Crestron SWAMP(I)-24X8 ® Sonnex Multiroom Audio System Operations Guide
Important Safety Instructions • • • • • • • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Regulatory Compliance These products conform to UL 60065; certified to CSA C22.2 No. 60065.03. As of the date of manufacture, the SWAMP-24X8 and SWAMPI-24X8 have been tested and found to comply with specifications for CE marking. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Contents Sonnex Multiroom Audio System: SWAMP(I)-24X8 1 Introduction ............................................................................................................................... 1 Features and Functions ................................................................................................ 1 Applications.................................................................................................................
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Sonnex Multiroom Audio System: SWAMP(I)-24X8 Introduction The SWAMP-24X8 is the centerpiece of a fully scalable audio distribution system that delivers high-output audiophile sound quality to every room with significantly reduced cabling, low power consumption, advanced DSP, and integrator-friendly setup.
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 Features and Functions (Continued) • • • • • • • • • • • • • • • • • • • • • Additional line-level, S/PDIF, and “CH” CAT5 balanced outputs available1 70/100 Volt “constant-voltage” output options available Output bussing enables linked operation of multiple adjacent zones Bridgeable outputs provide extra power for pools and other large areas Sonnex Link provides a 1-wire, plug-and-play interface to eight SWAMPE expanders up to 200 feet (61 meters) awa
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Integrated Audiophile Amplifier The amplifiers in the SWAMP-24X8 use a custom hybrid amplifier design that achieves the warmth and neutrality of a fine Class AB amplifier with all of the efficiency benefits of modern Class D. Each of the SWAMP-24X8’s 16 channels (configured as eight stereo zones) delivers 140 watts into 8 ohms, or 240 watts into 4 ohms.
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 Sonnex Digital Audio Transport Among the many features that set Sonnex apart from all other multiroom systems is the Sonnex Audio Transport. On the rear of the SWAMP-24X8 are eight Sonnex Link ports, enabling the connection of up to eight Sonnex Multiroom Audio Expanders (SWAMPE-4 or SWAMPE-8).
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System • Dynamic Range Control (DRC) is a user-selectable feature to help keep everything at a consistent level, whether in a quiet bedroom, a loud swimming pool, or an outdoor patio, facilitating a more cohesive listening experience. • Sonnex Speaker Protect (SSP®) output limiting assures maximum headroom while preventing damage to the amplifier or speakers.
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 Unamplified Outputs For applications requiring line level zone outputs, Crestron offers the SWE-8 Sonnex Multiroom Audio Unamplified Expander (sold separately). Each SWE-8 provides an assortment of analog line level, S/PDIF digital, and Crestron Home (CH) CAT5 balanced audio outputs, offering a solution for routing audio to AV receivers, powered subwoofers, headphone amplifiers, phone systems (for music-on-hold), and other audio equipment.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Applications The following diagram shows a SWAMP-24X8 in a multizone application. SWAMP-24X8 in a Multizone Application Operations Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Specifications Specifications for the SWAMP(I)-24X8 are listed in the following table.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System SWAMP(I)-24X8 Specifications (Continued) SPECIFICATION DETAILS Audio (continued) Power Limiting Tone Profiles EQ Modes 3 Sonnex Speaker Protect (SSP) output limiting; Configurable 40 to 140 watts @ 8 ohms 40 to 240 watts @ 4 ohms 40 to 400 watts @ 8 ohms bridged 3 Flat, Classical, Jazz, Pop, Rock, Spoken Word 3 5-band graphic or 5-band parametric EQ GEQ Center Frequencies GEQ Gain 3 3 EQ, High Pass, Low Pass, Treble Shelf, Bass Shelf, Notch
