P/N : 48586900E110-R0
LCD TELEVISION INSTRUCTION MANUAL C32HDGB C37HDGB C42HDGB Proper use guarantees product life. Before using the product, be advised that you read this owner’s manual well and try to operate it.
Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk electric shock.
Caution FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications.
IMPORTANT SAFETY INSTRUCTIONS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
IMPORTANT SAFETY INSTRUCTIONS 16. Wall or Ceiling Mounting When mounting the product on a wall or ceiling, be sure to install the product using the designated mounting tool according to the method recommended by the manufacturer. 17. Attachments and Equipment Never add any attachment and/or equipment without approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury. 18.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. In case of an accident, please unplug the unit from the outlet immediately. To reduce the risk of electric shock, do not remove cover or back. No user -serviceable parts inside. Refer to qualified service personnel for repair.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. Please keep the user's manual in a safe place for future reference. Do not put volatile substance-such as benzene, naphtha- near the product since it may cause a change in the product's colour. Do not spill water or drop the remote controller since it may be a cause of malfunctioning.
Table of Contents Installation and Maintenance Antenna Connection Video Connection Camcorder & Video Game Connection DVD Player Connection STB(Set Top Box) Connection PC Connection Cable TV Broadcasting Connection Connect with the Dolby Digital AMP Name of Each Part Basic Guide Parts of the Remote Controller Method To Use Basic Menu To Watch TV Setting Up TV Stations Selection of TV/VIDEO Input Signal Selection of Multimedia Input Signal Application Guide Picture Adjustment Sound Adjustment Features - Close
Supplied Accessories Make sure that the following accessories are provided with the product. PO DIS PL WE R AY MUL TV/ GU VID TIM EDI A EO 3 IDE 2 1 6 5 9 4 EN 8 7 TER FAV 0 CH AC cord PR EV.
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR : Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. Combining adapter 2. Connect the combining adapter to the antenna input at the left side of the TV set. WHEN USING THE COMBINING ADAPTER : You may obtain the combining adapter at your closest Service Center.
Antenna Connection Antenna Connection Such community TV Antenna installation may be found in most of co-op apartments. When a coaxial cable is used : Plug the coaxial cable to the antenna socket on the wall. Antenna socket at the back of the TV set ANT When a feeder cable is used : Plug the coaxial cable to the antenna socket on the wall.
Antenna Connection Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses Single Antenna Connection VHF Antenna REAR OF THE TV SET UHF Antenna ANT Separate Antenna Connection.
Video Connection Connecting with an External Source You may connect S-Video 1(Rear of the TV) or S-Video 2(Side) input to enjoy clearer and brighter picture images. You can make the connection with the AV1 or AV2 input. REAR AND SIDE OF THE TV SET Note : • If your AV device has both Video OUT terminal and S-Video OUT terminal, S-Video connection is recommended for better picture quality. • If S-Video and RCA jack are connected at the same time, the TV set will only detect the S-Video mode.
Camcorder & Video Game Connection Watching the Camcorder Recording or Video Game on TV 1. Prepare the S-video and RCA connector. 2. These connectors connect to Video1/2 or S-Video1/2 like below the picture. 3. Turn on the TV set and camcorder/video game. 4. Select Video1/2 or S-video1/2, using the “TV/VIDEO” of the Remote controller or “TV/VIDEO” button of the TV set.
DVD player connection When connecting with a component cable REAR OF THE TV SET Note : When you connect with the component, please check the color of cable between DVD and TV set. When connecting with a S-VHS cable and RCA cable REAR AND SIDE OF THE TV SET Note : • If your AV device has both Video OUT terminal and S-Video OUT terminal, S-Video connection is recommended for better picture quality. • If S-Video and RCA jack are connected at the same time, the TV set will only detect the S-Video mode.
