Crestron FTI-PWR-D FlipTop Power Center International Version Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the FTI-PWR-D-B and FTI-PWR-D-BALUM have been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron FTI-PWR-D FlipTop Power Center - International Version Contents FlipTop Power Center - International Version: FTI-PWR-D 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications....................................................................................................
Crestron FTI-PWR-D FlipTop Power Center - International Version FlipTop Power Center International Version: FTI-PWR-D Introduction The FTI-PWR-D provides an elegant connectivity solution in a stylish flush mount tabletop package. Beneath the "FlipTop" lid, the cable storage compartment keeps interface cables at the ready for plugging in computers, AV sources, and a host of other devices.
FlipTop Power Center – International Version Crestron FTI-PWR-D Applications The following diagram shows an FTI-PWR-D in a lecture hall application. FTI-PWR-D in a Lecture Hall Application Specifications Specifications for the FTI-PWR-D are listed in the following table.
Crestron FTI-PWR-D FlipTop Power Center - International Version Physical Description This section provides information on the connections, controls, and indicators available on your FTI-PWR-D. FTI-PWR-D Physical View FTI-PWR-D Overall Dimensions (Top View) 216 mm (8.50 in 173 mm (6.83 in) 169 mm (6.67 in) Operations & Installation Guide – DOC.
FlipTop Power Center – International Version Crestron FTI-PWR-D FTI-PWR-D (Bottom View) FTI-PWR-D Overall Dimensions (Front View) 176 mm (6.91 in) 203 mm (8.00 in) FTI-PWR-D Overall Dimensions (Rear View) FTI-PWR-D Overall Dimensions (Side View) 76 mm (2.98 in) 116 mm (4.57 in) 142 mm (5.58 in) 205 mm (8.09 in) 4 • FlipTop Power Center – International Version: FTI-PWR-D Operations & Installation Guide – DOC.
Crestron FTI-PWR-D FlipTop Power Center - International Version FTI-PWR-D (Front Face View) 1 FTI-PWR-D (Bottom View) 2 Connectors, Controls, & Indicators # CONNECTORS, CONTROLS, & INDICATORS 1 MAX 250V~50/60Hz 10A DESCRIPTION (2) Grounded AC sockets, AC power pass-through outlets Specify Socket Type: PWR-AU-B (Australia/China), PWR-EU-B (Europe "Schuko"), PWR-FR-B (France), PWR-IT-B (Italy), PWR-UK-B (UK); Maximum Load: 10 Amps @ 250 Volts AC, 50/60 Hz 2 MAX 250V~50/60Hz 10A (1) IEC socket Pas
FlipTop Power Center – International Version Crestron FTI-PWR-D Setup Installation NOTE: To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the specifications table. Consideration must be given if installed inside a closed desk or in a closed podium since the operating ambient temperature of these environments may be greater than the room ambient temperature.
Crestron FTI-PWR-D FlipTop Power Center - International Version Cable Support Plate Installation When selecting cables for installation in the FTI-PWR-D, cable connector length and strain relief diameter are important considerations. • If the connector is too long, it can interfere with cover operation. • If the width of the cable strain relief is too similar to the bushing inside diameter, the bushing can trap the cable. NOTE: Do not use the cable support plate without the bushings.
FlipTop Power Center – International Version Crestron FTI-PWR-D Cables Threaded Through the Cable Plate NOTE: Ensure that any cables you install have sufficient clearance to enable smooth movement. Allow approximately 1 meter (40 inches) from the top surface of the FlipTop box. Surface Mounting The FTI-PWR-D is designed to mount in a horizontal surface, such as a desk top, lectern, or podium. The following diagram illustrates the required opening size to accommodate the FTI-PWR-D.
Crestron FTI-PWR-D FlipTop Power Center - International Version Mounting Parts Supplied DESCRIPTION PART NUMBER QUANTITY Screws, #06-32 x 3/16” (~5 mm), Pan Head, Phillips 2007204 8 Screws, #10-32 x 2” (~51 mm), Pan Head, Phillips 2007293 4 Mounting Bracket 2013224 2 1. Install the eight supplied #06-32 x 3/16” (~5 mm) screws (2007204) on the front and back of the unit. Do not fully tighten the screws. These will be used to secure the front and back mounting brackets.
FlipTop Power Center – International Version Crestron FTI-PWR-D Mounting Bracket Installation 5. Turn the four #10-32 screws equally until they contact the underside of the mounting surface enough to secure the unit. DO NOT OVER-TIGHTEN. CAUTION: Do not over-tighten the #10-32 screws as this may damage the surface and/or the unit. FTI-PWR-D (Mounting Brackets Installed) 10 • FlipTop Power Center – International Version: FTI-PWR-D Operations & Installation Guide – DOC.
Crestron FTI-PWR-D FlipTop Power Center - International Version Hardware Hookup Make the necessary connections as called out in the following illustration. Hardware Connections for the FTI-PWR-D MAX 250V ~50/60 HZ 10A: MAX 250V ~50/60 HZ 10A: IEC-320 Electrical Appliance Connector Connects to Appropriate International Power Receptacle NOTE: Apply power after all connections have been made.
FlipTop Power Center – International Version Crestron FTI-PWR-D Operation The spring-loaded lid is opened by pressing briefly and releasing it. Cables are stored neatly beneath the lid when not in use to keep out debris and dust. The lid opens 135 degrees, allowing full access to cables and power inside.
Crestron FTI-PWR-D FlipTop Power Center - International Version Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. FTI-PWR-D Troubleshooting TROUBLE POSSIBLE CAUSE(S) Device connected to the AC socket is not working. CORRECTIVE ACTION Lack of, or insufficient, power to AC socket. Provide appropriate power to the line cord.
FlipTop Power Center – International Version Crestron FTI-PWR-D Appendix: International Power Receptacles PART NUMBER DESCRIPTION COUNTRIES 6501271 PWR-AU-B POWER RECEPTACLE, AUSTRALIA, 250V, 10A, BLK Australia, Fiji, New Zealand, Papua New Guinea 6501272 PWR-EU-B POWER RECEPTACLE, EUROPE "SCHUKO", 250V, 16A, BLK Austria, Azerbaijan, Belarus, Bosnia and Herzegovina, Brunei, Bulgaria, Burundi, Cape Verde, Chad, Croatia, Czech Republic, Egypt, Eritrea, Finland, Georgia, Germany, Greece, Greenland, G
Crestron FTI-PWR-D FlipTop Power Center - International Version Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations & Installation Guide – DOC. 6797B (2023946) 06.10 Specifications subject to change without notice.
