Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Operations Guide
This document was prepared and written by the Technical Documentation department at: Important Safety Instructions • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Regulatory Compliance As of the date of manufacture, the SWAMP-24X8 and SWAMPI-24X8 have been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Contents Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 Introduction The SWAMP-24X8 is the centerpiece of a fully-scalable audio distribution system that delivers high-output audiophile sound quality to every room with significantly reduced cabling, low power consumption, advanced DSP, and integrator-friendly setup. The Sonnex™ Multiroom Audio System facilitates massive systems with up to 74 zones and over 30,000 Watts of power.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Features and Functions (Continued) • • • • • Remote fault monitoring Seamless Crestron system integration Heavy duty detachable terminal blocks ease speaker wire termination Low power consumption, cool-running operation 4-space 19” rack-mountable The Sonnex system topology minimizes speaker wiring distances by allowing expansion units to be placed central to the rooms they serve, routing 24 stereo channels of uncompressed digital audio and control t
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Bonus Zones Sonnex leaves no zone behind, providing two additional S/PDIF digital outputs for sharing stereo sources with centralized audio processors and AV receivers. Sonnex Digital Audio Transport Among the many features that set Sonnex apart from all other multiroom systems is the Sonnex Audio Transport. On the rear of the SWAMP-24X8 are eight Sonnex Link ports, enabling the connection of up to eight SWAMPE-4 or SWAMPE-8 expanders1.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 • Dynamic Range Control — When you listen to music or watch TV, you want to enjoy it at a volume level that lets you hear everything clearly — which can be difficult to do if there are competing background noises or someone resting in the next room. Not only that, but the level from one song to the next, and between TV programs and commercials, can fluctuate wildly.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Passive Subwoofer Support Sonnex lets you enjoy extended low frequency performance in any room, providing high-performance biamplification capability to support any passive in-wall, in-floor, or freestanding subwoofer. Configuring Sonnex to handle a 2.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Applications The following diagram shows a SWAMP-24X8 in a multi-zone application. SWAMP-24X8 in a Multi-Zone Application 6 • Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 Operations & Installation Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Specifications Specifications for the SWAMP(I)-24X8 are listed in the following table.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 SWAMP(I)-24X8 Specifications (Continued) SPECIFICATION DETAILS Audio (continued) Balance Control3 Left/right adjustable 3 Selectable Mono Summing Power Limiting 3 Sonnex Speaker Protect (SSP) output limiting; Configurable 40 to 140 Watts @ 8 Ohms 40 to 240 Watts @ 4 Ohms 40 to 400 Watts @ 8 Ohms bridged Tone Profiles3 Flat, Classical, Jazz, Pop, Rock, Spoken Word EQ Modes3 5-band graphic or 5-band parametric EQ 3 GEQ Center Frequencies 6
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System SWAMP(I)-24X8 Specifications (Continued) SPECIFICATION DETAILS Enclosure Chassis Metal with black finish, vented sides, variable-speed fan-cooled Front Panel Extruded aluminum, black finish with polycarbonate label overlay Mounting Freestanding or 4U 19-inch rack-mountable (feet and rack ears included) Dimensions Height 7.51 in (191 mm) with feet 6.97 in (178 mm) without feet Width 19.00 in (483 mm) with ears 17.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Physical Description This section provides information on the connections, controls and indicators available on your SWAMP-24X8. SWAMP-24X8 Physical View (Front) SWAMP-24X8 Physical View (Rear) 10 • Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 Operations & Installation Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System SWAMP-24X8 Overall Dimensions (Top) 18.47 in (470 mm) 17.29 in (439 mm) 19.00 in (483 mm) Operations Guide – DOC.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 SWAMP-24X8 Overall Dimensions (Front & Back) 1 2 3 4 5 6 6.97 in (178 mm) 7.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 3 K, J (Up, Down) (2) push buttons, scroll up or down through menu and adjust menu parameters 4 ENTER (1) push button, executes highlighted menu item or value 5 On/Off (1) Rocker switch, turns power amplifier on and off and resets the unit 6 SOURCE (1-24) Buttons and LEDs (24) Push buttons and green LEDs, select input source for routing and adjustment 1 7
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS DESCRIPTION 12 FUSE The SWAMP-24X8 requires a T15AH (1/4” x 1-1/4”, 250V, 15A, time-lag, high-rupture 2 rated) fuse ; The SWAMPI-24X8 requires a T8AH (5 mm x 20 mm, 250V, 8A, time-lag, high-rupture rated) fuse 2 13 120V~50/60Hz MAX 12A3 (1) IEC C14 male chassis plug, main power input; Mates with removable power cord (included with SWAMP-24X8) 14 DIGITAL OUT (1
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Connectors, Controls & Indicators (Continued) # CONNECTORS1, CONTROLS & INDICATORS 20 GROUND 21 SPEAKER OUTPUTS (1-8) DESCRIPTION (1) 6-32 screw, chassis ground lug (16) 2-pin 7.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Setup Network Wiring When wiring the Cresnet network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators).
