Crestron PSPHD PROCISE™ High Definition Professional Surround Sound Processor Operations Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Regulatory Compliance As of the date of manufacture, the PSPHD has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron PSPHD PROCISE™ Surround Sound Processor Contents PROCISE™ High Definition Professional Surround Sound Processor: PSPHD 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.....................................................................................................
PROCISE™ Surround Sound Processor Crestron PSPHD Problem Solving ...................................................................................................................... 61 Troubleshooting......................................................................................................... 61 Check Network Wiring.............................................................................................. 61 Reference Documents..............................................................
Crestron PSPHD PROCISE™ Surround Sound Processor PROCISE™ High Definition Professional Surround Sound Processor: PSPHD Introduction The PROCISE™ High Definition Professional Surround Sound Processor (PSPHD) from Crestron® is a professional 7.3 surround sound audio processor designed for high-end home theaters and corporate boardrooms. Advanced features include Audyssey MultEQ® XT*, Dolby® TrueHD 7.1 and DTS-HD Master Audio™ 7.
PROCISE™ Surround Sound Processor Crestron PSPHD Features and Functions (Continued) • • • • • • • • • • • • • • • • Dynamic Volume™ solves the problem of radically fluctuating volume levels Pure mode bypasses all signal processing to provide a pure signal path for critical listening QuickSwitch HD digital switching achieves fast switching of HDMI audio and video Smart HDCP management ensures reliable handling of digital HD content, and compatibility with a wide range of devices Discrete output channel s
Crestron PSPHD PROCISE™ Surround Sound Processor Versatile signal steering throughout affords extensive customization for any application without the need for additional outboard signal routing equipment. The PSPHD features native Crestron system integration via Cresnet and Ethernet affords unmatched control capability using any Crestron touchpanel, handheld remote, or e-Control®. Full setup and configuration is facilitated through the front panel or PROCISE Tools software.
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD in a Residential Home Theater Application, 2-D View 4 • PROCISE™ Surround Sound Processor: PSPHD Operations Guide – DOC.
Crestron PSPHD PROCISE™ Surround Sound Processor PSPHD in a Conferencing Boardroom with Audio and Video Conferencing Operations Guide – DOC.
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD in a Conferencing Boardroom with Audio and Video Conferencing, 2-D View 6 • PROCISE™ Surround Sound Processor: PSPHD Operations Guide – DOC.
Crestron PSPHD PROCISE™ Surround Sound Processor PSPHD in a Boardroom without Conferencing Operations Guide – DOC.
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD in a Boardroom without Conferencing, 2-D View HD Cable Box HDMI Out PSPHD Processor Digital Blu-Ray Disc Player HDMI Out Laptop DVI Out HDMI In 1 HDMI In 2 HDMI In 3 HDMI In 4 HDMI In 5 HDMI In 6 HDMI Out LCD Display Optical In 1 Optical In 2 Optical In 3 Optical In 4 Optical In 5 Optical In 6 Left Right B Right Center S Left S Right B Left SPDIF In 1 SPDIF In 2 SPDIF In 3 SPDIF In 4 SPDIF In 5 SPDIF In 6 AES/EBU In PROAMP-7X400 Amplifier
Crestron PSPHD PROCISE™ Surround Sound Processor PSPHD in an Auditorium Operations Guide – DOC.
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD in an Auditorium, 2-D View DSS Receiver HDMI Out Projector PSPHD Processor Composite S-Video Y/Pb/Pr HDMI Digital Blu-Ray Disc Player HDMI Out Laptop DVI Out HDMI Out HDMI In 1 HDMI In 2 HDMI In 3 HDMI In 4 HDMI In 5 HDMI In 6 Optical In 1 Optical In 2 Optical In 3 Optical In 4 Optical In 5 Optical In 6 Left Right S Left S Right Center SPDIF In 1 SPDIF In 2 SPDIF In 3 SPDIF In 4 SPDIF In 5 SPDIF In 6 AES/EBU In PROAMP-7X400 Amplifier Analo
Crestron PSPHD PROCISE™ Surround Sound Processor Internal Block Diagram The following diagram represents the abilities of the PSPHD. Internal Block Diagram of the PSPHD 1 2 3 4 5 6 7 8 9 10 1 6 1 4 1 Stereo Audio Stereo Audio Stereo Audio Stereo Audio Stereo Audio 10 x 1 Analog Audio Switch Stereo Audio 7.3 Program Audio Stereo Audio A/D 7.3 Mixed Tone Control Volume Control Main Out 7.
