Specifications

ManualsBrandsCrestron ManualsComputer equipmentinfiNET Gateway C2N-MNETGW

infiNET™ DIMMERS

Introduction

Features and Functions

The CLW-DIM1RF (-DIM1RF) and CLW-DIM4RF

(-DIM4RF) are stand-alone wall box dimmers that can

also act as wireless infiNET™ devices that report to a

Crestron

control processor through an infiNET gateway

such as the Crestron C2N-MNETGW. The -DIM1RF and

-DIM4RF have three preset lighting levels that can be

adjusted. For more information, refer to the latest version

of the infiNET Dimmers Operations Guide (Doc. 6396)

which is available from the Crestron website

(www.crestron.com/manuals).

These dimmers are part of Crestron’s line of lighting

products using infiNET mesh network technology.

infiNET technology is “Wi-Fi” friendly and provides fault

tolerance and increased effective signal strength as

network devices are added.

Crestron Electronics, Inc. Installation Guide – DOC. 6292C

15 Volvo Drive Rockleigh, NJ 07647 (2011321)

Tel: 888.CRESTRON 03.09

Up to 30 infiNET devices (including C2N-MNETRPT

infiNET Repeaters) can communicate with one

C2N-MNETGW Gateway. If more devices are needed,

more C2N-MNETGW gateways may be added to a

Cresnet

network.

The infiNET dimmers operate on the 2.4 GHz “ISM

band” (2400 MHz to 2483.6 MHz) at 10 mW. The output

power of these devices allow RF signals to travel

approximately 150 feet indoors and 250 feet outdoors

(subject to site-specific conditions) without the use of

repeaters or other infiNET devices. The range is

dependent on construction of the building, obstructions,

and RF interference from other devices. The location of

the dimmer is an important factor in determining RF

performance. Adding more infiNET devices or repeaters

to the network effectively increases the range, strength,

and reliability of the network.

The -DIM1RF and -DIM4RF feature a three-position

mode selection switch. For more information, refer to the

latest version of the infiNET Dimmers Operations Guide

(Doc. 6396) which is available from the Crestron website.

In the absence of control system communications, the

dimmer can still be used to control the attached load.

The CLW-DIMS1RF (-DIMS1RF) and CLW-DIMS4RF

(-DIMS4RF) are similar to the -DIM1RF and -DIM4RF

(respectively) with the added capability of working with

one or more slave units (CLW-SLVD1RF) in a multi-

dimmer / single circuit application.

The CLW-SLVD1RF (-SLVD1RF) is a slave unit that

when used in conjunction with the -DIMS1RF or

-DIMS4RF acts as an additional dimmer control point in a

multi-dimmer / single circuit application. It does not

connect to a Cresnet system and cannot be used without a

-DIMS1RF or -DIMS4RF. The -SLVD1RF does not have

a mode selection switch. It will emulate the RUN mode of

the -DIMS1RF (even if connected to a -DIMS4RF) unless

the mode selection switch of the master is set to “OFF”.

For more information, refer to the latest version of the

infiNET Dimmers Operations Guide (Doc. 6396) which is

available from the Crestron website.

These dimmers are available in a variety of colors and

textures. The table below shows the availability.

Available Colors/Textures

COLOR/

TEXTURE

MODEL NUMBER

SUFFIX

MATCHING LUTRON

FACEPLATE

White W Not Applicable

Smooth White W-S CW-1-WH

Almond A CW-1-LA

Smooth Almond A-S CW-1-LA

Black B Not Applicable

Smooth Black B-S CW-1-BL

Specifications

Following are specifications for the -DIM1RF, -DIM4RF,

-DIMS1RF, -DIMS4RF, and -SLVD1RF.

CLW-DIM1RF/-DIM4RF, CLW-DIMS1RF/-DIMS4RF, &

CLW-SLVD1RF Specifications

SPECIFICATION DETAILS

Power Requirements Line Power, 120 VAC, 60 Hz

Operating Frequency 2400 MHz to 2483.6 MHz

(802.15.4 compliant)

RF Output Power 10 mW

Operating Ranges¹

Typical Distance

Indoors

(without repeater)

Typical Distance

Outdoors

150 ft

250 ft

(subject to site-specific

conditions)

Default MNET ID -DIM1RF/-DIM4RF: 01/01

-DIMS1RF/-DIMS4RF: 01/01

Switch Type Dimmer

Load Type Incandescent, Tungsten-

Halogen, Magnetic Low Voltage

2-Series Control System

Update File

2,3

Version 3.154 or later

Load Ratings

Incandescent/Tungsten-

Halogen

-DIM1RF/-DIM4RF: 1000W

-DIMS1RF/-DIMS4RF: 1000W

-SLVD1RF: N/A

(continued on following page)