STB(Set Top Box) Connection When connecting with a HDMI cable REAR OF THE TV SET When connecting with a component cable REAR OF THE TV SET Set Top Box 15
PC Connection When connecting with PC(D-Sub) cable. 1. Adjust PC resolution to available resolution in LCD TV. 2. Connect between PC and TV set using the D-Sub and Audio cable like below the picture. 3. Turn on the PC and TV set. 4. Select PC mode by pressing “MULTIMEDIA” button on the remote control or “TV/VIDEO” button of the TV set. REAR OF THE TV SET When connecting with a HDMI cable. 1. Adjust PC resolution to available resolution in LCD TV. 2.
PC Connection PC CONNECTION NOTES: 1) If there is a [Vertical Frequency] setting menu in the [Screen] Menu of the PC, adjust the frequency to 60Hz. 2) If the PC resolution is too high, it may be hard to read letters. Select a suitable resolution. 3) HDMI input port receives only Digital Signal. 4) Depending on the graphic card when you plug & unplug the HDMI connection, the screen may not display correctly. Restart the computer if this happens. Multi input resolution available in LCD TV.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to either the Component input, Video1 input or Video2 input. REAR OF THE TV SET Antenna Input Connection Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver.
Connect with the Dolby Digital AMP. If you connect the optical output to a Dolby digital AMP, you can listen to better sound.
Name of Each Part Front Panel and Side Buttons on the TV set have the same functions as those of the remote controller. TV/VIDEO 1 MENU 2 VOL 3 CH 4 5 POWER Control Key Buttons. TV/VIDEO Buttons : Each time you press this button, the TV will cycle through: TV Video1(S-Video1) Video2(S-Video2) COMPONENT1 COMPONENT2 HDMI PC MENU Button : Use this button to enter and exit the MENU. VOL Buttons : Use this buttons to change your TV’s volume or to move the cursor in the menu.
Name of Each Part Rear of the TV set REAR OF THE TV SET 21
Parts of the Remote Controller POWER DISPLAY 1 2 GUIDE 3 TV/VIDEO MULTIMEDIA 5 4 6 1 2 3 4 5 6 7 8 9 OK 0 7 PREV.CH 8 CH FAV 11 9 13 MENU VOL VOL MUTE 10 15 16 14 STILL 12 SCREEN SIZE PIP CH CH CAPTION ADD/ ERASE PIP SLEEP PIP CH 18 17 19 SWAP SOURCE POSITION 21 20 23 22 27 24 P.MODE S.MODE 25 MTS S.EFFECT 26 1. DISPLAY: Display the present modes (ATV/DTV, Video1/2, COMP.1/2, HDMI and PC) and signal information.
Parts of the remote controller POWER DISPLAY 1 2 GUIDE 3 TV/VIDEO MULTIMEDIA 5 4 6 1 2 3 4 5 6 7 8 9 OK 0 7 PREV.CH 8 CH FAV 11 9 13 MENU VOL VOL STILL MUTE 10 15 16 14 12 SCREEN SIZE CH CAPTION ADD/ ERASE PIP CH PIP SWAP SOURCE SLEEP PIP CH 18 17 19 POSITION 21 20 23 22 27 24 P.MODE S.MODE 25 MTS S.EFFECT 26 17. ADD/DEL: Use to add or delete channels to/from memory. 18. SLEEP: Sleep Timer setting.
Method To Use Basic Menu Basic Menu - The basic menu appears on the screen if you press the menu button of the remote control. - There are 5 items Picture, Sound, Channel, Features, and Time in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. 1. Press the "MENU" button. • The main menu appears if you press the “MENU” button. 42 81 58 G R 4 N.R Off Color temp Select 2. Press the ” CH ” button.
To Watch TV On/Off, Number, — , Enter, Mute, Display, VOL , CH - Buttons with same name in the main body performs the same function. Press the “POWER” button on TV set or Remote controller. When pressing the Digit Key button • Press the "ENTER" button if using the number button for channel selection. For example, to watch the No.9 channel, Press the number button "9" and the "ENTER" button. If pressing only number “9” button, it takes a longer time to select the channel. • To watch the No.
