC-200-S/DM-RMC-200-S2 Physical View (Bottom Panel) Operations & Installation Guide – DOC.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 DM-RMC-200-S/DM-RMC-200-S2 Overall Dimensions (Front and Side Panels without Mounting Bracket Installed) 7.60 in (193 mm) 7.45 in (190 mm) 7.92 in (201 mm) 7.54 in (192 mm) 1.05 in ( 27 mm) 1.46 in (37 mm) DM-RMC-200-S/DM-RMC-200-S2 Overall Dimensions (Front and Side Panels with Mounting Bracket Installed) 10.83 in (275 mm ) 1.30 in (33 mm) 4.93 in (126 mm) 3.30 in (84 mm) 1.23 in (32 mm) 1.53 in (39 mm) 1.62 in (41 mm) 1.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Front Panel) 1 2 3 4 5 6 DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Top Panel) DM-RMC-200-S 7 9 8 11 12 11 12 10 DM-RMC-200-S2 7 13 8 10 DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Bottom Panel) 14 Operations & Installation Guide – DOC.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 DM-RMC-200-S/DM-RMC-200-S2 Connectors, Controls & Indicators (Rear Panel) 19 20 21 22 Connectors, Controls & Indicators # CONNECTORS1, CONTROLS & INDICATORS 1 PWR LED 2 DM LINK LED 3 VIDEO LED 4 USB HID LED (1) Green LED, indicates a valid device connection and activity on the USB HID port 5 SETUP (LED and Button) (1) Red LED and (1) miniature recessed push button for Ethernet setup 6 RESET (1) Miniature recessed push button f
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 8 AUDIO OUT R, L (Line) 9 DM IN MMF/SC (DM-RMC-200-S only) (1) SC female optical fiber connector; DM 8G fiber input; Connects to DM 8G fiber output of a DM switcher, transmitter, or other DM device via CresFiber 8G multimode fiber optic cable3 10 DM IN LED (1) Green LED, indicates DM link status 11 LAN Pin 1 Amber LED Pin 8 Green LED DESCRIPTION (2
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 17 COM (1) 5-pin 3.5 mm detachable terminal block, bidirectional RS-232 port; Up to 115.2k baud, hardware and software handshaking support 18 IR 1-2 (1) 4-pin 3.5 mm detachable terminal block comprising two IR/Serial ports; IR output up to 1.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Setup Network Wiring When wiring the DM network, consider the following: Use Crestron Certified Wire. Use Crestron power supplies for Crestron equipment. CAUTION: Failure to use Crestron power supplies could cause equipment damage or void the Crestron warranty. Provide sufficient power to the system. For DigitalMedia 8G multimode fiber wiring, CresFiber 8G is recommended.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 When setting the IP ID, consider the following: The IP ID of each unit must match an IP ID specified in the SIMPL Windows program. Each device using IP to communicate with a control system must have a unique IP ID. Supplied Hardware The hardware supplied with the DM receiver is listed in the following table.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Mounting the DM-RMC-200-S/DM-RMC-200-S2 Standoffs (4) #06-32 x 1-1/4” (2007056) Screws (4) #06-32 x 3/4” (2009211) 2-Gang Electrical Box (Not Included) Mounting Bracket (2032478) Screws (4) #06-32 x 1/4” (2007215) Installing the Power Pack The included mounting bracket (2032478), which is used to attach the DM receiver to an electrical box (not included), provides a holder for the included power pack (2022484).
