Specifications

3
quickstart guide
PROAMP
(
I
)
-7X400
www.crestron.com
888.273.7876 201.767.3400
©2010 Specifications subject to
change without notice.
QUICKSTART DOC. 6977A (2027299, Sheet 2 of 2) 07.10
PROCISE
™
High-Definition Professional Surround Sound Amplifier
All brand names, product names, and trademarks
are the property of their respective owners.
PRO
AMP(I)-7X40
0
For details, refer to the latest version of the PROAMP(I)-7X400
Operations Guide, Doc. 6976.
INSTALLER MENU
Audio Setup
Network Setup
Control Setup
About
Exit Installer Mode
NETWORK SETUP
Pair Crestron Amplifier
AMPLIFIER PAIRING
Crestron Amplifier Connection
Network Direct
Selection
Knob
HOME
DISPLAY
INSTALLER MENU
Audio Setup
INSTALLER MENU
Audio Setup
PSPHD
To unpair the PROAMP-7X400 and PSPHD, you must clear pairing
information from both devices.
1. To open the INSTALLER MENU on the PSPHD, press and hold the
HOME and DISPLAY buttons simultaneously for approximately five
seconds.
2. Turn the selection knob until Network Setup is displayed, and then press
the selection knob.
3. Turn the selection knob until “Pair Crestron Amplifier” is displayed, and
then press the selection knob to open the Amplifier Pairing Control.
4. When prompted, turn the selection knob to highlight the Clear option, and
then press the selection knob.
5. When prompted by the PSPHD display as to whether you are sure that
you want to clear the pairing information, turn the selection knob to Yes,
and then press the selection knob.
The PSPHD automatically reboots. After the PSPHD reboots, it is
unpaired.
6. To unpair the PROAMP-7X400, press and hold the RESET button on the
front panel while you power cycle the device. The LEDs on the front panel
blink, indicating that the PROAMP-7X400 is unpaired.
Unpairing
6
To test that the PROAMP-7X400 and the PSPHD are paired, press the
DISPLAY button on the PSPHD. Observe that the brightness of the
PROAMP-7X400 front panel display tracks the brightness of the PSPHD
front panel display. The tracking of the brightness indicates that the
devices are paired.
Testing the Pairing Operation
5
To pair the PROAMP-7X400 with the PSPHD use a “direct” connection:
1. Using the NETWORK/DIRECT switch on the rear of the PROAMP-7X400,
set the connection type to DIRECT.
2. Power on the PROAMP-7X400 and the PSPHD.
3. Using the INSTALLER MENU on the PSPHD, pair the PROAMP-7X400
with the PSPHD:
a. To open the INSTALLER MENU, press and hold the HOME and
DISPLAY buttons simultaneously for approximately five seconds.
b. Turn the selection knob until Network Setup is displayed, and then
press the selection knob.
c. Turn the selection knob until “Pair Crestron Amplifier” is displayed, and
then press the selection knob to open the Amplifier Pairing Control.
d. Turn the selection knob to highlight Direct as the connection type
between the PSPHD and the PROAMP-7X400.
e. Press the selection knob to select the Direct connection type.
For additional information about the PSPHD, refer to the latest version of the
PSPHD Operations Guide (Doc. 6837).
NOTE: The PSPHD and the PROAMP-7X400 must be set to the same
connection type.
NOTE: If you change the position of the NETWORK/DIRECT switch again
on the PROAMP-7X400, you must power cycle the device in order for the
new setting to take effect.
Pairing with a “Direct” Connection
4B
The PSPHD automatically reboots. After the PSPHD reboots, the
PROAMP-7X400 and the PSPHD are paired.