To Watch TV 1. Press the “POWER” button on TV set or remote controller. • The Stand-by LED lamp turns on in red color. • Press the “POWER” button on the TV set or remote controller. • The Stand By LED lamp on the front panel begins to fliker in blue color and the TV turns on. 2. Press the “ CH ” button. • Select the desired program by pressing the ” CH button or the number buttons. ” Air 26 3. Adjust volume. • Sound reduces by pressing the “ VOL” button. • Sound increases by pressing the “VOL ” button.
Setting Up TV Stations Auto Search to find Channels - All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. 1. Press the “MENU” button to select the Channel menu. • Move the selection bar to the Channel menu with ” CH ” buttons. Picture Antenna Sound Channel Favorite Channel Edit Feature Time 2. Select the “Antenna” • Place the selection bar on Antenna and select Air, Cable with “ VOL ” buttons.
Setting Up TV Stations Fine tune 1. Searching for channel finely • Select a Channel number you want to tune finely with the ” CH ” buttons. • Press the “MENU” button and move to the Channel menu. • Move the selection bar to the Fine tune with ” CH ” buttons. • Press the “CVOLB“ buttons to adjust the fine tuning. Antenna Favorite Channel Edit Adjust Note: • If you are unable to get a good picture or Sound because of a poor broadcasting signal, adjustment of Frequency might improve it.
Setting Up TV Stations Favorite Channel Edit 1. Locate the selection bar on the Favorite Channel Edit. • Move to Favorite Channel Edit in the Channel menu. • Press the “ VOL ” buttons. Antenna Favorite Channel Edit 2. Add the Favorites Channel • Move the selection bar to the Current Channel with ” CH ” buttons. • Select a Channel number you want to add in Favorites Channel List with the “ VOL ” buttons. • Add the Channel with “DISPLAY” button. Analog Air 22 Clear : Move : Exit 3.
Selection of TV/VIDEO Input Signal When watching video, Camcorder, DVD, Cable TV with External Input - When pressing TV/VIDEO button on the remote controller screen changes as follows: TV => AV1(S-Video1) => AV2(S-Video2) => TV 1. Press the “TV/VIDEO” button on the remote controller. • Screen changes as follows whenever pressing the “TV/VIDEO” button.
Selection of Multimedia Input Signal When connecting PC, STB, DVD with Multimedia 1. Pressing the "MULTIMEDIA" button on the remote controller. • Screen changes as follows whenever pressing the “MULTIMEDIA” button. Comp.1 => Comp.2 => HDMI => PC => Comp.1 POWER DISPLAY GUIDE TV/VIDEO MULTIMEDIA 1 2 3 4 5 6 PC Comp.1 HDMI Comp.2 Note: • If sound signal is mono method, connect it to the L-terminal of the sound input terminal.
Selection of Multimedia Input Signal HDMI & PC mode 1. If the message ‘No signal’ appears on the screen, adjust the PC output to a format listed in the Multimedia Input table.
Picture Adjustment Adjustment of Aspect ratio in TV/Video/Component mode 1. Press the "SCREEN SIZE" button • The screen changes as below whenever pressing the "SCREEN SIZE" button. 16:9 => 4:3 => LB[16:9] => LBS[16:9] => 16:9 STILL MUTE SCREEN SIZE CH CAPTION ADD/ ERASE SLEEP PIP CH PIP PIP CH SWAP SOURCE POSITION 4:3 16 : 9 LB(16:9) LBS(16:9) Note : • 16:9 : 16:9 will display a true 16:9 (anamorphic) picture with no aspect distortions. • 4:3 : General TV screen currently broadcasted.
