CRESTRON Contents Relay Controller: SP-RY 1 Description 1 1 1 2 3 3 4 5 6 6 6 6 7 7 7 8 8 8 Functional Description Physical Description Specifications Setup SP-RY with SmartPresenter™ SP-RY with SmarTouch™ ST-CP SP-RY with CNMSX Programming SmartPresenter™ SP-1 SmarTouch™ ST-CP CNMSX Problem Solving Troubleshooting Further Inquiries Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty Operations Guide - DOC.
CRESTRON Relay Controller: SP-RY Description Functional Description The SP-RY is a relay controller that allows easy control of devices needing low voltage contact closures. The relays can be programmed using momentary, latching, toggle and more through the Crestron software. The controller can be used with the SmartPresenter, SmarTouch ST-CP, and CNMSX systems. NOTE: The SP-RY provides four relays. Each set of two shares a common ground.
CRESTRON Specifications Dimensions: Length Width Height 4.850" (123.19 mm) 1.324" (33.63 mm) 1.052" (26.72 mm) 6.2 oz. (176 g) Device Cable: Length Conductors 3' (91 cm) (6) 22AWG Serial Data Cable¹: Connector Type Length 3.5 mm, Straight, Stereo 3' (91.44 cm) Weight: Serial Data Cable²: Crestron p/n CNSP-112 12v DC Power Supply*: Crestron p/n PW-1205 (USA and Canada) Input 120V 60Hz 18W Output 12vDC 0.5A Crestron p/n PWI-1210 (International) Input 230V 50Hz 110mA Output 12V---1.
CRESTRON Setup SP-RY with SmartPresenter™ Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-RY. Connect the other end of the cable to one of the outputs on the SP-1. The device cable should be connected to the appropriate devices. To locate the Q-Code for the Relay Controller, refer to the latest revision of the SmartPresenter – Quick Guide (DOC. 5742). NOTE: An external power supply is not necessary when using the SP-RY with the SmartPresenter system.
CRESTRON SP-RY with SmarTouch™ ST-CP Connect the 3.5 mm, Serial Data Cable (supplied) to the input port on the SP-RY. Connect the other end of the cable to one of the outputs on the ST-CP. The cable should be connected to the appropriate control device. To program the ST-CP for the Relay Controller, refer to the SmarTouch STS Wizard included with VisionTools Pro™ or the latest revision of Crestron's SIMPL™ Windows® programming software (v 1.20.
CRESTRON SP-RY with CNMSX The SP-RY can be used with a variety of Crestron systems, including the CNMSX. When used with a CNMSX there are additional hardware requirements. • A specially designed Serial Data Cable is required (p/n CNSP-112). • An external power supply is required. Refer to "Specifications" on page 2 for part number and input/output voltage specifications. Connect the stereo plug of the CNSP-112 into the input port of the SP-RY.
CRESTRON Programming SmartPresenter™ SP-1 The SmartPresenter is field programmable and does not require a PC. Refer to the latest revision of the SmartPresenter – Quick Guide (DOC. 5742). SmartPresenter software is available, however, it is only necessary for changing drivers, cloning SP-1 machines, and updating firmware. SmarTouch™ ST-CP The SmarTouch systems are easily programmed using the SmarTouch STS Wizard. In several easy steps a SmarTouch system can be programmed and up-loaded.
CRESTRON Problem Solving Troubleshooting TROUBLE SP-RY not functioning. POSSIBLE CAUSE(S) SmartPresenter Q-Code incorrect SmarTouch ST-CP /CMMSX Incorrect Driver Selected No 12v power supply CORRECTIVE ACTION Verify that the correct Q-Code for the device has been assigned. Select the correct driver from the Crestron database. 12v power supply must be used (see "Specifications" on page 2).
CRESTRON Return and Warranty Policies Merchandise Returns / Repair Service 1. 2. 3. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address.