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System SWAMP(I)-24X8 Specifications (Continued) SPECIFICATION DETAILS Dimensions Height 7.51 in (191 mm) with feet 6.97 in (178 mm) without feet Width 19.00 in (483 mm) with ears 17.29 in (439 mm) without ears Depth 18.47 in (470 mm) Weight 60.0 lb (27.3 kg) Available Models SWAMP-24X8 Sonnex Multiroom Audio System SWAMPI-24X8 Sonnex Multiroom Audio System – International Version Available Accessories 1. 2. 3. 4. 5.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Physical Description This section provides information on the connections, controls, and indicators available on the SWAMP-24X8. SWAMP-24X8 Physical View (Front) SWAMP-24X8 Physical View (Rear) Operations Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System SWAMP-24X8 Overall Dimensions (Top) 18.47 in (470 mm) 17.29 in (439 mm) 19.00 in (483 mm) 12 • Sonnex Multiroom Audio System: SWAMP(I)-24X8 Operations Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System SWAMP-24X8 Overall Dimensions (Front and Back) 1 2 3 4 5 6 6.97 in (178 mm) 7.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Connectors, Controls, and Indicators (Continued) # 1 CONNECTORS, CONTROLS, AND INDICATORS DESCRIPTION 3 Up, Down (2) Push buttons, scroll up or down through menu and adjust menu parameters 4 ENTER (1) Push button, executes highlighted menu item or value 5 On/Off (1) Rocker switch, turns power amplifier on and off and resets the unit 6 SOURCE (1-24) Buttons and LEDs (24) Push buttons and green LEDs, select input source for routing and adj
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Connectors, Controls, and Indicators (Continued) # 1 CONNECTORS, CONTROLS, AND INDICATORS DESCRIPTION 12 FUSE 13 120V~50/60Hz MAX 3 12A (1) IEC 60320 C14, main power inlet; Mates with removable power cord (included) 14 DIGITAL OUT (1-8) (8) 8-wire RJ-45 female; Sonnex expansion link outputs; Green LED indicates link status; Amber LED indicates data communication on the corresponding output; Connect to Sonnex Multiroom Audio 4,5 Expanders (so
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Connectors, Controls, and Indicators (Continued) # 1 CONNECTORS, CONTROLS, AND INDICATORS 19 SETUP (LED and button) 20 GROUND 21 SPEAKER OUTPUTS (1-8) DESCRIPTION (1) Recessed miniature push button and (1) red LED, used for touch-settable ID (TSID) in conjunction with Crestron Toolbox software (1) 6-32 screw, chassis ground lug (16) 2-pin 7.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Setup Network Wiring When wiring the Cresnet network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (www.crestron.com/calculators).
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 When setting the Net ID, consider the following: IP ID • The Net ID of each unit must match an ID code specified in the Crestron Studio™ or SIMPL Windows program. • Each network device must have a unique Net ID. The IP ID is set from the SWAMP-24X8’s front panel or within the SWAMP-24X8’s IP table using Crestron Toolbox. For more details, refer to “Set the IP ID” which starts on page 39 or the Crestron Toolbox help file.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System • Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. • Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Hardware Hookup Connect the Device Make the necessary connections as called out in the illustration that follows this paragraph. Refer to “Network Wiring” and “Sonnex Link Wiring” on page 17 for additional information. Apply power after all connections have been made.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Typical Balanced/Unbalanced Inputs Unbalanced Input Balanced Input L R + - G+ - L R + - G+ - Shield Left Jumpers + Left + Right + + Right CH Device Connections Devices with a RJ-45 CH output such as the CEN-IDOCV can be connected to the balanced inputs on the SWAMP-24X8 as shown in the following table.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Bridge Speaker Outputs (Optional) The speaker outputs on the SWAMP-24X8 can be bridged to deliver higher power to a speaker. The left channel on an individual output can be bridged with the right channel on the same output. Refer to the following diagram when bridging outputs. Bridging Outputs + - + - L R The possible bridging combinations are Zone 1 + Zone 2, Zone 3 + Zone 4, Zone 5 + Zone 6, and Zone 7 + Zone 8.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Wiring Diagram: Passive Subwoofer Using Bridged Output BUSSED LEFT SUB - + - + + BRIDGED - RIGHT STEREO PAIR ROOM 1. Connect the speakers and subwoofer as shown in one of the previous diagrams. 2. The SWAMP-24X8 can use a 2nd or 4th order crossover filter to separate the audio signals between the subwoofer and the left-right stereo pair speakers.
Sonnex Multiroom Audio System 4. Crestron SWAMP(I)-24X8 Use Sonnex Tools or the SWAMP-24X8’s “Installer Mode” menu to set the subwoofer output to Mono. For more information, refer to “Set Mono/Stereo” on page 30 or the Sonnex Tools help file. 5. Trim the subwoofer level using an SPL meter, the pink noise files (satellite pink noise.wav and subwoofer pink noise.wav) found in the Sonnex Tools help file, and Sonnex tools.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System NOTE: If using Cresnet for communications between the SWAMP-24x8 and a control system, only one expander can be connected. NOTE: The maximum cable length between a SWAMP-24X8 and an expander is 200 feet (61 meters). If additional length is needed, the S-EXT1-S can extend the Sonnex link up to 2000 feet (610 meters) over one multimode fiber strand.
