REMOTE START & SECURITY PERFECTED RS-X70 INSTALLATION GUIDE Quick Reference - Installation Overview 1 Choose a discreet mounting location for the module and locations for any accessories (siren, sensors, interface module, etc.). Do not mount the module yet (you might anger the install gods). 2 Identify vehicle connection points and plan harness routing from your mounting location. Avoid any moving vehicle parts or parts that generate heat. Also avoid any sharp metal edges.
Table Of Contents Installation Considerations �������������������������������������������������������������������� 3 6 Pin Main Wire Harness ������������������������������������������������������������������������� 3 Red & Red/White Wires - Constant Power (+) Input ����������������������������� 3 Pink Wire - IGNITION/ACC/START (+) Input/Output ����������������������������� 3 Orange Wire - ACCESSORY/IGN/START (+) IN/Out ���������������������������� 4 Violet Wire - Start (+) INPUT/Output ���������������������
Installation Considerations • • • • • • BEFORE STARTING THE INSTALLATION, READ THIS ENTIRE MANUAL TO DETERMINE INSTALLATION REQUIREMENTS VERIFY EACH CIRCUIT WITH A DIGITAL MULTIMETER IDENTIFY REQUIRED CIRCUITS FOR THE VEHICLE TAPE OFF OR REMOVE ANY UNUSED WIRING TO PREVENT POSSIBLE SHORT CIRCUITS ONLY ACTIVATE THE REMOTE START FUNCTION IN A WELL VENTILATED ENVIRONMENT AFFIX THE UNDERHOOD WARNING STICKER AVOID ANY AIRBAG CIRCUITS, USUALLY INDICATED BY A YELLOW SLEEVE OR JACKET AROUND THE WIRING 6
6 Pin Main Wire Harness (cont’d) ORANGE WIRE - ACCESSORY/IGN/START (+) IN/OUT This circuit is designed to power additional IGNITION, ACCESSORY, or START circuits. By default, it functions as an ACCESSORY output & turns on when remote start is activated (slightly earlier than the ignition output), turns off during engine cranking, & turns back on for the remainder of the remote start operation. CONNECTION: Use any IGNITION, ACCESSORY, or secondary START circuit in the vehicle.
14 Pin Secondary Wire Harness (cont’d) BLACK/WHITE WIRE - NEUTRAL SAFETY (-) INPUT REQUIRED. This input is a critical safety circuit which allows remote start operation whenever the gear selector is in park or neutral (automatic transmission), or when the parking brake is applied (manual transmission). Remote start will not operate unless this wire sees chassis ground.
Wiring Overview Diagram 14 PIN HARNESS Remote Start Activation (-) In - WHITE/BLUE Starter Interrupt (-) Out - ORANGE3 Alarm Ign. Control (+) - YELLOW Flashing Light (-) Out - WHITE/BLACK OEM Arm (-) Out - LT. GREEN/RED3 Trunk Release/CH2 (-) Out - RED/WHITE System Ground (-) In - BLACK OEM Disarm (-) Out - LT.
TEMPERATURE SENSOR 4 PIN DOOR LOCK PORT Lock (-) Out - GREEN Constant 12v (+) Out - PIN Unlock (-) Out - BLUE WINDOW-MOUNT ANTENNA MODULE Status Light Valet / Programming Button 3 PIN SAT. RELAY PORT (RED) Start3 (-) Out - GREEN Constant 12v (+) Out - RED Status3 (-) Out - BLUE GREEN INTERFACE MODULE DATA PORT BLACK INTERFACE MODULE DATA PORT VEHICLE LEARN PROCEDURE 1. Connect any interface module(s) to the data port(s) and set for data mode. 2. Turn the ignition key ON (do not start) 3.
14 Pin Secondary Wire Harness (cont’d) MANUAL TRANSMISSION CONNECTION: The Gray wire also serves as a door pin input (must see all doors) which is required to perform the “manual transmission setup procedure” (detailed in the operation guide). Diode isolate the hood input from the door input using two 1 or 2 amp diodes facing the cathodes (stripes) towards the vehicle wires. If the vehicle’s door pin wire is positive, you must invert the signal with a relay.
