Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the DM-TX-200 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Contents DigitalMedia™ CAT Transmitter 200: DM-TX-200 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 DigitalMedia™ CAT Transmitter 200: DM-TX-200 Introduction The DM-TX-200 is a DigitalMedia™ (DM) CAT transmitter and switcher that provides a convenient interface for computers and other high-resolution AV sources as part of a complete DigitalMedia system.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 DigitalMedia™ As the leader in HDMI and control system technologies, Crestron® has developed DigitalMedia, the first complete HD AV distribution system that takes HDMI to a higher level and allows virtually any mix of AV sources to be distributed throughout the home, office, school or virtually any other facility. DigitalMedia distributes uncompressed digital video and audio signals up to 450 feet (137 meters) using DM cable1.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 There are four options for connecting USB devices to the USB port on the DM-TX-200: 1. One mouse 2. One keyboard 3. One mouse and one keyboard connected through a USB hub 4. One composite USB device EDID Format Management The DM-TX-200 allows for management of the EDID (Extended Display Identification Data) information that passes between the display devices and input sources in the system.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 Applications The following diagram shows a DM-TX-200 in a basic application. DM-TX-200 in a Basic Application No LAN connection is required for the DM-TX-200 to transmit HDMI or USB in a point-to-point configuration. If you wish to use the control ports (IS, RS-232, Relay, Sense) from a control system, you can connect either LAN port (on the DM-RMC-100 or on the DM-TX-200) to the control system’s network.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Specifications Specifications for the DM-TX-200 are listed in the following table. DM-TX-200 Specifications SPECIFICATION DETAILS Video Switcher 2x1 combination digital/analog switch, Crestron QuickSwitch HD Input Signal Types HDMI, DVI1, DisplayPort Multimode1, RGB, component (YPbPr) 2, S-video (Y/C)2, composite2 Output Signal Type DM CAT (DigitalMedia over twisted pair copper wire) Formats HDMI, DVI v. 1.0, HDCP v.1.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 DM-TX-200 Specifications (Continued) SPECIFICATION DETAILS Video Input Resolutions (Continued) HDMI & DVI Interlaced 720 x 480 @ 30 Hz (480i), 720 x 576 @ 25 Hz (576i), 1920 x 1080 @ 25 Hz (1080i25), 1920 x 1080 @ 30 Hz (1080i30), plus any other resolution allowed by HDMI up to 165 MHz pixel clock RGB 640 x 480 @ 60 Hz, 720 x 480 @ 60 Hz (480p), 720 x 576 @ 50 Hz (576p), 800 x 600 @ 60 Hz, 848 x 480 @ 60 Hz, 1024 x 768 @ 60 Hz, 1280 x 720 @ 50 Hz
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 DM-TX-200 Specifications (Continued) SPECIFICATION DETAILS Audio (Continued) Performance (Analog) Frequency Response 20 Hz to 20 kHz ±0.75 dB S/N Ratio >90 dB, 20 Hz to 20 kHz A-weighted THD+N <0.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 DM-TX-200 Specifications (Continued) SPECIFICATION DETAILS Available Accessories (Continued) MP-WP130 Media Presentation Wall Plate – DB15HD Computer VGA with Mini-TRS Stereo Audio, Bulkhead MP-WP131 Media Presentation Wall Plate – DB15HD Computer VGA with Mini-TRS Stereo Audio, Breakout MP-WP140 Media Presentation Wall Plate – DVI-I with Mini-TRS Stereo Audio MP-WP150 Media Presentation Wall Plate – HDMI with Mini-TRS Stereo Audio MP-WP152
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Physical Description This section provides information on the connections, controls and indicators available on your DM-TX-200. DM-TX-200 Physical View (Bottom Ports Shown) DM-TX-200 Physical View (Top Ports Shown) Operations & Installation Guide – DOC.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 DM-TX-200 Overall Dimensions (Top View) 2.76 in (70 mm) 1 1.68 in (43 mm) 2 3 4 DM-TX-200 Overall Dimensions (Front View) 5 6 7 8 9 6.97 in (177 mm) 10 DM-TX-200 Overall Dimensions (Bottom View) 11 12 10 • DigitalMedia™ CAT Transmitter 200: DM-TX-200 13 Operations & Installation Guide – DOC.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Connectors, Controls & Indicators # CONNECTORS1, CONTROLS & INDICATORS 1 AUDIO 2 USB HID (1) USB Type A female; USB 1.1 host port for connection of a mouse, keyboard or other USB HID-compliant device 3 RGB (1) DB15HD female, RGB (VGA) or component YPbPr) video input2, 3 Formats: RGBHV, RGBS, RGSB, YPbPr; Input level: 0.5 to 1.