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 Configuration After making all hardware connections, the SWAMP-24X8 must be configured for operation. The SWAMP-24X8 can be configured from the SWAMP-24X8’s front panel using the “Installer Mode” menu or from a PC using the Sonnex Tools application in Crestron Toolbox. This document contains instructions for using the "Installer Mode” menu. For information on using Sonnex Tools to configure the SWAMP-24X8, refer to the Sonnex Tools help file.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System 2. Press ENTER to select Source Setup. 3. Press ENTER to select Compensation. 4. Press q or ▲ until the input source to be adjusted is displayed. 5. Press ENTER to select the input source and display the Gain screen. Gain Screen Source 1 Gain 0.0 dB ▲ q 6. Press q or ▲ to display the amount of gain to be applied and press ENTER. The display returns to the list of input sources. 7. Repeat steps 4 through 6 for each input source. 8.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System • Impedance specifies the impedance of a speaker connected to a selected zone. • Speaker Protect enables or disables the Speaker Protect function. NOTE: As speaker ratings vary greatly across manufacturers, there is no guarantee that Sonnex Speaker Protect protects against speaker damage in all situations. Enter/Exit the “Zone Setup” Menu Set EQ (Equalization) • Crestron DRC enables or disables the Crestron Dynamic Range Control function.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Bass Screen Bass Set Treble Zone 1 0.0 dB ▲ q 4. Press q or ▲ to display the bass setting to be applied and press ENTER. 5. Repeat for every zone to be adjusted. 6. Press MENU to return to the “Zone Setup” menu. To adjust a zone’s treble setting, perform the following procedure: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 28. 2. Press q or ▲ to display Treble and press ENTER.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System 2. Press q or ▲ to display Balance and press ENTER. A list of zones is displayed. 3. Press q or ▲ to display the zone to be controlled and press ENTER. The Balance screen is displayed. Balance Screen Zone 1 Balance Set Mono/Stereo 0 ▲ q 4. Press q or ▲ to display the balance setting to be applied and press ENTER. 5. Repeat for every zone to be adjusted. 6. Press MENU to return to the “Zone Setup” menu.
Crestron SWAMP(I)-24X8 Set Maximum Volume Sonnex Multiroom Audio System 5. Repeat for every zone to be adjusted. 6. Press MENU to return to the “Zone Setup” menu. To adjust a zone’s maximum volume setting, perform the following procedure: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 28. 2. Press q or ▲ to display Maximum Volume and press ENTER. A list of zones is displayed. 3. Press q or ▲ to display the zone to be controlled and press ENTER.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Bus Screen Bus Set Bus Volume Offset Zone 1 5 ▲ q 4. Press q or ▲ to display the bus to which the zone is to be assigned and press ENTER. 5. Repeat for every zone to be assigned. 6. Press MENU to return to the “Zone Setup” menu. To adjust a zone’s bus volume offset setting, perform the following procedure: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 28. 2.
Crestron SWAMP(I)-24X8 Bridge Outputs Sonnex Multiroom Audio System To bridge outputs together, perform the following procedure: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 28. 2. Press q or ▲ to display Bridging and press ENTER. A list of zones is displayed. 3. Press q or ▲ to display the zone to be configured and press ENTER. The Bridging screen is displayed.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Set Speaker Impedance To specify the impedance of speakers connected to a zone output, perform the following procedure: 1. Enter the “Zone Setup” menu as described in “Enter/Exit the “Zone Setup” Menu” on page 28. 2. Press q or ▲ to display Impedance and press ENTER. A list of zones is displayed. 3. Press q or ▲ to display the zone to be configured and press ENTER. The Impedance screen is displayed.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Crestron DRC Screen Zone 1 Crestron DRC Set Global EQ On q 4. Press q or ▲ to display the desired DRC setting and press ENTER. 5. Repeat for every zone to be configured. 6. Press MENU to return to the “Zone Setup” menu. To adjust a global EQ setting, perform the following procedure: NOTE: Adjusting a global EQ setting overrides the individual EQ settings for all zones. 1.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Amplifier Status Select this option to view the settings and operating status of each of the SWAMP-24X8 amplifiers as well as the amplifiers of connected expanders. To view information about the amplifier, perform the following procedure: 1. Enter the “Installer Mode” menu as described in “Enter the “Installer Mode” Menu” on page 26. 2. Press q or ▲ to display Amplifier Status and press ENTER. The “Amplifier Status” menu is displayed.