PROCISE™ Surround Sound Processor Crestron PSPHD Specifications Specifications for the PSPHD are listed in the following table. PSPHD Specifications SPECIFICATION DETAILS Audio – General Features 27 selectable source inputs plus built-in noise generator, 7.1 Dolby® Digital/DTS® surround sound decoder, 7.
Crestron PSPHD PROCISE™ Surround Sound Processor PSPHD Specifications (Continued) SPECIFICATION DETAILS Audio – Surround Sound Decoding Modes None, Stereo, Dolby Pro Logic IIx Movie, Dolby Pro Logic IIx Music, DTS Neo:6 Cinema, DTS Neo:6 Music, Two Channel Steering – Surround, Two Channel Steering – Rear, Multi-Channel Stereo (Party), Cathedral, Hall, Stadium, Jazz Club, Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, DTS®, DTS-ES Matrix, DTS-ES Discrete, DTS 96/24, DTS-HD Master Au
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD Specifications (Continued) SPECIFICATION DETAILS Audio – Downmix L/R Output Level -80dB to +20dB, adjustable from 0% to 100%, plus mute Mono Output Level -80dB to +20dB, adjustable from 0% to 100%, plus mute Bass Control ±12.0 dB per output Treble Control ±12.0 dB per output Audio – 3-Channel Input Mixer Mix Level -80.0 to 0.
Crestron PSPHD PROCISE™ Surround Sound Processor PSPHD Specifications (Continued) SPECIFICATION DETAILS Video Features 6x1 digital switcher, HDCP management, resolution management, Crestron QuickSwitch HD Input Signal Types 1 1 HDMI, DVI , DisplayPort Multimode Output Signal Types HDMI, DVI1 Formats HDMI w/Deep Color, DVI, HDCP v.1.
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD Specifications (Continued) SPECIFICATION DETAILS Environmental Temperature 41° to 104°F (5° to 40°C) Humidity 10% to 90% RH (non-condensing) Heat Dissipation 225 BTU/Hr Enclosure Chassis Metal, vented sides, ultra-quiet speedcontrolled fan cooling Front Panel Aluminum with plastic overlay Mounting Freestanding or 3U 19-inch rack-mountable (detachable feet and rack ears included) Dimensions Height 5.74 in (146 mm) with feet 5.
Crestron PSPHD PROCISE™ Surround Sound Processor Physical Description This section provides information on the connections, controls and indicators available on your PSPHD. PSPHD Physical View (front) PSPHD Physical View (rear) Operations Guide – DOC.
PROCISE™ Surround Sound Processor Crestron PSPHD PSPHD Overall Dimensions 17.08 in (434 mm) 17.28 in (439 mm) 13.89 in (353 mm) 14.75 in (375 mm) 1 3 8 9 11 16 2 5.20 in (133 mm) 5.74 in (146 mm) 4 18 5 6 20 7 21 10 22 12 23 13 24 14 25 15 27 17 28 29 30 19 31 26 18 • PROCISE™ Surround Sound Processor: PSPHD Operations Guide – DOC.
Crestron PSPHD PROCISE™ Surround Sound Processor Connectors, Controls & Indicators # CONNECTORS*, CONTROLS & INDICATORS DESCRIPTION 1 SELECTION KNOB Rotary encoder with integral pushbutton, used to navigate and select various menu options and adjust values 2 STANDBY BUTTON & LED (1) pushbutton and red LED, places PSPHD (and PROAMP if connected) into “Standby” mode (all outputs turned off) 3 DISPLAY (LEFT) The left side of the PSPHD contains a Vacuum Fluorescent Display (VFD) that shows informat
PROCISE™ Surround Sound Processor Crestron PSPHD Connectors, Controls & Indicators (Continued) # CONNECTORS*, CONTROLS & INDICATORS 9 DISPLAY BUTTON 10 MICROPHONE, RESET BUTTON, and USB PORT (behind removable front panel) DESCRIPTION (1) pushbutton, normally sets the front panel display brightness; pressing DISPLAY and HOME simultaneously for 5 seconds enters the Installer menu (1) 3-pin mini-XLR Jack: Input for calibrated microphone (part of CSSTK Surround Sound Tuning Kit, sold separately) RESET
Crestron PSPHD PROCISE™ Surround Sound Processor Connectors, Controls & Indicators (Continued) # CONNECTORS*, CONTROLS & INDICATORS 15 AMPLIFIER BUTTON (1) pushbutton, enables display of amplifier status (if PROAMP is connected) 16 VOLUME KNOB (1) rotary encoder with integral pushbutton, turn to adjust master volume level, press to display master volume level 17 MUTE BUTTON & LED (1) pushbutton and red LED, mutes all outputs 18 DIGITAL SOURCES (4) JIS F05 female (TOSLINK) optical fiber connec
PROCISE™ Surround Sound Processor Crestron PSPHD Connectors, Controls & Indicators (Continued) # CONNECTORS*, CONTROLS & INDICATORS 23 MULTI-CHANNEL SOURCE FRONT L/R, SURROUND L/R, BACK L/R, CENTER, SUB (8) RCA female; Unbalanced line-level 7.
