SP-402 Combo Alarm & Remote Engine Starting System OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of the SP-402 by Crimestopper Security Products Inc. This booklet contains the information necessary for operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. CONTACT INFORMATION: TECHNICAL SUPPORT (800)-998-6880 Monday - Friday 8:00am - 4:30pm Pacific Website: www.crimestopper.com CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 S.
USING THE REMOTE TRANSMITTER VEH 1 = Blue LED VEH 2 = Red LED Remote AUX Outputs Lock / Arm AUX 1 = Trunk + Lock AUX 2 = Trunk + Unlock AUX 3 = Trunk + Start AUX 4 = Lock + Start Unlock / Disarm Trunk Release VEH Vehicle Select Remote Start NOTE: The VEH button can be used to keep remote control from accidentally operating your vehicle.
QUICK CHART BUTTON FUNCTIONS Button Plus Button Functions Button Options Lock Doors & Arm System Press and Hold 2 Seconds for Panic Mode Unlock Doors & Disarm System Button Button Functions Button Options VEH Selects between Vehicle #1 and Vehicle #2 Press and Hold for 2 seconds Press twice for second door unlock VEH Used to Disable Remote Control Press and Hold for 2 seconds Trunk Pop Aux # 1 Press and Release for Trunk Pop Aux #1 Plus Activates Aux #1 thru Data Module Sliding Door Data
OPERATING INSTRUCTIONS - ALARM ARMING / LOCKING Press the Lock Button on the remote control. The System will arm emit one siren chirp, one light flash, and the LED will begin to flash. Power locks will lock (if equipped). Starter disable circuit will turn on. The 2-Way LCD Pager will beep once while displaying a Locking symbol. After a short delay to allow the vehicle and electronics to settle, the system will be completely armed. DISARMING / UNLOCKING Press the Unlock Button on the remote control.
OPERATING INSTRUCTIONS - ALARM ALARM TRIGGERS If there is an intrusion into the vehicle, a hard impact to the body or the ignition is turned on, the alarm will sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 2 minutes and continue to protect the other un-tampered or unopened zones.
OPERATING INSTRUCTIONS - ALARM REMOTE PANIC PROTECTION To sound the alarm in an emergency or to draw attention to your vehicle, press and hold the Lock button for at least 3 seconds until the siren / horn sounds. Press the Unlock button to reset panic mode. The LCD display will flash most of the icons and emit 10 beeps when the Panic Mode is triggered. TRUNK / HATCH POP (Optional, Remote AUX.
OPERATING INSTRUCTIONS - ALARM PRIOR INTRUSION ALERT This system will notify you if the alarm was triggered while you were away. Upon disarming, there will be four additional siren chirps after the two normal disarm chirps. Check your vehicle for any signs of a break in or tampering. Also, see LED Diagnostics (page 17) to determine the cause of the trigger.
REMO REMOTE ENGINE CONTROLTE ENGINE CONTROL REMOTE START & Trunk Release – Button Press Selection (Option # 8) To eliminate the possibility of accidentally opening the trunk or starting the vehicle, there are (3) options for button press selection. This option will allow you to change whether the Remote starter and Trunk release activate by a: 4. Double button press. 5. Single ½ second press. 6. Press and Hold 2 seconds.
REMOTE ENGINE CONTROL UNSUCCESSFUL REMOTE START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank time of up to4 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 4 seconds to help prevent damage to the starter from over cranking.
IDLE DOWN MODE IDLE DOWN MODE (Option # 26 – 10, 20, 30 minutes or Infinity Run) This mode allows the unit to take over operation of your idling, parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time, until you return, or until the remote start button is pressed.
TIMED SELF STARTING MODE TIMED SELF START MODE This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run time. This can be helpful during extremely cold conditions where engine or fluid freeze-up is a concern. !!THE VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA!! TIMED SELF-START MODE – Exiting the Vehicle: 1) Have engine running with the Key, then press the Start button on the transmitter. 2) Within 10 seconds press the valet/program button once.
TURBO TIMER MODE TURBO TIMER MODE (Option # 31) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1, 3 or 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cooldown without the need for expensive turbo timers. The Default = OFF. To Activate Turbo Timer: With the engine running by key, press Remote Start Button with brake pedal depressed.
MANUAL TRANSMISSION MODE MANUAL TRANSMISSION EXIT PROCEDURE (Option #15-1, 15-3 and 15-4) This system features a Manual Transmission Mode. When exiting the vehicle, there is safety check out procedure required for the manual transmission mode to work. There are 3 choices of operation, 1. Option 15-1: With engine running and vehicle in neutral, set parking brake, then press “KEY” Icon on transmitter. The remote starter will turn on and take over operation of the vehicle. 2.
ANTI CARJACK PROTECTION CARJACK PROTECTION (Option 32-1) This optional feature requires installation of a hidden momentary button or an On/Off switch for Carjack protection. Carjack provides protection while driving your vehicle. If a Carjacker opens, any door with the ignition on, the system arms. When the door closes, the parking lights will flash 2 times and the LED will begin to flash rapidly to confirm the beginning of a Carjack countdown.
ALARM TRIGGER DIAGNOSTICS This systems includes disarm diagnostics, through the LED light, that will help in determining what caused the last trigger of the alarm system. This is a valuable tool in determining how the vehicle was tampered with or if there is a false alarm problem, in which case you can make the necessary adjustments to correct the problem.
TRANSCEIVER / REMOTE CONTROL PROGRAMMING Note: All transmitter codes must be learned at time of programming! This system learns up to 4 different transmitter codes. 1. Turn ignition key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 of the first transmitter.
2 VEHICLE OPERATION 2 VEHICLE CONTROL A single Remote Control can control two different vehicles. To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps (Pg. 12) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing remotes. VEH 1 = Blue LED VEH 2 = Red LED VEH To change from vehicle 1 to vehicle 2, press the VEH button on remote for about 2 seconds. The LED on remote will change from Blue to Red.
BATTERY REPLACEMENT To Replace the Battery: The Remote Control uses two CR-2025 Lithium 3 Volt Batteries. Simply remove the Phillips screw located behind key ring (see diagram below). The top cover snaps apart from the back cover. Slide old batteries out and remove plastic cover. Insert the new batteries into plastic cover and slide into place with the (+) end facing up. The plastic cover keeps the batteries from shorting out against the side of metal housing.
2-Way Data Port Most new vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module.
Crimestopper Security Products Inc. 1770 So. Tapo Street Simi Valley, CA 93063 (800) 998-6880 www.crimestopper.com ©2012 Crimestopper Security Products ONLINE TECHNICAL SUPPORT www.crimestopper.