Crestron MMK-4000L & WMKM-4000L Mud Mount Kits Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2004 Crestron Electronics, Inc.
Crestron MMK-4000L & WMKM-4000L Mud Mount Kits Mud Mount Kits: MMK-4000L & WMKM-4000L Description Mud Mount Kits are the preferred mounting option for the Crestron Isys® TPS-4000L series of lectern/wall-mounted video touchpanel when cutouts made in the drywall for touchpanel installation are too large. These kits provide support for additional plastering that can be applied to hide large irregularities in the touchpanel cutout. There are two Mud Mount Kits. The MMK-4000L is a pre-construction accessory.
Mud Mount Kits Crestron MMK-4000L & WMKM-4000L The dimensions of the MMK-4000L/WMKM-4000L are shown below. Dimensional Drawing 0.38 in (0.95 cm) 5.91 in (15.01 cm) 8.99 in (22.84 cm) 0.38 in (0.95 cm) 0.06 in (0.15 cm) 12.63 in (32.08 cm) MOUNTING PLATE FOR WMKM-4000L FASTENER PLATE FOR WMKM-4000L AND MMK-4000L 9.34 in (23.73 cm) 12.79 in (32.49 cm) 0.05 in (0.13 cm) 2.26 in (5.
Crestron MMK-4000L & WMKM-4000L Mud Mount Kits Installation This section provides an installation procedure for each Mud Mount Kit. The procedure for the MMK-4000L starts below and the “WMKM-4000L Procedure” starts on page 5. MMK-4000L Procedure The procedure in this section provides the necessary steps for the assembly of the MMK-4000L to either the PMK-4000L or BB-4000L.
Mud Mount Kits Crestron MMK-4000L & WMKM-4000L 2. Slide a push-on fastener over each pin of the PMK-4000L (or BB-4000L) to loosely secure the fastener plate and the mounting plate. Do not push the push-on fasteners all the way down onto the pins. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. 3. Use the second fastener plate and repeat steps 1 and 2 using the lower two PMK-4000L (or BB-4000L) pins.
Crestron MMK-4000L & WMKM-4000L Mud Mount Kits 7. Use four standard drywall screws (length should not exceed drywall thickness by more than ½ inch) to secure the mud ring plate to the rest of the assembly. The screws pass through the clearance holes in the PMK-4000L (or BB-4000L) and are secured in the extruded holes of the fastener plates. 8. Verify that the mud ring plate is level. NOTE: Do not over tighten screws. Doing so may over-dimple or rip the mud ring plate. 9.
Mud Mount Kits Crestron MMK-4000L & WMKM-4000L 2. Slide a push-on fastener over each pin on the fastener plate to loosely secure the fastener plate and the mounting plate. Do not push the pushon fasteners all the way down onto the pins. Slide them on enough to keep the fastener plate and mounting plate as one fastener/mounting plate assembly. 3. Use the second fastener plate and repeat steps 1 and 2 using the lower two PMK-4000L pins. 4.
Crestron MMK-4000L & WMKM-4000L 9. Mud Mount Kits When the fastener/mounting plate assembly is in position, bend the top two flanges of the mud ring upward (approximately 90 degrees) and the bottom two flanges downward (approximately 90 degrees). Refer to the illustration after this step. NOTE: Fastener/mounting plate assembly will have slight play; this is normal. It allows for minor adjustments to the TPS-4000L during installation. Bend Flanges 10.
Mud Mount Kits Crestron MMK-4000L & WMKM-4000L Further Inquiries If after reviewing this Installation Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: • In the US and Canada, call Crestron’s corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. • In Europe, call Crestron International at +32-15-50-99-50. • In Asia, call Crestron Asia at +852-2341-2016.
Crestron MMK-4000L & WMKM-4000L Mud Mount Kits Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Installation Guide – DOC. 6303 10.04 Specifications subject to change without notice.