Crestron PSPHD PROCISE™ Surround Sound Processor Connectors, Controls & Indicators (Continued) * Operations Guide – DOC. 6837B # CONNECTORS*, CONTROLS & INDICATORS 30 100-240V ~50-60Hz 65W 31 GROUND DESCRIPTION (1) IEC Male C14 male chassis plug; Mates with removable power cord (included) (1) 6-32 screw, chassis ground lug Interface connectors for the NET and MIXER INPUT ports are provided with the unit.
PROCISE™ Surround Sound Processor Crestron PSPHD Setup Network Wiring When wiring the Cresnet® and Ethernet network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators).
Crestron PSPHD PROCISE™ Surround Sound Processor • If an IP ID is set, Cresnet communications with the PSPHD are disabled. Installation Ventilation The PSPHD should be used in a well-ventilated area. The venting holes should not be obstructed under any circumstances. To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications.
PROCISE™ Surround Sound Processor Crestron PSPHD Ear Attachment for Rack Mounting 4. Stacking Repeat procedure (steps 1 through 3) to attach the remaining ear to the opposite side. Four “feet” are integrated into the PSPHD so that if the unit is not rack mounted, the feet can provide stability when the unit is placed on a flat surface or stacked. NOTE: No more than two PSPHD units should be stacked. NOTE: If the PSPHD is to be rack mounted, the feet should be removed with a #2 Phillips screwdriver.
Crestron PSPHD PROCISE™ Surround Sound Processor NOTE: A USB port is concealed behind the label cover on the front panel. The USB port is used to connect with a PC and provides a console connection to the PSPHD. A microphone jack is also concealed behind the front panel’s label cover. This jack is used to connect the microphone that is included with the available Crestron Professional Surround Sound Tuning Kit.
PROCISE™ Surround Sound Processor PROCISE Amplifier Connections Crestron PSPHD Refer to the following diagram to properly connect the PSPHD to a PROCISE amplifier. Connect PSPHD to PROCISE Amplifier NOTE: For optimum performance when connecting to a PROCISE amplifier, Crestron recommends the optional CBL-PRO-XLR-2 (two-foot cable length) or CBL-PRO-XLR-6 (six-foot cable length) cable kit to connect to the PSPHD or other pre-amplifier.
Crestron PSPHD Mixer Input Connections PROCISE™ Surround Sound Processor Three balanced/unbalanced mixer inputs are provided, utilizing three-pin terminal block connectors. For connection details, refer to the following table and diagrams.
PROCISE™ Surround Sound Processor Crestron PSPHD Configuration After making all hardware connections to the PSPHD, the PSPHD must be configured for operation. Basic configuration is performed with the Installer menu. Advanced audio configuration options such as delay, levels, and equalization are performed with Crestron Toolbox’ PROCISE Tools utility. Information on using the Installer menu, begins below. For information on the PROCISE Tools utility, refer to the PROCISE Tools help file.
Crestron PSPHD PROCISE™ Surround Sound Processor Audio Setup Use the Audio Setup section of the Installer menu to define the room’s speaker configuration. Main speaker arrangement, center-channel speakers, subwoofers, and speaker impedance can be defined in the Audio Setup menu. Open Audio Setup To open the Audio Setup section of the Installer menu: 1. Open the Installer menu as described on page 30. 2. Turn the selection knob until Audio Setup is displayed and press the selection knob.
PROCISE™ Surround Sound Processor Crestron PSPHD The following speaker arrangements are available: • Left, Right (L,R): Audio separated into left and right channels. LEFT SCREEN RIGHT CENTER SUBS SEATING • Left, Right, Surround Left, Surround Right (L,R,SL,SR): Audio separated into 4 channel surround sound. For use in a 5.x surround setup.
Crestron PSPHD PROCISE™ Surround Sound Processor • Left, Right, Surround Left, Surround Right, Back Left, Back Right (L,R,SL,SR,SBL,SBR): Audio separated into 6 channel surround sound. For use in a 7.x surround setup. LEFT SURRND LEFT SCREEN RIGHT CENTER SUBS SEATING SURRND RIGHT SURRND BACK LEFT Center Channel Speaker SURRND BACK RIGHT The PSPHD can be configured to use a center channel speaker. To configure the PSPHD to use a center channel speaker: 1.
PROCISE™ Surround Sound Processor 2. Crestron PSPHD Turn the selection knob until Subwoofers is displayed and press the selection knob to open the Subwoofer control. Subwoofer Setup AUDIO SETUP Dual Mono SOURCE 3. MODE SETUP INFO Turn the selection knob to highlight the desired setting and press the selection knob to enable the setting. The following subwoofer arrangements are available: Speaker Impedance • None: No subwoofer is present in the room.
Crestron PSPHD Restore Default Settings PROCISE™ Surround Sound Processor The PSPHD’s audio settings can be restored to their default settings. NOTE: Audio settings set from the front panel and the PROCISE Tools utility are restored to their default settings. To restore the default settings: Back 1. Open the Audio Setup section as described on page 31. 2. Turn the selection knob until Restore Defaults Including Presets is displayed and press the selection knob. 3.
PROCISE™ Surround Sound Processor Pair Crestron Amplifier Crestron PSPHD NOTE: Pairing is for use with Crestron PROAMP amplifiers only. The PSPHD can be paired with a Crestron PROAMP amplifier for control and monitoring of the amplifier.
Crestron PSPHD PROCISE™ Surround Sound Processor NOTE: The PSPHD and the PROAMP amplifer must be set to the same connection type. NOTE: When using the “Network” connection type, the PSPHD and the PROAMP amplifier must be on the same subnet. 7. Press the selection knob to select the “Network” connection type. 8. When prompted, press either of the following buttons on the PROAMP amplifier while the appropriate LEDs blink (about two minutes): • RESET (front panel).
PROCISE™ Surround Sound Processor Crestron PSPHD NOTE: If you change the position of the NETWORK/DIRECT switch again on the PROAMP-7X400, you must then power cycle the device in order for the new setting to take effect. 4. On the PSPHD, open the Network Setup section as described on page 35. 5. Turn the selection knob until “Pair Crestron Amplifier” is displayed. Press the selection knob to open the Amplifier Pairing Control.
Crestron PSPHD PROCISE™ Surround Sound Processor 2. Turn the selection knob until the PSPHD’s IP address is displayed. Press the selection knob to open the IP Address control. The first octet of the IP address will be enclosed in brackets. IP Address Control NETWORK SETUP IP Address 032. 159. [172] SOURCE MODE SETUP 122 INFO 3. Turn the selection knob to display the desired number. 4. Press the selection knob to move the cursor to the next octet. 5.
PROCISE™ Surround Sound Processor 2. Crestron PSPHD Turn the selection knob until the default router’s IP address is displayed. To change the IP address, press the selection knob to open the Default Router control. The first octet of the default router’s IP address will be enclosed in brackets. Default Router Control NETWORK SETUP [173] Default Router 030. 161. SOURCE DHCP MODE SETUP 001 INFO 3. Turn the selection knob to display the desired number. 4.
Crestron PSPHD PROCISE™ Surround Sound Processor WINS Mode Control NETWORK SETUP WINS On SOURCE 3. Hostname MODE Off SETUP INFO Turn the selection knob to highlight the desired setting and press the selection knob to enable the setting and return to the Network Setup section. The PSPHD can be recognized by its hostname in a networked environment. To view and set the hostname: 1. Open the Network Setup section as described on page 35. 2. Turn the selection knob until the hostname is displayed.
PROCISE™ Surround Sound Processor 2. Crestron PSPHD Turn the selection knob until the domain name is displayed. To change the domain name, press the selection knob to open the Domain Name control. Domain Name Control NETWORK SETUP corporate.crestron.com MAC Address Back Del Ins SOURCE MODE < > SETUP INFO 3. Select letters (upper and lower-case), numbers, or other characters by turning the selection knob until the desired letter, number, or other character is displayed on the VFD.
Crestron PSPHD PROCISE™ Surround Sound Processor Control Setup CONTROL SETUP FRONT PANEL IS UNLOCKED SOURCE Front Panel Lock/Unlock MODE SETUP INFO The PSPHD’s front panel can be locked to prevent access to the PSPHD’s controls. To lock and/or unlock the front panel: 1. Open the Control Setup section as described on page 42. 2. Turn the selection knob until the PSPHD’s front panel status is displayed. Press the selection knob to open the Front Panel control.
