BonoBuds Hybrid Active Noise Cancelling Earbuds Thank you for purchasing the PHIATON BonoBuds - Please follow the directions and read the guidelines carefully before use. - Please keep the owner’s guide for future reference. - Some functions of the PHIATON BonoBuds may not be available when it is paired with certain devices. - The specifications are subject to change without prior notice for quality improvement. CONTENTS 1. Safety and general information 2. Package Contents 3. Pairing 4. Charging 5.
1. Safety and general information 1) Use a standard USB charging cable (included), with or without a charging adapter. (5V, over 1 A) ※Adapter not included. 2) Lower the volume prior to listening to audio to prevent potential damage to eardrums caused by sudden loud sound. 3) Listening to loud music for extended periods of time may cause hearing damage. 4) Do not store the device in places with a temperature higher than 113 ℉/ 45 ℃. 5) This device is IPX4 sweat and water resistant. It is not waterproof.
2. Package Contents 1) Package Contents - BonoBuds Earbuds - BonoBuds Charging Case - 3 Sizes of Silicon Ear Tips (M Silicone tips come pre-attached.
2) Components & Features Charging Case LED Earbuds LED Type-C Charging 3. Pairing When you take the earbuds out of the case, you can proceed with ‘pairing’. Remove the film on the earbuds and charge for at least 10 minutes before first time use. ① Turn the Bluetooth on of your device. ② When earbuds is taken out of the case, the earbuds are automatically turned on and ready for pairing after 5 seconds.
4. Charging The earbuds begin charging from the moment they are stored in the case. Case supports USB Type C charging 4-1. Charging the Earbuds ① Earbuds start charging when you put them in the case. ② The LED on the earbuds turns on and the earbuds are charging. ※ When the earbuds are fully charged, the ‘Earbuds Charging Status LED’ on the case turns off. 4-2. Charging the Case 1) Using the Charging cable ① Connect the ‘Type-C charging cable’ to the port on the back of the case.
4-3. Checking Battery Level 1) Check the earbuds battery level When the battery level is less than 10%, the earbuds red LED blinks twice every 5 seconds. When the remaining battery power is low, voice guidance is provided every 5 minutes. ‘Battery is low’ 2) Check the case battery level When you open the case, you can check the charge level through the ‘Case Charge Status LED’. ※ A red LED means the earbuds can be charged less than once. ※ The white LED means the earbuds can be charged more than once.
2) Turning off the earbuds When you put the earbuds in the ‘case’, the earbuds automatically turn off. ※ You can turn on/off the earbuds only when there is remaining battery power in the case. 3) Turn on/off earbuds manually. Press and hold the earbuds touch part for 5 seconds to turn on the power and provide voice guidance. ‘Power On’ If you press the touch part again for 5 seconds, the power is turned off and voice guidance is provided. ‘Power Off’ 6.
⑤ When earbuds is taken out of the case, the earbuds are automatically turned on and ready for pairing after 5 seconds. ⑥ After searching for a device in ‘Bluetooth Settings’ of the device to be connected, select ‘PHIATON BonoBuds’ to complete pairing. ⑦ When the earbuds are connected to the device, voice guidance is provided. ‘Device connected’ 7.
8. Call Function If you receive a call while using, tap the earbuds to answer and end the call. 1) Answering a call Tap earbud twice to accept / end a call. 2) Ending a call When the call is over, double-tap the earbuds to end the call. (In the case of a call received while listening to music, the music will automatically pause and will play again when the call ends.) ※ You can also control the music directly from the ‘Bluetooth Device’ ※ Functions may vary depending on the paired Bluetooth device.
10. Ambient mode (Audio Transparency) ① Ambient mode Allowance is a function that allows you to hear ambient sounds without removing the earbuds from your ears while the noise canceling function is in operation. ② If you press and hold the touch part of the right earbud for 2 seconds, the noise canceling function stops and you can listen to external sounds. At this time, you will be guided by voice.
. Product Reset If an unknown problem occurs with the, most issues can be resolved by simply resetting the device. ① With the earbuds in the case, simultaneously press the touch parts of both earbuds for 8 seconds. ※ ⑧ When the white LED of the earbuds lights up twice, the product is in the initialized state. When earbuds is taken out of the case, the earbuds are automatically turned on and ready for pairing after 5 seconds.
. Specifications Communication Network Bluetooth Version 5.2 Bluetooth Profiles A2DP 1.3.2, Audio Codec SBC, AAC Operating Frequencies 2.4GHz(2.402~2.480GHz) Operating Range Within 10m Music Play NC On 6 hrs Standby Time Earbuds : 100hrs / Charging Case : 5000hrs Full Charge Time Earbuds : 1.5hrs / Charging Case : 1.5hrs Earbuds Dimensions (L x W x H) 24 x 23.3 x 27.4mm / 0.95 x 0.92 x 1.08 inch Charging case Dimensions (L x W x H) 70.7 x 38.8 x 32.7mm / 2.79 x 1.53 x 1.
※ Charging case Dimensions (L x W x H) 32.7mm 38.8mm 70.7mm ※ The specifications are subject to change without prior notice for quality improvement.
14. Troubleshooting 1) The power does not turn on: - Make sure the earbud protection film has been removed. - Charge the device for at least 30 minutes. - If the power does not turn on even after charging, contact PHIATON Customer Service. 2) The device does not charge: - Make sure the earbud protection film has been removed. - Check whether the USB charging cable has been properly connected with the device. Check whether the PC power is on and that it has been properly connected.
6) The other party cannot be heard while on a call: - Check if the power of the Bluetooth device you want to connect is on. - Check whether the volume within the connected Bluetooth device is low 7) When noise canceling or ambient mode does not work: - Please check if all earbuds L/R work by putting them in the case and taking them out again. - When wearing one earbud, the noise canceling function does not work.
15. Certification FCC Compliance Information FCC ID: V2R-TN0610 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Compliance Information IC ID: 10488A-TN0610 This device complies with Industry Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules.