PART LIST Left Top Panel | Right Top Panel | Left Side Panel Right Side Panel Bottom Panel 1PC 1PC 1PC 1PC 1PC Dividing Panel Back Panel Left Door Panel Right Door Panel Fixed Shelf 1PC 1PC 1PC 1PC 1PC Adjustable Shelf Top Rail Leg Bottom Rail PCS 1PC PCS 1PC
HARDWARE LIST Mé6*13 @7*35mm 215*12mm 28*30mm Allen Bolt Hex Nut Cam Bolt Cam Lock Wood Dowel PCS 8 PCS 31 PCS (Extra 2) | 31 PCS (Extra 2) | 26 PCS (Extra 28*5*16mm Screw Handle Round Head Bolt Shelf Holder Screw 10 PCS (Extra 2) PCS PCS 8 PCS 5 PCS (Extra Allen Wrench Spring Hinge | Open End Wrench Metal Wire Safety Strap Kit 1PC 1PC 1PC PCS 1PC ADDITIONAL TOOLS(Not Provided) Note:It is not recommended to use power tools during assembly.
Step 1. Insert cam bolts (part #3) into per-drilled holes of left top panel (part A), left side panel (part C), right side panel (part D), dividing panel (part F) and back panel (part G) by using fillips head screwdriver. NOTE: Do not over tighten cam bolts. Stop tightening once threads on cam bolt are no longer visible.
Step 2. Attach handles (part #7) to left door panel (part H) and right door panel (part |) by using round head bolt (part #8) and fillips head screwdriver. #8 wm) x4 #7,7" x2 Step 3. Attach bottom rail (part N) to bottom panel (part E) by using wood dowels (part #5), screws (part #10) and fillips head screwdriver. Attach legs (part M) to bottom panel (part E) by using Allen bolts (part #1) and Allen wrench (part #11).
Step 4. Attach metal wires (part #14) to bottom panel (part E) by using hex nut (part #2) and open end wrench (part #13). Insert cam bolts (part #3) into per-drilled holes of bottom panel (part E} by using fillips head screwdriver as shown. NOTE: Do not over tighten cam bolts. Stop tightening once threads on cam bolt are no longer visible. Step 5. Attach dividing panel (part F) to back panel (part G) by using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver.
Step 6. Attach fixed shelf (part J) to dividing panel {part F) by using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver as shown. NOTE: Cam locks must rotate full 180°. See pictured insert.
Step 8. Attach top rail (part L) to right side panel (part D) by using cam locks (part #4) and fillips head screwdriver. NOTE: Cam locks must rotate full 180°. See pictured insert. ward adjacent hole ’R(Q U D clockwise to fantasist Step 9. Attach left side panel (part C) to top rail (part L) and left side panel (part C ) by using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver. NOTE: Cam locks must rotate full 180°. See pictured insert.
Step 10. Attach bottom panel (part E) to left side panel (part C), dividing panel (part F), right side panel {part D) and back panel {part G) by using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver. NOTE: Cam locks must rotate full 180°. See pictured insert. Step 11. Carefully turn the unit upright. Insert the cam locks (part #14) into the per-drilled hole on the bottom of the back panel (part G) and lock by using fillips head screwdriver. NOTE: Cam locks must rotate full 180°.
Step 12. Attach left top panel (part A) to left side panel (part C) and back panel (part G) by using wood dowels (part #5), cam locks (part #4) and fillips head screwdriver. NOTE: Cam locks must rotate full 180°. See pictured insert. 72 tum clockwise to fasten Step 13. Attach right top panel (part B) to back panel (part G) by using screws (part #6) and fillips head screwdriver.
Step 14. Insert shelf holders (part #9) into desired position and slide adjustable shelves (part K) into place. #9 cro x8 Step 15. Press the upper door pins on right door panel (part 1) up. Install right door panel (part 1) to inner runner of per-assembled cabinet as shown.
Step 16. Press the upper door pins on left door panel (part H) up. Install left door panel (part H) to outer runner of per-assembled cabinet as shown.
Safety Strap Kit Wall Anchor Washer Short Screw Long Screw Safety Wall Strap 1PC Ax1PC Bx2PCS Cx1PC Dx1PC Expect SAFETY STRAP WALL ASSEMBLY INSTRUCTIONS 1) Insert short screw (part #C) through washer (part #B) and safety wall strap (part #E) and screw it into the top center of back babel (part G). 2) Drill a 11/32" hole where you want to secure your unit. The hole should be at the same height as the hole in the top center of back panel (part wall anchor (part #A) into the hole.