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Installing the Power Pack Power Pack Holder Tie-Wrap Holes (2) Screws (2) #06-32 x 1” (2007250) Power Pack (2022484) Installation of the power pack in the holder is shown below. Power Pack Installed in Holder of Mounting Bracket 20 DigitalMedia 8G Fiber Receiver 200: DM-RMC-200-S/S2 Operations & Installation Guide – DOC.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Hardware Hookup Make the necessary connections as called out in the following illustrations. Refer to “Network Wiring” on page 17. Apply power after all connections have been made. Hardware Connections for the DM-RMC-200-S (Top Panel) AUDIO OUT R, L (SPEAKER): Amplified Stereo Audio Output AUDIO OUT R, L (LINE): Stereo Unbalanced Line Level Audio Output LAN: 10BASE-T/ 100BASE-TX Ethernet to Local Network Device 24 V 2.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Hardware Connections for the DM-RMC-200-S/DM-RMC-200-S2 (Bottom Panel) HDMI OUT: Digital Video/ Audio Output USB HID: From USB HID-Compliant Device DIG IN: Software Programmable Digital Input COM: To RS-232 Device IR: To IR Controllable Device Hardware Connections for the DM-RMC-200-S/DM-RMC-200-S2 (Rear Panel) AUDIO OUT L, R (SPEAKER): Amplified Stereo Audio Output Ground RELAY 1-2: To Controllable Devices DIG IN: Software Programmable
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron Web site. To post a question or to view questions submitted to Crestron’s True Blue Support, log in at www.crestron.com/onlinehelp. First-time users must establish a user account to fully benefit from all available features.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 The system tree of the control system displays the DM receiver in the appropriate slot with a default IP ID as shown in the following illustrations. In the first example, the DM-RMC-200-S is used with the DMCO-40 output card in a DM-MD8X8 switcher. In the second example, the DM-RMC-200-S is used with the C2ENET-2 card in an Ethernet slot on the control system.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 NOTE: The ID code specified in the SIMPL Windows program must match the IP ID of each unit. Refer to “Identity Code,” which starts on page 17. Program Manager Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols. The symbol can be viewed by double-clicking the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1).
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, firmware) can be transferred to the device. In addition, the IP table of the device can be configured.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 3. Use the Address Book in Crestron Toolbox to create an entry for the DM receiver using the TCP connection type, and enter the IP address of the DM receiver. 4. icon); Display the “System Info” window of the DM receiver (click the communications are confirmed when the device information is displayed. USB Communication via DM Switcher To establish USB communication between the PC and the DM switcher: 1.
DigitalMedia 8G Fiber Receiver 200 Via LAN Port Crestron DM-RMC-200-S/S2 TCP/IP Communication via LAN Port of DM-RMC-200-S/DM-RMC-200-S2 DM-RMC-200-S/ DM-RMC-200-S2 24V MAX 2.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Firmware Firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron Web site as new features are developed after product releases. For details on upgrading, refer to the Crestron Toolbox help file. Check the Crestron Web site to find the latest firmware. (New users may be required to register to obtain access to certain areas of the site, including the FTP site.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. DM-RMC-200-S/DM-RMC-200-S2 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION PWR LED does not illuminate. Device is not receiving power. Verify power pack connections to the device and to the power outlet. PWR LED flashes.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 DM-RMC-200-S/DM-RMC-200-S2 Troubleshooting (Continued) TROUBLE Green LED on LAN port does not illuminate. Loss of functionality due to electrostatic discharge. POSSIBLE CAUSE(S) CORRECTIVE ACTION LAN network cable is not connected to the LAN port or to the 10BASE-T/ 100BASE-TX compatible device. Verify LAN network cable connection to the LAN port and to the compatible network device. LAN network cable is not the proper type.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 Future Updates As Crestron improves functions, adds new features and extends the capabilities of the DM-RMC-200-S/DM-RMC-200-S2, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron Web site periodically for manual update availability and its relevance.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed. PREAMBLE The licenses for most software are designed to take away your freedom to share and change it.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee. 2.
DigitalMedia 8G Fiber Receiver 200 Crestron DM-RMC-200-S/S2 modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6.
Crestron DM-RMC-200-S/S2 DigitalMedia 8G Fiber Receiver 200 This page is intentionally left blank. Operations & Installation Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 7246B (2031698) 10.12 Specifications subject to change without notice.
