Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Operations & Installation Guide
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2002 Crestron Electronics, Inc.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Contents Video Card for TPS/Lectern Panel: TPS-VIDL-1/TPS-VIDL-2 1 Introduction......................................................................................1 Features and Functions ..........................................................1 Specifications.........................................................................2 Physical Description ..............................................................4 Industry Compliance.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Video Card for TPS/Lectern Panel: TPS-VIDL-1/TPS-VIDL-2 Introduction Features and Functions The TPS-VIDL-1 and TPS-VIDL-2 video cards are designed for Crestron’s Isys TPS-4500L, TPS-5000L, and TPS-6000L lectern/wall mounted touchpanels as well as the TPS-TPI Touchpanel Interface. Each card contains a video digitizer that allows video signals to be displayed on a touchpanel.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 The TPS-VIDL-1 can automatically detect composite or S-video. The TPS-VIDL-2 adds input for a second composite video source (on the TPS-VIDL-2, Composite/S-Video can be auto-detected only when input signal 2 is not used). When using the TPS-VIDL-2 for receiving two video sources, the “Comp/Y” connection will be used for Composite Video Source 1 while the chroma (C) connection will be used for Composite Video Source 2.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Specifications of the TPS-VIDL-1/VIDL-2 (continued) SPECIFICATION Dimensions and Weight DETAILS Height: 1.16 in (2.95 cm) Width: 2.63 in (6.68 cm) Depth: 6.50 in (16.51 cm) Weight: 1.60 oz (0.05 kg) 1. The latest versions can be obtained from the Downloads | Software Updates section of the Crestron website (www.crestron.com). Refer to NOTE after last footnote. 2.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 Connector Specifications of the TPS-VIDL-1/VIDL-2 (continued) PORT TYPE SIGNAL(S) Y+ 6-pin connector, 3.5 mm Y- 6-pin connector, 3.5 mm YS 6-pin connector, 3.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel TPS-VIDL-1/VIDL-2 Side View 0.73 in (1.85 cm) 1.16 in (2.95 cm) TPS-VIDL-1/VIDL-2 Top View 6.50 in (16.51 cm) 2.63 in (6.67 cm) NOTE: The TPS-VIDL-1 circuit board is slightly less populated than the TPS-VIDL-2. Industry Compliance As of the date of manufacture, the card has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785).
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 Installation and Hookup The TPS-VIDL-1 and TPS-VIDL-2 video cards are designed for installation into a dedicated expansion slot on the TPS touchpanel. The only tools required for installation are a #1 Phillips screwdriver and a grounding strap (or grounded workstation). CAUTION: The TPS-VIDL-1, TPS-VIDL-2, and the touchpanel contain electro-static discharge (ESD) sensitive devices.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Remove Touchpanel Rear Cover Screws CAUTION: The connectors of any optional cards that are already installed may have to be aligned slightly to allow the rear cover to be removed. Align the connectors carefully to prevent damage to the card, cover, or touchpanel. 4. Remove the touchpanel rear cover by sliding it towards the bottom of the touchpanel as shown in the following diagram. Operations & Installation Guide - DOC.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 Remove Touchpanel Rear Cover 5. Refer to the following diagram. Using a #1 Phillips screwdriver, loosen and remove the two screws that secure the PCB blank plate and remove the plate. Remove PCB Blank Plate 6. As shown in the diagram after this step, align the pins on the touchpanel interface connector of the TPS-VIDL-1/VIDL-2 with the touchpanel motherboard connector.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Install TPS-VIDL-1/VIDL-2 7. Press the TPS-VIDL-1/VIDL-2 until the connector pins are fully seated. DO NOT force pins into connector. Make sure that the mounted screws align with the mounting posts of the motherboard. 8. Tighten the card mounting screws to finger-tight. CAUTION: The TPS-VIDL-2/VIDL-2 connectors may have to be aligned slightly to fit through the openings in the rear cover.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 Install Touchpanel Rear Cover 10. Refer to the following diagram. Using a #1 Phillips screwdriver, install 10 screws and tighten to 4-inch pounds (0.45 Newton-meters) to secure the cover. Install Touchpanel Rear Cover Screws 11. Refer to the following diagram and make the appropriate S-video or composite video connection(s) as shown. 10 • Video Card for TPS/Lectern Panel: TPS-VIDL-1/TPS-VIDL-2 Operations & Installation Guide - DOC.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Attach Appropriate Video Cables NTSC/PAL INPUT C Y + - S + - S S-VIDEO CHROMINANCE OR COMPOSITE INPUT #2 S-VIDEO LUMINANCE OR COMPOSITE VIDEO INPUT #1 C COMP Y S-VIDEO CHROMINANCE OR COMPOSITE INPUT #2 S-VIDEO LUMINANCE OR COMPOSITE VIDEO INPUT #1 ON TPS-VIDL-2, USE "COMP/Y" FOR SIGNAL 1 AND "C" FOR SIGNAL 2 NOTE: When using the TPS-VIDL-2 for receiving two video sources, the “Comp/Y” connection will be used for Video Source 1 while t
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 can be obtained from the Downloads | Product Manuals section of the Crestron website (www.crestron.com). Setup Configuring the Touchpanel NOTE: Refer to the latest revision of the TPS-4500L, TPS-5000L, or TPS-6000L Operations & Installation Guide (Doc. 5891, 5825, or 5783, respectively) for instructions to access the touchpanel setup screen.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel 2. Select the Video button from the SETUP MENU to set preferences for the video source. If a TPS-VIDL-2 is installed, buttons labeled “Video 1” and “Video 2” will be displayed instead of the single Video button. Select the appropriate “Video” button to set preference for the video source. Video Setup 3.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 4. Select the preferences for the video signals appearance. Refer to the following table for further information. Video Setup Details VIDEO SCREEN BUTTONS Brightness Contrast Saturation Hue Fast Motion / Still Video (toggle) Soft / Sharp (toggle) Default Return DESCRIPTION Use to increase or decrease image brightness. Use to increase or decrease image contrast. Use to increase or decrease image saturation. Use to shift the color balance.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel for Video 1 or “Composite 2” for Video 2) of the Source tab. Refer to the following illustration that shows selection of the video source. Selecting the Video Source NOTE: If the card is not present, the Crestron Viewport displays a warning message during the upload and the video window remains blank. For further information regarding video window objects, refer to the VT Pro-e help file.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 Problem Solving Troubleshooting The table below provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPS-VIDL-1/VIDL-2 Troubleshooting TROUBLE Video window touchpanel has no display. POSSIBLE CAUSE(S) CORRECTIVE ACTION Improper video connection. Incorrect video format selection. Incorrect firmware/software.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel Further Inquiries If after reviewing this Operations & Installations Guide, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: • In the US and Canada, call Crestron’s corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. • In Europe, call Crestron International at +32-15-50-99-50. • In Asia, call Crestron Asia at +852-2341-2016.
Video Card for TPS/Lectern Panel Crestron TPS-VIDL-1/TPS-VIDL-2 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. 2.
Crestron TPS-VIDL-1/TPS-VIDL-2 Video Card for TPS/Lectern Panel This page intentionally left blank Operations & Installation Guide - DOC.
Crestron Electronics, Inc. Operations & Installation Guide - DOC. 6070 15 Volvo Drive Rockleigh, NJ 07647 12.02 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.