3 Pin Satellite Relay Port (RED) GREEN WIRE - START (-) PROGRAMMABLE OUTPUT This output provides a 250mA negative pulse when the large VIOLET start wire is active. It can also be programmed for PULSE AFTER START, STATUS, or DOMELIGHT SUPERVISION. See installer programmable feature #5. CONNECTION: If a negative start output is needed, connect this directly to the vehicle’s negative starter circuit. Otherwise, use a relay (or RS-RP module) to convert this to a high current circuit.
Window Mount Antenna Module Be sure to clean the glass before adhering the antenna. Mount it high in the windshield avoiding metal parts of the vehicle . Metal based window tint can decrease performance. Route the harness to the antenna module avoiding sharp objects that could compromise the harness jacket. 3D Motion Sensor Some models are equipped with a motion sensor that provides added protection for remote start by shutting down the engine if motion is detected during the START output.
Vehicle Learn (cont’d) Step 7: OPTIONAL: To enable Manual Transmission Reservation mode, release and set the parking brake. (The BLACK/WHITE wire must be connected to the parking brake.) System should chirp/flash lights 1x. Step 8: TO SAVE SETTINGS: Shut down RS by pressing the BRAKE pedal. This disables VEHICLE LEARN (installer feature #2). TO CANCEL/START OVER: Shut down RS by remote or input wire. Tach Programming The vehicle’s tach signal must be learned for proper operation.
SECURITY CONVENIENCE User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button (Brake 1x) Unlock button (Brake 2x) Trunk button (Brake 3x) Start button (Brake 4x) Lock + Unlock (Brake 5x) 1 Remote Start Run Time 3 min 10 min 15 min 20 min 30 min 2 Flashing Light Confirmations Unlock: ON RS: ON Unlock: ON RS: Flash Unlock: Flash RS: ON Unlock: Flash RS: Flash 3 Confirmation Chirp Volume Low Med-Low Med-High High 4 BROWN Wire: Siren/Pulsed Horn Pulse LOW P
REMOTE START & SECURITY PERFECTED AL-1775-3DB / RS-475-3D OPERATION GUIDE V1.3 Temporary cover. Final cover is in a separate file.
Table Of Contents Controller & Transmitter Overview �������������������������������������������������������������������� 3 The 2-Way Controller ������������������������������������������������������������������������������������ 3 The 1-Way Transmitter ���������������������������������������������������������������������������������� 3 Controller & Transmitter Functions �������������������������������������������������������������������� 3 Other Remote Start Features ����������������������������������������
Controller & Transmitter Overview THE 2-WAY CONTROLLER Controller part number: 1511-03E (w/ 2 CR2025 batteries) LOCK button Call your dealer or visit www.caralarm.com to order replacement transmitters. Controller battery replacement: Remove the small screw from the lower back case, and separate the transmitter halves. Replace the batteries and reassemble the transmitter case.
Controller & Transmitter Functions (cont’d) UNLOCK / DISARM: Press and release the UNLOCK button. • THE SIREN WILL CHIRP TWICE & THE PARKING LIGHTS WILL FLASH TWICE. • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL FLASH THE UNLOCK LED (TWICE FOR CAR 2) AND BEEP TWICE. REMOTE START: Press and release the START button twice within 5 seconds (see user feature #8 to change). x2 • THE PARKING LIGHTS WILL FLASH ONCE AND THE STATUS LIGHT WILL FLASH RAPIDLY.
Controller & Transmitter Functions (cont’d) TRUNK RELEASE / CHANNEL 2: Press the TRUNK button for 3 seconds. • THE SYSTEM WILL UNLOCK/DISARM AND THE TRUNK WILL OPEN (IF EQUIPPED). • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL FLASH THE TRUNK LED (TWICE FOR CAR 2) AND BEEP TWICE. CHANNEL 3: Press and hold the TRUNK & START buttons for 1 seconds. Press and release “P” then TRUNK within 5 seconds. OR 2 1 • YOUR SYSTEM WILL ACTIVATE THE CH. 3 OUTPUT.
Controller & Transmitter Functions (cont’d) CHANNEL 5: Press and hold the UNLOCK & START buttons for 1 seconds. Press and release “P” three times then TRUNK within 5 seconds. OR 2 1 x3 • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 5 OUTPUT. • UPON RECEIVING CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL FLASH THE UNLOCK & START LED’S 5 TIMES. SILENT ARM / DISARM: Press and release the TRUNK button twice in 5 seconds.