Picture Adjustment Adjustment of the screen in the PC mode 1. Select Picture by pressing the "Menu" button. • The menu screen appears as follows. PREV.CH CH FAV MENU VOL VOL STILL MUTE CH 2. Select PC Screen Mode • Move to PC Screen Mode in the Picture menu by pressing the ” CH ” buttons. • Press the ” VOL ” button. User 50 60 6 N.R Off Color temp PC Screen Mode Select 3. Select and adjust each items. • Move to item what you want by pressing the ” CH ” button.
Picture Adjustment When setting up various screen modes - The user may select various screens designed for a good picture without adjusting the brightness, contrast or color individually. C 1. Picture Mode selects what you want. • Move to Mode in the Picture menu and Select desirable mode using the ” VOL ” buttons.
Picture Adjustment When adjusting the screen to taste - You can enjoy various screens by adjusting Brightness, Contrast, Color, Sharpness, etc to the user’s taste. 1. Select Picture by pressing the “Menu” button. • The menu screen appears as follows. 45 70 55 G R 8 2. Select and adjust each items. • Move to the PICTURE menu. • Whenever pressing the ” CH ” button, you can select in order of Brightness, Contrast, Color, Tint, Sharpness and Noise Reduction.
Sound Adjustment When selecting various sound Effects 1. Sound mode selects what you want. • Move to Effect in the Sound menu. • Select desirable Effect using the ” VOL ” buttons. • Or press the “S.EFFECT” button, then the sound status changes as followed: Off => Voice Effect => Dynamic Bass => Off SWAP P.MODE S.MODE Voice Effect Off Normal Equalizer On Speaker Adjust Dynamic Bass Off Off Off Normal Normal Equalizer Equalizer Speaker Speaker On Note.
Sound Adjustment When adjusting sound to taste - The user can enjoy various sounds by adjusting Balance, AVC, Effect, Equalizer and Digital Volume. 1. Adjust the Balance • Move to Balance in the Sound menu. • Adjust the balance level by using the ” VOL ” buttons. Off Off Normal Equalizer Speaker On Adjust 2. Select AVC (Auto Volume Control) • Move to AVC in the Sound menu. • Select either AVC On/Off using the ” buttons.
Sound Adjustment When adjusting sound to taste 3. Sound mode selects what you want. • Move to Mode in the Sound menu. • Select desirable Sound mode using the ” VOL ” buttons. • Or press the “SOUND MODE” button, then the sound status changes as followed: Normal => Movie => Music => News => User => Normal SWAP SOURCE P.MODE S.MODE MTS S.
Sound Adjustment When adjusting sound to taste 4. Adjust the audio Equalizer • Move to Mode in the Sound menu. • Select User mode using the ” VOL ” buttons. • Select and use the relevant frequency by pressing the ” CH ” buttons. • You can adjust the degree of the frequency by using the ” VOL ” buttons. Note: • Equalizer adjustment is available in User mode. • Equalizer: High quality sound range adjustment method used for audio product. 100/330 Hz: Low sound range 1/1.
Sound Adjustment Choosing a Multi-Channel Sound (MTS) in analog and digital 1. Mono Sound Selection (Mono/Stereo/Mono&SAP/Stereo&SAP) – Analog TV Mode • In Stereo reception if the stereo is weak, you can switch to MONO by pressing the “MTS” button. Then the OSD character will be change to “Mono”. In Mono reception the depth of sound is improved. • To switch back to stereo, press the “MTS” button again. SWAP SOURCE P.MODE S.MODE POSITION MTS S.
Features Closed Caption Viewing Closed Caption (On-Screen Text Messages) - Analog 1. Caption mode selects what you want. • Move to Caption in the Features menu. • Select Caption using the ” VOL ” buttons. Caption PIP Off Background 7 Language English MGDI plus On Parental Control Initialize Select • Select desirable Analog CC using the ” VOL ” buttons. CC on Mute Adjust • The Analog CC changes as followed: Off => CC1 => CC2 => CC3 => CC4 => TX1 => TX2 => TX3 => TX4 Note.