PROCISE™ Surround Sound Processor 3. Crestron PSPHD Turn the selection knob to highlight the desired setting and press the selection knob to enable the setting and return to the Control Setup section. For more information on assigning Net IDs, refer to “Identity Code” on page 24. IP ID An IP ID for control system communication over TCP/IP can be assigned from the PSPHD’s front panel. To assign an IP ID: 1. Open the Control Setup section as described on page 42. 2.
Crestron PSPHD PROCISE™ Surround Sound Processor • IP Address: a. Turn the selection knob to highlight IP Address and press the selection knob. The first octet of the control system’s IP address will be enclosed in brackets. Enter Control System IP Address CONTROL SETUP Control System IP Address [172] 032. 159. 122 SOURCE • MODE SETUP INFO b. Turn the selection knob to display the desired number. c. Press the selection knob to move the cursor to the next octet. d.
PROCISE™ Surround Sound Processor d. Back Crestron PSPHD After the new name has been entered, press the selection knob to save the name and return to the Control Setup section. At any point in the Control Setup section, you can return to the Installer menu: 1. Turn the selection knob until Back is displayed. 2. Press the selection knob to return to the Installer menu. About Use the About section of the Installer menu to view information about PSPHD’s operating firmware.
Crestron PSPHD PROCISE™ Surround Sound Processor Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at www.crestron.com/support. First-time users will need to establish a user account.
PROCISE™ Surround Sound Processor Crestron PSPHD Locating the PSPHD (Cresnet) in the Device Library • Ethernet: Drag the PSPHD from the Ethernet Control Modules | Ethernet Audio Modules folder of the Device Library and drop it in the System Views. Locating the PSPHD (Ethernet) in the Device Library 2. The system tree of the control system displays the device in the appropriate slot(s) with a default Net ID or IP ID as shown in the following illustration.
Crestron PSPHD PROCISE™ Surround Sound Processor 4. If necessary, double click a device to open the “Device Settings” window and change the Net ID or IP ID, as shown in the following figures. “Device Settings: Crestron PSPHD (Cresnet)” Window “Device Settings: Crestron HD-MD8X1/2 (Ethernet)” Window 5. Program Manager The ID code specified in the SIMPL Windows program must match the Net ID or IP ID of each unit. Refer to “Identity Code” on page 24.
PROCISE™ Surround Sound Processor Crestron PSPHD Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device).
Crestron PSPHD PROCISE™ Surround Sound Processor window in the section marked Ethernet however, communications must be established in order to see this information in the “System Info” window. 2. TCP/IP icon); Display the PSPHD’s “System Info” window (click the communications are confirmed when the device information is displayed. Ethernet Communication PC Running Crestron Toolbox Ethernet PSPHD The PSPHD connects to PC via Ethernet: 1. Establish indirect or USB communication between PSPHD and PC.
PROCISE™ Surround Sound Processor Crestron PSPHD Program Checks Actions that can be performed on the PSPHD vary depending on whether it is connected via Cresnet or Ethernet. Cresnet Connections For Cresnet connections, using Crestron Toolbox, display the network device tree (Tools | Network Device Tree) to show all network devices connected to the control system. Right-click on the PSPHD to display actions that can be performed on the PSPHD.
Crestron PSPHD PROCISE™ Surround Sound Processor Operation Turn on the PSPHD To turn on the PSPHD, press STANDBY, SOURCE, MODE, SETUP, INFO, HOME, METER, SPECTRUM, or LEVEL. NOTE: Until Audyssey calibration has been performed, the PSPHD front panel will show a message every few seconds indicating that the system should be calibrated. Standby To place the PSPHD in the Standby mode press STANDBY. The display and outputs will be turned off and the STANDBY LED will light.
PROCISE™ Surround Sound Processor Crestron PSPHD Surround Sound Decoding Mode Selection Surround sound Decoding modes can be applied to an incoming audio signal. To select a Decoding mode: 1. Press the MODE button. 2. Turn the selection knob until the desired Decoding mode is displayed. 3. Press the selection knob to confirm the Decoding mode. NOTE: Some signals are not compatible with all Decoding modes. 4. Press HOME to return to the home display.