Controller & Transmitter Functions (cont’d) PANIC: Press and hold the LOCK or UNLOCK button for 3 seconds. • THE SIREN/HORN WILL SOUND, THE PARKING LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDING WHICH BUTTON IS PRESSED. OR REMOTE VALET: Press LOCK then UNLOCK then TRUNK + START within 5 seconds. 1 • THE SYSTEM WILL ENTER VALET MODE. SEE PAGE 11 FOR MORE INFO ON VALET MODE.
Controller & Transmitter Functions (cont’d) AUXILIARY FUNCTIONS 1-4: The actual operation of these functions will vary from car to car. They are designed to operate extra vehicle functions like automatic sliding doors or motorized hatches. Aux 1-4 are virtual outputs only available on certain vehicles when this system is integrated with the vehicle’s data network. Consult with your installer to find out if any of these functions are available for your vehicle.
Other Remote Start Features (cont’d) LOW VOLTAGE & HIGH/LOW TEMP AUTOMATIC STARTING This feature will automatically start the engine if the vehicle battery drops below 11.5 volts or the interior temperature goes above or below the pre-programmed threshold. Programming The Activation Low Temperature Threshold: • Turn the ignition switch “on”, then “off” (engine not running), and within 5 seconds press the valet switch twice.
Security System Features LAST DOOR ARMING This system can be configured to arm automatically when all the vehicle’s doors are closed (see user feature #9). When this feature is utilized, the siren/horn will chirp once when all of the doors are closed. At that point, it will start a 30 second countdown (indicated by a fast flashing status light). After 30 seconds, the system will arm (and lock the doors if configured to do so).
Using The Valet Button EMERGENCY OVERRIDE If you were to lose or break your controller, you’d need to perform an emergency override to disarm the system and use your vehicle. To do so, use the following steps: STEP 1 - Enter the vehicle (the alarm should sound). STEP 2 - Turn the ignition key to the “ON” position. STEP 3 - Press the valet switch (located in the window-mount antenna) once. NOTE: Enter your SecureCode at this time if programmed via user feature #13 STEP 4 - Turn the ignition key “OFF”.
The Status Light The status light, located in the antenna, indicates the system’s current status. SECURITY SYSTEM STATUS OFF: The alarm is disarmed and not performing any automatic functions. ON: The alarm is in valet mode. FLASHING SLOW: The alarm is armed and monitoring all entry points. FLASHING FAST: One of the automatic arming features is in progress.
Multi-Car Operation The controller can operate up to 2 different systems. When controlling 2 systems, it will receive all status updates on the currently selected vehicle profile and will receive only trigger alerts for the 2nd vehicle. You can switch from one car to the other at anytime. Use the following steps to change vehicles. SELECTING CAR #1 OR CAR #2 Toggle Vehicle: Press “P” then press UNLOCK.
Anti-Carjacking Protection The system is equipped with two separate Anti-Carjacking protection features (ignition, open door, or both). All are programmable, and must be turned on to operate. Once activated, the user has 60 seconds to cancel the Anti-Carjacking protection process (described below). If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren will begin to chirp for 7 seconds to alert the user that the system is about to enter into an alarm condition.
Programming Controllers/Transmitters Standard Programming: Using this method to program additional or replacement transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature. Before you begin, have all transmitters which are to operate the system at hand and make sure the correct vehicle profile (see page 13) is selected on the controller(s). Step 1 Then, turn the ignition “on”. Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times.
User Programmable Features Feature #1 - Remote Start Run Time 3 Minutes (press LOCK to program) 10 Minutes (press UNLOCK to program) 15 Minutes (press TRUNK to program) 20 Minutes (press START to program) 30 Minutes (press LOCK & UNLOCK to program) This sets the maximum amount of time that the remote start will keep the engine running if it is not shut down by other methods.
User Programmable Features (cont’d) Feature #6 - Open Door Bypass of Ignition Locking On (press LOCK to program) Off (press UNLOCK to program) This feature cancels the automatic locking or unlocking of the vehicle’s doors if one of the doors is open when the ignition switch is turned on or off. Feature #7 - Unlock w/ Trunk Release On (press LOCK to program) Off (press UNLOCK to program) “2nd channel” is most commonly used for trunk release, in which case the alarm should also disarm.
User Programmable Features (cont’d) Feature #13 - SecureCode DEFAULT - 1 Press SecureCode is a unique patented feature which allows you to select the number of Valet Switch presses in two stages, instead of “1 press”, which would be required in order to perform an Emergency Override. If any of the three anti-carjacking features are utilized, a customized SecureCode would also be required to turn it off once it is fully activated. SecureCode operation is described on page 11.