Features Closed Caption Viewing Closed Caption (On-Screen Text Messages) - Digital 1. Caption mode selects what you want. • Move to Caption in the Features menu. • Select Caption using the ” VOL ” buttons. Caption PIP Off Background 7 Language English MGDI plus On Parental Control Initialize Select • Select desirable Digital CC using the ” VOL buttons.
Features PIP/POP PIP (Picture-In-Picture) / POP (Picture-Of-Picture) 1. Watching PIP/POP • By pressing the “PIP” button on the remote controller repeatedly, you can select one of the following settings: SCREEN SIZE CH CAPTION 44 SLEEP PIP CH PIP PIP CH SWAP SOURCE POSITION SCREEN SIZE • If you want to change the position of sub picture, press the “POSITION” button.
Features PIP/POP PIP (Picture-In-Picture) / POP (Picture-Of-Picture) • If you want to swap main for sub, press the “SWAP” button. To swap main for sub change as followed: PIP/POP table PIP CH PIP PIP CH SWAP SOURCE POSITION MTS S.EFFECT P.MODE S.MODE SIZE • If you want to change sub screen input, press the “SOURCE” button. Sub screen change as followed: PIP/POP table CAPTION ADD/ ERASE SLEEP PIP CH PIP PIP CH SWAP SOURCE POSITION PIP/POP mode table. Main\Sub ATV DTV Video1 Video2 Comp.
Features Parental Control Adjustment of Parental Control - The Parental control feature automatically looks out programs that are deemed inappropriate for children. - "Parental control" function is not available in PIP/POP mode. Caption 1. Setting up your password • Move to Parental control in the Features menu. PIP Off Background 7 Language English MGDI plus On Parental Control Initialize Select • The message “Enter password” will appear.
Features Parental Control Adjustment of Parental Control Change Password 2. Setting up Block • Move to Block in the Parental Control • Select either On or Off using in the ” VOL Block Off Movie Rating TV Rating Unblock NO Rating ” buttons. Select Change Password Block Off Movie Rating TV Rating Unblock NO Rating Adjust 3. Setting up Movie ratings • Move to Movie ratings in the Parental Control and press the ” VOL ” buttons.
Features Parental Control Adjustment of Parental Control 4. Setting up TV Rating • Move to Block and select Block to On. • Move to TV Rating in the Parental Control and press the ” VOL ” buttons. • The TV Rating screen will appear. Press the ” CH ” buttons to select one of the six aged based categories: Y: Young children 14: Viewers 14 and over Y7: Children 7 and over MA: Mature audience G: General audience PG: Parental guidance • Press the “DISPLAY” button.
Features ETC When viewing how MGDi improves the picture. 1. Setup of MGDi plus • Move to MGDi plus in the Features menu. • Press the ” VOL ” buttons, and then MGDi plus mode is On. Caption PIP Off Background 7 Language English MGDI plus On Parental Control Initialize Adjust • Press the “MENU” buttons, and then MGDi plus mode is Off. Note: • Crosley's new technology, MGDI plus, brings viewers more detailed, clearer and more natural image with picture compensation algorithm.
Features ETC Selection of Language 1. Select Language • Move to Language in the Features menu. • Select your desired language by pressing the ” VOL button. Then it will be setting automatically.
Time Setting Adjustment of Time 1. Setting the Clock • Move to Clock in the Time menu. • To go to the Clock, press the ” VOL ” buttons. • Place the cursor to AM / PM / Hour / Min. / Month / Day /Year. with ” VOL ” buttons. • Set the AM / PM / Hour / Min. / Month / Day /Year. with the ” CH ” buttons and then presses the “MENU” button to complete. Clock Auto Clock On Off Timer Off Off Time AM 12:00 Wake Timer Off Wake Time AM 12:00 Wake CH. 2 Wake Vol. Eastern Time zone Off DST Adjust 2.