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System • Each network device must have a unique Net ID. The Net ID can be set from the SWAMP-24X8’s front panel or with Crestron Toolbox. For more details, refer to “Set the Cresnet ID” on page 38 or the Crestron Toolbox help file. IP ID The IP ID is set from the SWAMP-24X8’s front panel or within the SWAMP-24X8’s IP table using Crestron Toolbox. For more details, refer to “Set the IP ID” which starts on page 39 or the Crestron Toolbox help file.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 2. There are screws that secure each side of the SWAMP-24X8 top cover. Using a #1 or #2 Phillips screwdriver, remove the four screws closest to the front panel from one side of the unit. Refer to the diagram following step 4 for a detailed view. 3. Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 2. 4.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Hardware Hookup Connect the Device Make the necessary connections as called out in the illustration that follows this paragraph. Refer to “Network Wiring” on page 16 for additional information. Apply power after all connections have been made.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Typical Balanced/Unbalanced Inputs Balanced Input L Unbalanced Input R +-G+- L R +-G+- Shield Source L Source R + Source L + Jumpers Shield + Source R + Shield CH Device Connections Devices with a RJ-45 CH output such as the CEN-IDOCV can be connected to the balanced inputs on the SWAMP-24X8 as shown in the following table.
Crestron SWAMP(I)-24X8 Bridge Speaker Outputs (Optional) Sonnex™ Multiroom Audio System The speaker outputs on the SWAMP-24X8 can be bridged to deliver higher power to a speaker. The left channel on an individual output can be bridged with the right channel on the same output. Refer to the following diagram when bridging outputs. Bridging Outputs + + L R The possible bridging combinations are: Zone 1 + Zone 2, Zone 3 + Zone 4, Zone 5 + Zone 6, Zone 7 + Zone 8.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Wiring Diagram: Passive Subwoofer Using Bridged Output BUSSED + - + - SUB - LEFT + BRIDGED RIGHT STEREO PAIR ROOM 1. Connect the speakers and subwoofer as shown in one of the previous diagrams. 2. The SWAMP-24X8 can use a 2nd or 4th order crossover filter to separate the audio signals between the subwoofer and the left-right stereo pair speakers.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System For more information, refer to “Set Bus Assignment” which starts on page 31, “Bridge Outputs” which starts on page 32, or the Sonnex Tools help file. 4. Use Sonnex Tools or the SWAMP-24X8’s “Installer Mode” menu to set the subwoofer output to Mono. For more information, refer to “Set Mono/Stereo” which starts on page 29 or the Sonnex Tools help file. 5. Trim the subwoofer using an SPL meter, the pink noise files (satellite pink noise.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 SWAMP-24X8 to SWAMPE Connection (SWAMPE-8 shown) NOTE: The maximum cable length between a SWAMP-24X8 and a peripheral is 200 feet (61 meters). Fuse Replacement If the SWAMP-24X8 does not power up when it is plugged into an AC outlet, the fuse may need to be replaced. The fuse holder is located on the rear panel, above the IEC socket assembly. To replace the fuse: 1. Use a flat head screwdriver to push in the fuse holder. 2.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Configuration After making all hardware connections, the SWAMP-24X8 must be configured for operation. The SWAMP-24X8 can be configured from the SWAMP-24X8’s front panel using the “Installer Mode” menu or from a PC using the Sonnex Tools application in Crestron Toolbox. This document contains instructions for using the "Installer Mode” menu. For information on using Sonnex Tools to configure the SWAMP-24X8, refer to the Sonnex Tools help file.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 3. Press ENTER to select Compensation and display the list of sources. 4. Press the T or ▲ buttons to scroll through the sources until the input source to be adjusted is displayed. 5. Press ENTER to select the input source and display the gain control. Gain Control 6. Press the T or ▲ buttons to display the amount of gain to be applied and press ENTER. The display returns to the list of input sources. 7.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System • Impedance: Specifies the impedance of a speaker connected to a selected zone. • Speaker Protect: Enables or disables the Speaker Protect function. NOTE: As speaker ratings vary greatly across manufacturers, there is no guarantee that Sonnex Speaker Protect protects against speaker damage in all situations. Enter/Exit the “Zone Setup” Menu Set EQ (Equalization) • Crestron DRC: Enables or disables the Crestron Dynamic Range Control function.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Bass Setting Set Treble 4. Press the T or ▲ buttons to display the setting to be applied and press ENTER. 5. Repeat for every zone to be adjusted. 6. Press MENU to return to the “Zone Setup” menu. To adjust a zone’s treble setting: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 27. 2. Press the T or ▲ buttons to display Treble and press ENTER. A list of zones is displayed. 3.
