PS 210 BRONC Owner's Guide Noise Canceling Bluetooth Stereo Earphones Thank you for purchasing PHIATON® PS 210 BRONC. Please check all of the warnings and notices in the owner's guide before using the product. Please follow the directions, and read the guidelines carefully before use. (Please, keep the owner's guide for your future reference) ~Some functions of PS210 BRONC may not be available when the PS210 BRONC is paired with certain devices.
1. Safety and General Information To prevent danger or property damage, please read these Safety Precautions to ensure that you are using the product properly. Please ensure that you understand and follow these precautions. 1) Use the included USB charge cable. 2) For best comfort and performance, use the appropriately-sized ear tips included with the device. 3) Lower the volume before listening to music or audio to prevent eardrum damage caused by a sudden loud sound.
14) Remove the ear tips from the earphone, wash them with warm water, dry completely and check for any debris before use a clean cloth to clean the Comply™ Foam tips) 15) To purchase additional ear tips, please contact your Authorized PHIATON® Dealer. 16) Please be careful if using the product while driving a vehicle or walking, as the alarm or warning sounds cannot be heard. 17) Product contains batteries. Please dispose of these safely and according te local regulations.
2. Components and Features NC Microphone Packaging Components Noise Canceling Bluetooth Stereo Earphones Jog Switch USB charging cable Ear tips (XS, Comply™ Foam Tips Answer/End Button Extension 2.5@ plug to 3.50 plug) Reset Bunion Neck Strap 2.
3. Wearing Earphones 1) On the earphones, L indicates Left and R indicates Right. (For best performance, it is recommended to wear ear tips that fit your ears.) 2) Use the clip or neck strap for your convenience.
3) When the battery has been drained, you can continue using the earphones by connecting the extension cable to the connector on the bottom of the device. (Noise Canceling and Bluetooth features will NOT operate without battery power) # The earphones can also be used with the extension cable even when the battery has not been drained. In this case, the Noise Canceling feature is available.
4) How to use the Comply™ Foam Tips (@ Place the bottom side of a foam tip to the end of a wave guide. @ Press the foam tip until it reaches the middle of a wave guide. 3 Apply pressure on the foam tip to minimize its size. @ Insert it carefully into the ear. ® The foam tip will gradually expand for about 10 seconds, blocking external noise. [Figure 6] How to use the Comply™ Seam Tips # You can purchase additional foam tips at www.complyfeam.
4. Charging 3 As the battery may be exhausted when you purchase the device, please charge the device before its first use. 1) Open the USB cover of the device, and connect it to a USB cable. 2) Connect the USB cable to a computer (a laptop) or a USB adapter (rating: SV/500mA) and start charging the device. The device is equipped with a built-in battery. The battery will charge when the USB cable is connected.
5. Power ON/OFF and ‘Waiting for Connection Mode’ 1) Push toward [ (D] and hold the power & Lock button for 2 seconds to turn the power on. [figure 5 Note] 2) Push toward [(D] and hold the power & Lock button for 3 seconds to turn the power off. [figure 6 Note] 3) If the device does not change to ‘Pairing mode’ with POWER ON, iris in “Waiting for Connection Mode’. 4) “Waiting for Connection Mode’ lasts about 5 min. If the device is not paired within 5 minutes, it automatically powers itself off.
[Table 2] Front Indicator (LED) Status per the Power ON/OFF Action Front Indicator (LED) Signal Tone Power ON LED Indicator flashes blue once for 1 sec. You will hear the words ‘Power On’ from the earphones. Power OFF LED Indicator flashes Red 5 times. You will hear the words “Power Off from the earphones. Waiting for Connection 12 LED Indicator flashes blue twice in every 6 sec. No Signal tone.
6. Pairing with Bluetooth devices 1) Activate Bluetooth on the ‘Bluetooth device’ you want to connect with the PS 210 BRONC. (If you don’t know how to do this, refer to the manual of the "Bluetooth device’) # A ‘Bluetooth device’ is an electronic device that offers Bluetooth connectivity. Bluetooth devices’ include many cellphones, tablet PCs, PMs, laptops, etc.
[Table 3] Front indicator (LED) status and Signal Tone for pairing Action Front Indicator (LED) Signal Tone Flashing Blue and You will hear the words “Pairing Mode Red LED Activated’ from the earphones. Pairing Mode Flashing Violet LED You will hear the words ‘Device twice Connected’ from the earphones.
7. How to Use the Noise Canceling Function 1) Noise Canceling is a technology that reduces ambient noise for a better listening experience. 2) Performance of Noise Canceling feature on PS 210 BRONC With Phaeton's unique “Noise Blocker” Technology, the PS 210 BRONC offers a top-of-the-class Noise Canceling experience. It reduces the ambient noises heard on Buses, Airplanes and Subways by more than 95%. The effect of the Noise Canceling feature may vary depending on the environment.
4) Precautions when using the Noise Canceling Feature Be extra-cautious when using while walking or driving. Alarms and other warning signs may not be heard. The Noise Canceling feature is optimized for On-flight, On-Train, On-Bus or other environments with a high level of ambient noise. There is no need to use this feature in quiet environments. Wind may affect the performance of the Noise Canceling feature.