Installer Programmable Features This group of Installer Programmable Features are all accessed as a group in the second level of features’ programming.
Installer Programmable Features (cont’d) Feature #5 - Light Relay (B or 3DB) / Sat. Port Green Wire Function (non-B or 3DB) Dome Light Output (press LOCK to program) Start (press UNLOCK to program) Ignition Output (press TRUNK to program) Accessory Output (press START to program) Status (press LOCK & UNLOCK to program) Light Flash (press TRUNK & START to program) This output can be programmed to perform any functions listed above. B or 3DB models utilize a built in relay.
Installer Programmable Features (cont’d) Feature #10 - Turbo Timer Off (press LOCK to program) Run 1 Minute (press UNLOCK to program) Run 2 Minutes (press TRUNK to program) Run 3 Minutes (press START to program) This feature, the operation of which is described on page 8, when turned on configures the system to automatically keep the engine running briefly after the key is turned off. This operation is designed specifically for vehicles with turbocharged engines.
Installer Programmable Features (cont’d) Feature #17 Low Temp Crank Extender 0ms (press LOCK to program) 200ms (press UNLOCK to program) 300ms (press TRUNK to program) 400ms (press START to program) When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the base timing (see installer feature #7). It applies to tachless modes only (installer feature #3).
SECURITY CONVENIENCE User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button (Brake 1x) Unlock button (Brake 2x) Trunk button (Brake 3x) Start button (Brake 4x) Lock + Unlock (Brake 5x) 1 Remote Start Run Time 3 min 10 min 15 min 20 min 30 min 2 Flashing Light Confirmations Unlock: ON RS: ON Unlock: ON RS: Flash Unlock: Flash RS: ON Unlock: Flash RS: Flash 3 Confirmation Chirp Volume Low Med-Low Med-High High 4 BROWN Wire: Siren / Pulsed Horn Pulse LOW
Back Cover Color cover is in a separate file.
4 Button / 1Way Remote Start Systems QUICK START OPERATION GUIDE 1) Find the part # on the back of the remote to identify the battery. 2) Remove the screw from the back of the remote 3) Gently pry the case in halves apart to access & replace the battery. Lock& Arm* Lock Only* Unlock & Disarm* i ~ .i .r 1412 & 1416 CR2032 (1) 1415 CR2016 (2) Security enabled systems will flash the status LED. Ideal for occupied vehicles, RV's, etc.
4 Button / 1Way Remote Start Systems QUICK START OPERATION GUIDE Engine Start/Stop Run Time Extender ··~ x 2 •O, ;ART ··) •O ♦ Activation is programmable (contact installer). Take Over: Turn ignition key 'ON' (not start), press brake pedal The system will restart the internal run timer. START Low Battery & Low/ Hi Temp Auto-Start Auto-start will activate a max of once per 2 hours. See your installer or the full manual for threshold settings.
4 Button / 1Way Remote Start Systems QUICK START OPERATION GUIDE ~ +~~) C START .r +~~) START CH3/AUX1 - Write function in first column* CH4/AUX2 - Write function in first column* CH5/AUX3 - Write function in first column* AUX4 - Write function in first column* *These special functions may not be available on your vehicle. Consult your installer. PROGRAMMING REMOTES TO THE SYSTEM (UP TO 4) BEFORE YOU BEGIN: Have all remotes for the system at hand. 1) Turn the ignition key "ON" (do not start).
4 Button / 1 Way Remote Start Systems QUICK START OPERATION GUIDE Visit www. CarAlarm.
Features Banks Tach Wire Signal Learn BANK 2 - Low Temp Auto Start: ,JQLWLRQ RQ RII SUHVV YDOHW WLPHV FKLUSV /(' À DVKHV REMOTE START & SECURITY PERFECTED Valet 2x Valet 3x 1 Low Temp Auto Start Threshold 0 Deg F 15 Deg F 32 Deg F (login required) Perform Vehicle Learn (US patent #10,151,289) 9HKLFOH /HDUQ LV WKH XOWLPDWH WLPH VDYHU DQG UHPRWH VWDUW FRQ¿ JXUDWLRQ WRRO ,W FRQ¿ JXUHV PRVW install-critical features to match vehicle requirements.
RS-X70 Wire Diagram WHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*) 4 1 A II 6 3 PIN POL.