Crestron SWAMP(I)-24X8 Set Balance Sonnex™ Multiroom Audio System To adjust a zone’s balance setting: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 27. 2. Press the T or ▲ buttons to display Balance and press ENTER. A list of zones is displayed. 3. Press the T or ▲ buttons to display the zone to be controlled and press ENTER. The balance setting is displayed. Balance Setting Set Mono/Stereo 4.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Minimum Volume Setting Set Maximum Volume 4. Press the T or ▲ buttons to display the setting to be applied and press ENTER. 5. Repeat for every zone to be adjusted. 6. Press MENU to return to the “Zone Setup” menu. To adjust a zone’s maximum volume setting: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 27. 2. Press the T or ▲ buttons to display Maximum Volume and press ENTER.
Crestron SWAMP(I)-24X8 Set Bus Assignment Sonnex™ Multiroom Audio System To assign a zone to a bus of zones: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 27. 2. Press the T or ▲ buttons to display Bussing and press ENTER. A list of zones is displayed. 3. Press the T or ▲ buttons to display the zone to be controlled and press ENTER. The bus setting is displayed. Bus Setting Set Bus Volume Offset 4.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Bus Display Bridge Outputs 4. Press the T or ▲ buttons to display the other zones contained in the bus. 5. Press ENTER to return to the list of busses. 6. Repeat for every bus to be viewed. 7. Press MENU to return to the “Zone Setup” menu. To bridge outputs together: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 27. 2. Press the T or ▲ buttons to display Bridging and press ENTER.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Wattage Setting 4. Press the T or ▲ buttons to display the speaker’s wattage rating and press ENTER. NOTE: If your speaker rating is not displayed, select the next-lowest rating to avoid damage to the connected speakers. Set Speaker Impedance 5. Repeat for every zone to be configured. 6. Press MENU to return to the “Zone Setup” menu. To specify the impedance of speakers connected to a zone output: 1.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Speaker Protect Setting Set Crestron Dynamic Range Control (DRC) 4. Press the T or ▲ buttons to display the desired setting and press ENTER. 5. Repeat for every zone to be configured. 6. Press MENU to return to the “Zone Setup” menu. To enable/disable DRC for a zone output: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 27. 2. Press the T or ▲ buttons to display Crestron DRC and press ENTER.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Expander Status Select this option to view the status and information about SWAMPE Multiroom Audio Expanders that are connected to the SWAMP-24X8. To view information: 1. Enter the “Installer Mode” menu as described in “Enter the “Installer Mode” Menu” on page 25. 2. Press the T or ▲ buttons to display Expander Status and press ENTER. 3. Press the T or ▲ buttons to display the expander to view and press ENTER. 4.
Sonnex™ Multiroom Audio System Set the IP Address Crestron SWAMP(I)-24X8 The SWAMP-24X8 can use TCP/IP for communication between a control system and a SWAMP-24X8. The IP address can be manually set or obtained from a DHCP server. For information on enabling DHCP to obtain an IP address, refer to “Enable/Disable DHCP” on page 37. To view or manually set an IP address: 1. Enter the “Network Setup” menu as described above. 2. Press the T or ▲ buttons to display IP Address and press ENTER.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Default Router Enable/Disable DHCP 3. Press the T or ▲ buttons to set the first octet of the default router. 4. Press the soft key under the next octet (or press ENTER to move to the next octet) to select it for editing. 5. Repeat steps 3 and 4 for each octet. 6. To save the default router and return to the “Network Setup” menu, move the cursor to the right-most octet and press ENTER.
Sonnex™ Multiroom Audio System Display Hostname Crestron SWAMP(I)-24X8 To display the hostname: 1. Enter the “Network Setup” menu as described on page 35. 2. Press the T or ▲ buttons to display Hostname and press ENTER. The hostname is displayed. 3. Press ENTER to return to the previous screen. NOTE: The hostname can be changed with Crestron Toolbox. Display Domain Name To display the domain name: 1. Enter the “Network Setup” menu as described on page 35. 2.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Cresnet ID Setting 3. Set the IP ID Press the T or ▲ buttons to display the desired setting and press ENTER. The display returns to the previous screen. If the SWAMP-24X8 is to talk to a control system over TCP/IP, the IP ID must be set. To set the IP ID using the front panel: 1. Enter the “Control Setup” menu as described on page 38. 2. Press the T or ▲ buttons to display IP ID and press ENTER. The IP ID setting is displayed. IP ID Setting 3.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 About Select this option to view information about the SWAMP-24X8. To view information about the SWAMP-24X8: 1. Enter the “Installer Mode” menu as described in “Enter the “Installer Mode” Menu” on page 25. 2. Press the T or ▲ buttons to display About and press ENTER. 3. Press the T or ▲ buttons to display information about the SWAMP-24X8. 4. Press ENTER to return to the “Installer Mode” menu.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron Web site. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at www.crestron.com/support. First-time users need to establish a user account.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Locating the SWAMP-24X8 (Cresnet) in the Device Library b. To incorporate the SWAMP-24X8 (Ethernet) into the system, drag the drag the SWAMP-24X8 from the Ethernet Control Modules | Ethernet Audio Modules folder of the Device Library and drop it in the System Views.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System NOTE: If using Cresnet for communications between the SWAMP-24x8 and a control system, only one SWAMPE Multiroom Audio Expander or one S-EXT1-S Sonnex Link Over Fiber Extender (connected to a SWAMPE Multiroom Audio Expander) can be connected. 2. If additional SWAMP-24X8 devices are to be added, repeat step 1 for each device. Each SWAMP-24X8 is assigned a different Net ID number as it is added. 3.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device).
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System “System Info” window in the section marked Ethernet however, communications must be established in order to see this information in the “System Info” window. 2. TCP/IP Display the SWAMP-24X8’s “System Info” window (click the icon); communications are confirmed when the device information is displayed. Ethernet Communication PC Running Crestron Toolbox LAN SWAMP-24X8 The SWAMP-24X8 connects to PC via Ethernet: 1.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Program Checks Actions that can be performed on the SWAMP-24X8 vary depending on whether it is connected via Cresnet or Ethernet. Cresnet Connections For Cresnet connections, using Crestron Toolbox, display the network device tree (Tools | Network Device Tree View) to show all network devices connected to the control system. Right-click on the SWAMP-24X8 to display actions that can be performed on the SWAMP-24X8.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Operation The SWAMP-24X8 can be controlled from the front panel or the Sonnex Tool in Crestron Toolbox. NOTE: For more information, refer to the Crestron Toolbox help file. When operated from the front panel, the SWAMP-24X8 operates in either the Zone mode or Source mode. Use the “Main” menu to select Zone mode or Source mode. To display the “Main” menu, press MENU until Main Menu appears.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. SWAMP-24X8 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Device does not function. Device is not communicating with the network. Use Crestron Toolbox to poll the network. Verify network connection to the device.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System chain. If the unit is run from a Crestron system power supply network port, the Cresnet power usage of that unit is the Cresnet power usage of the entire run. The wire gauge and the Cresnet power usage of the run should be used in the following equation to calculate the cable length value on the equation’s left side. Cable Length Equation 40,000 L< RxP Where: L = Length of run (or chain) in feet R = 6 Ohms (Crestron Certified Wire: 18 AWG (0.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 Future Updates As Crestron improves functions, adds new features and extends the capabilities of the SWAMP-24X8, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron Web site periodically for manual update availability and its relevance.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Sonnex™ Multiroom Audio System Crestron SWAMP(I)-24X8 This page is intentionally left blank. 52 • Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 Operations & Installation Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System This page is intentionally left blank. Operations Guide – DOC.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 7049B (2028550) 01.12 Specifications subject to change without notice.