8. Using the Product Listening to Music 3 Before start> Ensure that the PS 210 BRONC is powered on. Ensure that the PS 210 BRONC is properly paired with the ‘Bluetooth device. 1) By pressing the jog switch down, you can start the music on the ‘Bluetooth device' from the PS 210 BRONC [Play]. By pressing the jog switch down while the music is playing, you can pause the music [Pause].
18 [Table 5] Front Indicator (LED) status while Playing Music Action Front Indicator (LED) Playing Music LED Indicator flashes blue once every 6 seconds ting (LED slowly dims in and out). 3) You can control your music from the ‘Bluetooth device’ paired with PS 210 BRONC.
9. Using the While Playing Music 1) Answering while playing music Press the Answer/End Button when you hear an incoming call on the PS 210 BRONC. (Music will be stopped and the call will be answered. Music will resume when call ends) Press the Answer/End Button to hang up the call. 2) Making a call while playing music Press and hold the Answer/End button for 1 second to stop the music and redial the last number you called.
10. Using the Product Telephone Functions 1) Answering Calls Press the Answer/End Button when you hear an incoming call on the PS 210 BRONC. You will be able to talk through the PS 210 BRONC. (Volume adjustment: To control the In-Call volume, push the jog switch in the -’ direction) 2) Ending Calls Press the Answer/End button briefly to hang up calls. 3) Declining Incoming Calls Push the jog switch in the * * direction and hold it for 1 second to decline a call.
6) Call Waiting (Must be supported by phone company and network operator) Press and hold the Answer/End button for 1 second to hold the first call and answer the second call. ~ Repeat to return to the first call, Press the Answer/End Button briefly to hang up the first call and connect to the second incoming call. 7) Voice Dialing (Must be supported by phone) Briefly press the Answer/End Button. 8) Transferring Calls between PS 210 BRONC and the phone.
22 11. Using the Product-Hold Function and Others 1)Putting PS 210 BRONC on Held You can put the PS 210 BRONC on hold by sliding the Power & Hold button toward While on hold, you can still answer incoming calls by pressing the Answer/End Button.
2) Turning Front Indicator (LED) ON and OFF Press and hold the Answer/End Button and Jog Switch for 1 second to turn LED function ON and OFF. [Table 8] Front Indicator (LED) status per Front Indicator Activation On and Off Action Front Indicator (LED) Signal Tone Front Indicator Activate Activating During calls or music playback, you will hear two beeps / from the earphones. While on rest, you will hear the words ‘LED Activated’ from the earphones.
[Table 9] Front Indicator (LED) status to Check Remaining Battery Battery Capacity Front Indicator (L.ED) Signal Tone LED indicator flashes blue You will hear the words ‘Battery is full’ for 1 second. from the earphones. 80% or higher LED indicator flashes violet | You will hear the words 80% ~ 30% for 1 second. ‘Battery is moderate’ from the earphones. LED indicator flashes red for | You will hear the words 30% or lower 1 second. ‘Battery is Low’ from the earphones.
4) Voice Prompt ON and OFF Press the jog switch toward while in pairing mode to turn the voice prompt ON or OFF. (Voice Pro rapt may be limited when ending calls or music playback) [Table 10] Front Indicator (LED) status for Voice Prompt On and Off Action Front Indicator (LED) Signal Tone Voice Prompt Activated No change You will hear the words “Voice Prompt Activated’ from the earphones. Voice Prompt Deactivated No change You will hear the words ‘Voice Prompt Deactivated’ from the earphones.
26 ¥ If voice prompt feature is deactivated, you will hear the following beep patterns to indicate various actions.
12. Specifications 1) PS 210 BRONC Controller Specifications Communication Network : Bluetooth standard Ver.3.0 Output power : Power Class? Discover range : Discover able within 10m Normal Charging time : 3.5 hours Call time © 12 hours (Noise Canceling IFFY 10 hours (Noise Canceling ON) Music play time : 14 hours (Noise Canceling OFF) 11 hours (Noise Canceling ON) Stand-by time : 500 hours (Noise Canceling OFF)/ 50 hours (Noise Canceling ON) Operating Frequency : 2.4GHz (2.402GHz ~ 2.
13. Troubleshooting Cause Action Cannot power on » Please charge the PS 210 BRONC. If it still cannot be powered on after charging, please contact the service center. Cannot charge the PS 210 BIN » Please check the connection between USB cable and PS 210 BIN. * Please confirm that the computer is turned on and connected properly.
Cause Action Poor music sound quality « If PS 210 BRONC is paired as HSP, please change it to AVDP. LED indicator not working * Please check whether the LED is deactivated. (You can activate the LED by pressing and holding the Call Button and jog switch for 1 second) Poor Noise Reduction » Confirm that the Noise Canceling feature is activated. (Check NC Button and NC Indicator (LED)) » Confirm that the ear tips on the earphones are the correct size for your ears.
14. FCC compliance Information FCC ID : V2R-PS210BTNC This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. And (2) this device must accept any interference Received, including interference that may cause undesired operation. Information to the user NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, Pursuant to part 15 of the FCC Rules.
