CRESTRON Contents Hand-Held Wireless Transmitter 1 Description .......................................................................................................................... 1 Functional Description ........................................................................................... 1 Physical Description............................................................................................... 1 Leading Specifications ...............................................................
CRESTRON Hand-Held Wireless Transmitter Description Functional Description The ST-4T and ST-8T are hand-held radio-frequency (RF) transmitters. The units are designed to operate with the SmarTouch STS via the ST-CP, control processor. The hand-held transmitter is available with four (ST-4T) or eight (ST-8T) button controls. Depression of any fixed button on the button panel initiates a RF signal transmission to the ST-CP.
CRESTRON ST-4T Physical Views SIDE VIEW FRONT VIEW ST-8T Physical Views SIDE VIEW 2 • Hand-Held Wireless Transmitter FRONT VIEW Operations Guide - DOC.
CRESTRON A standard nine-volt battery is included with all units. Access to the battery is permitted after the battery cover, located on the underside of the unit, is removed. A sensor (photo transistor) used to program an identity code is also located in the battery compartment, as shown below. Battery Compartment (Rear View) Leading Specifications The table below provides a summary of leading specifications for the hand-held transmitters.
CRESTRON NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CRESTRON Crestron Performance Viewport Dialog Box From the Options menu in the dialog box, select Set Transmitter ID to open the “Set Transmitter ID” dialog box. Enter a two-digit hexadecimal number ranging from 03 to FE. Click OK to confirm. Set Transmitter ID Dialog Box Programming STS VisionTools for Windows contains sample projects, ST4T.prj and ST8T.prj, that can be used when programming the hand-held wireless transmitters.
CRESTRON Copy Project Dialog Box NOTE: The illustration above shows what the “Copy Project” dialog box would look like if the programmer were to copy the ST-4T sample project with the new project name, remote-1. As illustrated, a "From" and "To" field is provided. If the desired project is not present in the field, directly key in the path name (at the From: box) or select Browse to display the "Open" dialog box and scroll through directories to establish the correct path of a desired source for the copy.
CRESTRON Open Page of ST4T.PRJ DO NOT reassign join numbers in the new project, since they represent the physical location of actual buttons on the transmitter. Use STS/VTW to assign device commands when customizing the SmarTouch system. To access the functional properties of the button, simply right-click on the object and select Function from the pop-up menu. The "Function" dialog box appears. Function Dialog Box Shown for Button with Join Number 2 Operations Guide - DOC.
CRESTRON One possible programming technique is to assign the same command to both join numbers on the large button so that the entire button has a single command. Otherwise, assign a unique command to each join number so that the button has dual functionality. For example, commands such as VOLUME UP and VOLUME DOWN are usually assigned to the separate button halves; operation of each half is achieved by pressing down on that side of the button.
CRESTRON Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a CRESTRON technical support representative. ST-4T/-8T Troubleshooting TROUBLE LED on unit does not illuminate. Intermittent response during transmission. No response from SmarTouch system. POSSIBLE CAUSE(S) No battery in unit or battery is dead. Unit is in sleep mode. CORRECTIVE ACTION Install new battery.
CRESTRON Further Inquiries If after reviewing this Operations Guide for the hand-held transmitter, you can not locate specific information, please take advantage of CRESTRON's award winning technical support team in your area. Dial one of the following numbers. 10 • Hand-Held Wireless Transmitter • In the US, call (888) CRESTRON [(888) 273-7876] - the call is toll free or (201) 767-3400. • In Europe, call +32.15.730.974. • In Asia, call +852.2341.2016. • In Latin America, call +525.574.15.90.