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Summary of content (12 pages)

PAGE 1
infiNET™ DIMMERS Introduction Features and Functions The CLW-DIM1RF (-DIM1RF) and CLW-DIM4RF (-DIM4RF) are stand-alone wall box dimmers that can also act as wireless infiNET™ devices that report to a Crestron® control processor through an infiNET gateway such as the Crestron C2N-MNETGW. The -DIM1RF and -DIM4RF have three preset lighting levels that can be adjusted. For more information, refer to the latest version of the infiNET Dimmers Operations Guide (Doc.
PAGE 2
infiNET™ DIMMERS CLW-DIM1RF/-DIM4RF, CLW-DIMS1RF/-DIMS4RF, & CLW-SLVD1RF Specifications (continued) SPECIFICATION DETAILS Load Ratings (continued) Magnetic Low Voltage 5 4 Line voltage connections are made at the rear of the dimmer.
PAGE 3
infiNET™ DIMMERS Physical view of CLW-DIM4RF/-DIMS4RF (clockwise from top; Top, Side, and Front) FCC ID: EROCWD1011 1.75 in (4.45 cm) Compliance Statement (Part 15.19 ) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 2.38 in (6.03 cm) 1.88 in (4.77 cm) RUN SET 2.70 in (6.86 cm) 4.13 in (10.48 cm) OFF 1.50 in (3.
PAGE 4
infiNET™ DIMMERS • • Inner Sections of Multiganged Switches (CLW-DIM4RF shown) Wallboxes: Devices mount in standard wallboxes. For easy installation, Crestron recommends using 3 ½” deep wallboxes. Several devices can be installed in one wall box (multigang). This requires the removal of side sections (refer to diagram on page 4) and the derating of the dimming device. For a smooth appearance, one-piece multigang faceplates (not supplied) can be installed.
PAGE 5
infiNET™ DIMMERS 3. Push all power wires back into the wallbox and fasten the device to the wallbox with the provided screws. 4. Attach decorative faceplate. 5. Restore power at the circuit breaker. Installation WARNING: Turn off power at the circuit breaker. Installing with power on can result in serious personal injury and damage to the device. NOTE: The -DIM1RF, -DIM4RF, -DIMS1RF, -DIMS4RF, and -SLVD1RF require a neutral wire in the wallbox for operation.
PAGE 6
infiNET™ DIMMERS Testing a -SLVD1RF Testing NOTE: The device may be warm to the touch during operation. This is normal. Test the installation by setting the dimmer’s mode selection switch (shown in the following diagrams) to the “RUN” position and perform either of the following steps (depending on the dimmer model).
PAGE 7
infiNET™ DIMMERS NOTE: Holding the button for a significant time after the first flash may enter other modes. If this is not desired, return the mode selection switch to the “OFF” position without releasing the button and repeat step 2. After approximately ten seconds, the LED will start to blink slowly and the dimmer will attempt to acquire with a C2N-MNETGW that is in the Acquire mode. The device is acquired when the LED stops blinking and lights at the LOW setting.
PAGE 8
infiNET™ DIMMERS Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PAGE 9
infiNET™ DIMMERS Appendix: Wiring Diagrams Following are wiring diagrams for circuits that may be found when installing infiNET dimmers: Stand-Alone Installations Figure 1: Wiring a CLW-DIM(S)XRF (CLW-DIMS1RF shown) • Since a -DIMSXRF is installed without a slave, the blue lead of the -DIMS1/4RF must be capped. If a neutral is not present in the wallbox, the wiring shown in the following diagram can be used.
PAGE 10
infiNET™ DIMMERS To continue a circuit past a switched light fixture to one or more duplex receptacles, connect the dimmer as shown in the following diagram. Figure 3: Adding a Duplex Receptacle Past a Switched Light Fixture Master-Slave Installations Figure 4: Wiring a CLW-DIMSXRF (CLW-DIMS4RF shown) with a CLW-SLVD1RF If a neutral is not present in the wallbox, the wiring methods shown in the following diagrams can be used when wiring a -DIMSXRF with -SLVD1RF devices.
PAGE 11
infiNET™ DIMMERS In this configuration: • The white wire from the DIMSXRF to the load is coded HOT. • The white wire of the -SLVD1RF must be capped. • The white line between -DIMSXRF and the -SLVDRF must be capped on both ends. • The minimum load requirement is 100W. • Bulb noise may be present even when the load is off. • The LED on an attached -SLVD1RF slave unit will not function. • Circuits with small magnetic low-voltage loads may not work.
PAGE 12
infiNET™ DIMMERS This page is intentionally left blank. 12 • infiNET™ Wall Box Dimmer : CLW-DIM1/4RF, DIMS1/4RF, & SLVD1RF Installation Guide – DOC.