Crestron PSPHD PROCISE™ Surround Sound Processor 2. Press the selection knob. Compression Control SETUP Compression Off SOURCE Audyssey Dynamic EQ ® AUDYSSEY Dyn Vol MODE Dolby/DTS DRC SETUP INFO 3. Turn the selection knob to highlight the desired setting. 4. Press the selection knob to confirm the selection. 5. Press HOME to return to the home display. Audyssey Dynamic EQ can be applied to the incoming signal.
PROCISE™ Surround Sound Processor 3. Crestron PSPHD Press the selection knob to display the Audyssey Dynamic EQ control. Audyssey Dynamic EQ Control SETUP AUDYSSEY Dynamic EQ SOURCE Audyssey MultEQ ® On Off MODE SETUP INFO 4. Turn the selection knob to highlight the desired setting. 5. Press the selection knob to confirm the selection. 6. Press HOME to return to the home display. Audyssey MultEQ can be applied to the incoming signal.
Crestron PSPHD PROCISE™ Surround Sound Processor 3. Press the selection knob to display the Audyssey MultEQ control. Audyssey MultEQ Control SETUP AUDYSSEY MultEQ SOURCE Dolby TrueHD Auto Compression On Off MODE SETUP INFO 4. Turn the selection knob to highlight the desired setting. 5. Press the selection knob to confirm the selection. 6. Press HOME to return to the home display. Dolby TrueHD Auto Compression can be applied to an incoming signal encoded in Dolby TrueHD.
PROCISE™ Surround Sound Processor 3. Crestron PSPHD Press the selection knob to display the Dolby TrueHD Auto Compression control. Dolby TrueHD Auto Compression Control SETUP Dolby TrueHD Auto Compression SOURCE Bass Level On Off MODE SETUP INFO 4. Turn the selection knob to highlight the desired setting. 5. Press the selection knob to confirm the selection. 6. Press HOME to return to the home display. The bass level can be adjusted with the PSPHD front panel. To adjust the bass level: 1.
Crestron PSPHD PROCISE™ Surround Sound Processor 6. Treble Level Press HOME to return to the home display. The treble level can be adjusted with the PSPHD front panel. To adjust the treble level: 1. Press the SETUP button to display the first Setup option. 2. Turn the selection knob to display Treble. Treble Setting SETUP Treble 0.0 dB SOURCE 3. MODE SETUP INFO Press the selection knob to display the Treble control. Treble Control SETUP Treble 0.0 dB SOURCE MODE SETUP INFO 4.
PROCISE™ Surround Sound Processor Crestron PSPHD NOTE: The VU meter receives calibration settings from the speaker impedance value that was set on page 34. To display the VU meter: 1. Press METER. Meters for the left and right channels will be displayed. 2. To view the VU meters for other channels, turn the selection knob. 3. Press HOME to return to the home display. Spectrum Analyzer The PSPHD can display a spectrum analyzer for each channel. To display the spectrum analyzer: 1. Press SPECTRUM.
Crestron PSPHD PROCISE™ Surround Sound Processor Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. PSPHD Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION PSPHD does not function. PSPHD is not receiving power. Use the provided power cord. Verify connection. Sound is not heard. PSPHD is muted. Turn off mute function.
PROCISE™ Surround Sound Processor Crestron PSPHD Cable Length Equation 40,000 L< RxP Where: L = Length of run (or chain) in feet R = 6 Ohms (Crestron Certified Wire: 18 AWG (0.75 MM 2 )) or 1.6 Ohms (Cresnet HP: 12 AWG (4 MM 2 )) P = Cresnet power usage of entire run (or chain) Make sure the cable length value is less than the value calculated on the right side of the equation.
Crestron PSPHD PROCISE™ Surround Sound Processor Future Updates As Crestron improves functions, adds new features and extends the capabilities of the PSPHD, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance.
PROCISE™ Surround Sound Processor Crestron PSPHD Appendix: Audyssey Laboratories, Inc. Established in 2002, Audyssey Laboratories, Inc. is the industry leader in researchbased sound equalization solutions for professional and consumer audio. Audyssey MultEQ XT is a room equalization solution that calibrates any audio system so that it can achieve optimum performance for every listener in a large listening area.
Crestron PSPHD PROCISE™ Surround Sound Processor Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
PROCISE™ Surround Sound Processor Crestron PSPHD Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. MultEQ XT is a trademark of Audyssey Laboratories. Dolby Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. DTS Manufactured under license under U.S.
Crestron PSPHD PROCISE™ Surround Sound Processor This page is intentionally left blank. Operations Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 6837B (2024778) 07.10 Specifications subject to change without notice.