Crestron TPS-1700 Isys® Wired 5.
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2004 Crestron Electronics, Inc.
Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel Contents Isys® Wired 5.7 Inch Tabletop Touchpanel: TPS-1700 1 Introduction ............................................................................................................................... 1 Functions and Features ................................................................................................ 1 Specifications ...........................................................................................................
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel: TPS-1700 Introduction Functions and Features The TPS-1700 is a compact Crestron Isys® wired 5.7-inch tabletop touchpanel that provides user interface to a Crestron® remote control system (Cresnet® system). The unit provides dynamic on-screen feedback for real-time confirmation of commands. Functional Summary • • • • • • • • • • 5.7 in (14.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Specifications The table below provides a summary of specifications for the TPS-1700. Specifications of the TPS-1700 Touchpanel SPECIFICATION DETAILS Power Requirements 10 Watts (0.40 Amp @ 24 VDC) Default Net ID 03 Default Standby Timeout 10 minutes Signal Join Maximums 4K (digital), 4K (analog), 999 (serial) Control System Update Files 1 2 2-Series Control System Version C2-2004.CUZ or later CEN/CN-TVAV Version 5.13.12V.
Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel NOTE: Crestron software and any files on the website are for Authorized Crestron dealers and Crestron Authorized Independent Programmers (CAIP) only. New users may be required to register to obtain access to certain areas of the site (including the FTP site). Physical Description The touch-sensitive viewing screen is located on the front of the TPS-1700. The electronic hardware is housed in a black and silver molded plastic enclosure.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Physical Views of TPS-1700 (continued) Four rubber feet on the underside of the unit are for stability and to prevent slippage on flat surfaces. Industry Compliance As of the date of manufacture, this unit has been tested and found to comply with specifications for CE marking and standards per EMC and Radio Communications Compliance Labeling (N11785). 4 • Isys® Wired 5.7 Inch Tabletop Touchpanel: TPS-1700 Operations Guide - DOC.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 NOTE: These devices comply with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) these devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesired operation.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 throughout the network. Also, for networks with lengthy cable runs, it may be desirable to add a hub/repeater after only 20 network devices. Identity Code Every equipment and user interface within the Cresnet system requires a unique Cresnet identity code (Net ID). These codes are two-digit hexadecimal numbers from 03 to FE. Refer to “Select Interface” on page 7 for instructions on setting the unit’s Net ID.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Setup Menu SETUP MENU To obtain the SETUP MENU, shown to the left, press the Setup button from the MAIN MENU. The SETUP MENU offers a series of buttons, which open additional menus and screens that are detailed in subsequent paragraphs. After setup parameters have been set, select the Return button to return to the MAIN MENU. NOTE: For convenience, the current CRESNET ID setting is displayed in the lower left corner.
Isys® Wired 5.7 Inch Tabletop Touchpanel STARTUP PREFERENCE Crestron TPS-1700 Startup Preference NOTE: This feature applies only to units with the optional bezel and “hard” pushbuttons installed (refer to “Appendix: Installation of Optional Pushbuttons”). You can use these buttons to access any frequently used commands. For detailed information, refer to “Optional Pushbuttons” on page 16.
Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel Hardware Hookup CAUTION: Do not apply excessive pressure to the touchscreen display during handling. Doing so can crack the screen and damage the touchpanel. The TPS-1700 touchpanel has rubber pads on the underside of its base so that it can rest on a horizontal surface. The only connection necessary is made to the 6-pin RJ-11 connector mounted in the bottom of the unit base.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website (www.crestron.com). To post your own question or view questions you have submitted to Crestron’s True Blue Support, log in at http://www.crestron.com/accounts/login.asp. First-time users will need to establish a user account.
Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel Programming with Crestron System Builder The easiest method of programming, but does not offer as much flexibility as SIMPL Windows. Crestron System Builder offers automatic programming for such residential and commercial applications as audio distribution, home theater, video conferencing, and lighting.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 C2Net-Device Slot in Configuration Manager To incorporate a TPS-1700 into the system, drag the TPS-1700 from the Touchpanels | Touchpanels (Cresnet) folder of the Device Library and drop it in System Views. The PRO2 system tree displays the touchpanel in Slot 9, with a default Net ID of 03 as shown in the following illustration.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 TPS-1700 Symbol in Programming Manager Programming Manager is where programmers “program” a Crestron control system by assigning signals to symbols. The following graphic shows the TPS-1700 symbol in the SIMPL Windows’ Programming Manager. Detail View of the TPS-1700 in SIMPL Windows’ Programming Manager Signal Types Signals interconnect the various devices and logic symbols that comprise a SIMPL program.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Analog Signals Unlike digital signals, analog signals can vary continuously in value, in the same manner as a parameter such as volume, temperature, or pressure. Analog signals contain 16 bits of information, which means that this type of signal can have values ranging from 0 to 65535 (216-1).