Crestron SWAMP(I)-24X8 Set the Subnet Mask Sonnex Multiroom Audio System 3. Press q or ▲ to set the first octet of the IP address. 4. Press the button under the next octet (or press ENTER to move to the next octet) to select it for editing. 5. Repeat steps 3 and 4 for each octet. 6. To save the IP address and return to the “Network Setup” menu, move the cursor to the right-most octet and press ENTER. To cancel the operation and return to the previous screen, press MENU.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System 6. Enable/Disable DHCP To save the default router and return to the “Network Setup” menu, move the cursor to the right-most octet and press ENTER. To cancel the operation and return to the previous screen, press MENU. The SWAMP-24X8 can obtain an IP address, subnet mask, and default router information from a DHCP server. To enable or disable DHCP, perform the following procedure: 1. Enter the “Network Setup” menu as described on page 36. 2.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System 2. Press q or ▲ to display Domain Name and press ENTER. The domain name is displayed. 3. Press ENTER to return to the previous screen. NOTE: The domain name can be changed with Crestron Toolbox. Control Setup Select this option to configure and view the SWAMP-24X8 control system settings. Enter/Exit the “Control Setup” Menu Lock Front Panel To enter the “Control Setup” menu, perform the following procedure: 1.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System 2. Press q or ▲ to display IP ID and press ENTER. The “IP ID” screen is displayed. “IP ID” Screen IP ID 03 ▲ q 3. Set the Control System IP Address Press q or ▲ to display the desired setting and press ENTER. The display returns to the previous screen. If the SWAMP-24X8 is to communicate with a control system over TCP/IP, the control system’s IP address must be set.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device).
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System USB NOTE: May be required for initial setup of Ethernet parameters. USB Communication USB SWAMP-24X8 PC Running Crestron Toolbox The COMPUTER port on the SWAMP-24X8 connects to the USB port on the PC via the included Type A to Type B USB cable: TCP/IP 1. Click Tools | System Info. 2. Click the 3. For Connection Type, select USB.
Crestron SWAMP(I)-24X8 Firmware Sonnex Multiroom Audio System Check the Crestron website to find the latest firmware. (New users must register to obtain access to certain areas of the site, including the FTP site.) Upgrade SWAMP-24X8 firmware via Crestron Toolbox. 1. Establish communication with the SWAMP-24X8 as described in “Establishing Communication” which starts on page 41. 2.
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 Operation The SWAMP-24X8 can be controlled from the front panel or the Sonnex Tool in Crestron Toolbox. NOTE: For information on Crestron Toolbox, refer to the Crestron Toolbox help file. Power To turn on the SWAMP-24X8, move the POWER switch to . To turn off the SWAMP-24X8, move the POWER switch to . Operating Modes When operated from the front panel, the SWAMP-24X8 operates in either Zone mode or Source mode.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System 5. Press MENU to return to the “Main Menu”. Volume Control To raise the volume in the selected zone(s), turn the VOLUME knob clockwise. To lower the volume in the selected zone(s), turn the VOLUME knob counterclockwise. Operations Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. SWAMP-24X8 Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Device does not function. Device is not communicating with the network. Use Crestron Toolbox to poll the network. Verify network connection to the device.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System chained must be added together to determine the Cresnet power usage of the entire chain. If the unit is run from a Crestron system power supply network port, the Cresnet power usage of that unit is the Cresnet power usage of the entire run. The wire gauge and the Cresnet power usage of the run should be used in the following equation to calculate the cable length value on the equation’s left side.
Sonnex Multiroom Audio System Crestron SWAMP(I)-24X8 updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an “Addendum” in the Download column. 48 • Sonnex Multiroom Audio System: SWAMP(I)-24X8 Operations Guide – DOC.
Crestron SWAMP(I)-24X8 Sonnex Multiroom Audio System Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from Crestron. To obtain warranty service for Crestron products, contact an authorized Crestron dealer. Only authorized Crestron dealers may contact the factory and request an RMA (Return Merchandise Authorization) number.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 7049D (2028550) 04.14 Specifications subject to change without notice.