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 3. Refer to the following table for the RGB connector pinouts. RGB Port PIN # RGB YPbPr S-VIDEO 1 R Pr C 2 G Y Y 3 B Pb 13 H 14 V COMPOSITE Comp 4. HDMI requires an appropriate adapter or interface cable to accommodate a DVI or DisplayPort Multimode signal. CBL-HD-DVI and CBL-DP-HD interface cables sold separately. 5.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Setup Network Wiring When wiring the DM network, consider the following: NOTE: DMNet wiring and Cresnet® wiring are not compatible. • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. • For DigitalMedia CAT wiring, use DM-CBL DigitalMedia Cable. Up to two DM Repeaters (model DM-DR, sold separately) may be required.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 Installation To prevent overheating, do not operate this product in an area that exceeds the environmental range listed in the table of specifications. The following tools and accessories are required for mounting a DM-TX-200 to a surface: • Phillips screwdriver (not supplied) • Metal mounting plate (included) • Two #04-40 x 3/16” pan head Phillips screws (included) Use the following procedure to mount the DM-TX-200 to a surface: 1.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Hardware Hookup Make the necessary connections as called out in the illustration that follows this paragraph. Refer to “Network Wiring” on page 13 before attaching the 4-position terminal block connector. Apply power after all connections have been made. When making connections to the DM-TX-200, note the following: • Use Crestron power supplies for Crestron equipment. • The included cable cannot be extended.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com. First-time users will need to establish a user account.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 2. The system tree of the control system displays the device in the appropriate slot with an IP ID as shown in the following illustration. C2Net Device, Slot 8 (Using Input Card in DM Switcher) NOTE: Alternatively, the DM-TX-200 can be dragged directly to a card such as the C2ENET-2, in the Ethernet slot of the control system, when it is to be used without a DM switcher. C2Net Device, Slot 8 (Using Ethernet Slot on Control System) 3.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 “Device Settings: Crestron DM-TX-200” Window 5. Program Manager The ID code specified in the SIMPL Windows program must match the IP ID of each unit. Refer to “Identity Code” on page 13 Program Manager is the view where programmers “program” a Crestron control system by assigning signals to symbols. The symbol can be viewed by double clicking on the icon or dragging it into Detail View.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, firmware) can be transferred to the device.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 configuration, from Crestron Toolbox, display the “System Info” window icon) and select the DM-TX-200 entry from the Address (click the Book. Select Functions | Ethernet Addressing and enter the new IP address, IP mask and default router of the DM-TX-200. NOTE: If the DM-TX-200 is in a non-DHCP environment, a default IP address (192.168.1.232) can be assigned by holding down its SETUP button while applying power.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 IP Configuration For Ethernet connections, display the “System Info window (click the icon) and select the Functions menu to display actions that can be performed on the DM-TX-200. When using the DM-TX-200 with a DM-RMC-100 (i.e. without a DM switcher), be sure to use Crestron Toolbox to create the DM-TX-200 IP table. 1. Use the Device Discovery Tool to find the IP address of the DM-TX-200.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. DM-TX-200 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Device is not communicating with the network. Use Crestron Toolbox to poll the network. Verify network connection to the device.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 Refer to the following for maximum DM cable lengths.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed. PREAMBLE The licenses for most software are designed to take away your freedom to share and change it.
DigitalMedia™ CAT Transmitter 200 Crestron DM-TX-200 You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee. 2.
Crestron DM-TX-200 DigitalMedia™ CAT Transmitter 200 modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 6741C (2024102) 04.10 Specifications subject to change without notice.