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Serial Input Signal Descriptions INPUT DESCRIPTION text-o1 through text-o999 Notifies panel of text string (1 – 999). Also called indirect text. Serial Output Signal Descriptions OUTPUT DESCRIPTION text-i1 through text-i127 For remapping of system reserved joins (1 – 127). Device Extenders Device extenders provide additional logic and functionality to a device.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 VT Pro-e touchpanel files and SIMPL Windows files that illustrate the highperformance capabilities of multi-mode objects. Optional Pushbuttons Pushbutton Layout and Join Number Assignment If the optional ten “hard” pushbuttons are installed, you can use these buttons to access any frequently used commands (refer to “Appendix: Installation of Optional Pushbuttons”).
Isys® Wired 5.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Uploading and Upgrading Assuming a PC is properly connected to the entire system, Crestron programming software allows the programmer to upload programs and projects to the system and touchpanel after their development. However, there are times when the files for the program and projects are compiled and not uploaded. Instead, compiled files may be distributed from programmers to installers, from Crestron to dealers, etc.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Typical Connection Diagram when Uploading Files 1. Open the Crestron Viewport. Either launch the stand-alone version of Viewport, or start SIMPL Windows or VT Pro-e, and from the menu bar, select Tools | Viewport. 2. From the Viewport menu, select Setup | Communications settings (alternatively, press Alt+D) to open the “Port Settings” window. Refer to the figures below and on the next page. Setup | Communications Settings Command 3.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Settings” window are selected as shown after this step. Click the OK button to save the settings and close the window. “Port Settings” Window 4. To verify communication, select Diagnostics | Establish Communications (Find Rack). This should display a window that gives the COM port and baud rate. If communication cannot be established, refer to the “Troubleshooting Communications” section in the respective Operations Guide for the control system.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 File Transfer | Send Program Command 3. The “Send Program” window appears, as shown after this step. Click Browse, locate the compiled file (.spz) and click Open. This will display the program's header information and enable one or both of the What to Send check boxes. If the program does not contain any SIMPL+ modules, only the SIMPL Program check box will be enabled.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Uploading a VT Pro-e Project The TPS-1700 touchpanel source file has the extension .vtp. A compiled VT Pro-e file has the extension .vtz. The VT Pro-e file can be uploaded to the touchpanel using VT Pro-e or via the Crestron Viewport. Upload via VT Pro-e 1. Start VT Pro-e. 2. Select File | Open | Project to view the “Open” window, navigate to the VT Pro-e file (.vtp), and click Open. 3. Select File | Upload Project.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 “Touch Panel Transfer” Window 4. Click Browse. The “Open” window appears as shown below. “Open” Window 5. Select the VT Pro-e (vtz) file and click Open. The transfer will complete automatically. Firmware Upgrade A firmware upgrade file has the extension .csf. To take advantage of all the TPS-1700 touchpanel features, it is important that the unit contains the latest firmware available.
Isys® Wired 5.7 Inch Tabletop Touchpanel 2. Crestron TPS-1700 As shown after this step, select File Transfer | Update Touchpanel Firmware from the Viewport menu. File Transfer | Update Touchpanel Firmware Command 3. As shown after this step, select the Net ID of the TPS-1700 touchpanel and then click OK. The “Open” window appears (refer to the subsequent graphic). “Select Network ID” Window “Open” Window 4. Browse to the .csf file and click Open to begin the transfer. 24 • Isys® Wired 5.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPS-1700 Troubleshooting POSSIBLE CAUSE(S) TROUBLE Touchpanel does not function. Project can not be uploaded to touchpanel. CORRECTIVE ACTION No power to the touchpanel.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 TPS-1700 Troubleshooting (continued) POSSIBLE CAUSE(S) TROUBLE CORRECTIVE ACTION If there are no memory problems, decompressed graphics decrease the drawing time of panel pages. Verify that panel NET ID matches the NET ID set in the program. Eliminate any duplicate NET ID settings. Touchpanel display is Standby timeout has Touch screen to reactivate. dark. elapsed. Touchpanel exhibits slow operation.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Appendix: Installation of Optional Pushbuttons The TPS-1700 is supplied with ten optional pushbutton switches, blank buttons, and a bezel to accommodate the switches. As a further option, custom engraved black or silver buttons (1700C-BTNB or 1700C-BTNS) can be designed and purchased via the Crestron Engraver software. Version 2.3.0.0 or later is available from the Downloads | Software Updates section of the Crestron website (www.crestron.com).
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Software License Agreement This License Agreement (“Agreement”) is a legal contract between you (either an individual or a single business entity) and Crestron Electronics, Inc. (“Crestron”) for software referenced in this guide, which includes computer software and, as applicable, associated media, printed materials, and “online” or electronic documentation (the “Software”).
Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully document and certify that use of any and all Software at the time of the request is in conformity with Your valid licenses from Crestron of its authorized agent.
Isys® Wired 5.7 Inch Tabletop Touchpanel Crestron TPS-1700 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron TPS-1700 Isys® Wired 5.7 Inch Tabletop Touchpanel This page intentionally left blank. Operations Guide - DOC. 6223A Isys® Wired 5.
Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888.CRESTRON Fax: 201.767.7576 www.crestron.com Operations Guide – DOC. 6223A 10.04 Specifications subject to change without notice.