Time Setting Adjustment of Wake Time 4. Setting the Wake Timer / Wake Time / Wake CH / Wake Volume • Move to Wake Timer in the Time menu. • Select the Wake Timer to "On" using the ” VOL ” button. Clock Auto Clock AM 12:00 On Off Timer On Off Time AM 12:00 Wake Timer On Wake Time AM 12:00 Wake CH. 2 Wake Vol. Time zone DST Eastern Off Adjust • Move to Wake Time with the ” CH ” buttons. • To go to Wake Time, press the ” VOL ” buttons. • Place the cursor to AM/PM / Hour / Min.
Time Setting Adjustment of Off Time 5. Setting the Timezone and DST • Move to Timezone in the Time menu. • Select the Timezone to desirable Timezone using the VOL ” button. • The Timezone change as the followed: Central => Mountain => Pacific => Alaska => Hawaii => Newf. => Atlantic => Eastern => Central • Move to DST in the Time menu. and select On, Off with VOL ” buttons. Clock AM 12:00 Auto Clock ” On Off Timer On Off Time AM 12:00 Wake Timer On Wake Time AM 12:00 Wake CH. 2 Wake Vol.
Channel Banner Channel Banner - The channel banner displays information about a channel number, name, broadcasting time, audio service and more. You can see this banner by pressing “DISPLAY” button on the Remote Control. 6 4 5:45 PM 5 6:00 PM 16:9 ENGLISH 8 7 2007 Fri,Sep 14 11:10 AM POWER DISPLAY GUIDE TV/VIDEO MULTIMEDIA 1 2 3 4 5 6 1. General Information Channel Mode: Display the current channel mode (Air/Cable/DTV). Channel Number: Displays the current channel number.
Channel Banner Electronic Program Guide (EPG) (Digital TV mode only) - The DTV Electronic Program Guide (EPG) displays program information about each channel, up to seven days ahead. - You can edit your own profiles, and record programs. - By pressing the “GUIDE” button to access EPG directly, you can see all channels broadcasting now. Note: • The EPG channel is only available when watching DTV channels. 1. Select a desired channel • Select a channel with the ” CH ” buttons.
Troubleshooting Symptoms and Solutions Please check the following items before asking for repair service. Symptom Neither picture nor sound Check items - Check the contact of sockets is all right. - Check the TV main power is on. Picture is OK but no sound - Check the Volume control is set to minimum or mute. Sound is OK, but no colour. - Check the colour control and adjust it properly. - Check the program is in colour and not in black & white. The picture has image.
Troubleshooting In Digital TV mode Some Problems will only occur when viewing DTV channels. Due to the different techniques involved in digital reception, DTV signal quality can be poor even if you appear to have a strong signal when viewing analogue programs. The DTV system requires a good quality signal to provide the best picture. When viewing analogue pictures, interference such as signal reflection from nearby buildings or mountains causes ‘ghosting’, but still provides a viewable picture.
Standard of Product Model C32HDGB C37HDGB C42HDGB Screen Size 32” 37” 42” Aspect Ratio 16:9 16:9 16:9 Resolution 1366 x 768 (WXGA) 1366 x 768 (WXGA) 1366 x 768 (WXGA) Pixel Pitch 170.25 x 510.75 x RGB 0.200 x 0.600 mm x RGB 0.227 x 0.681mm x RGB Contrast Ratio 3000:1 3000:1 3000:1 Dimension(W x H x D) Set Dimension 806 x 626.5 x 230mm 940 x 720 x 328.5mm 1060 x 823 x 328mm Power Consumption Max.
“GOLDEN WARRANTY” Crosley Corporation warrants this product to be free from defects in material and workmanship and agrees to repair or replace this product to remedy such defects. This warranty covers TWO YEAR LABOR and TWO YEAR PARTS from the date of the original purchase. This warranty applies only to product purchased from an authorized Crosley dealer and used within the boundaries of the U.S.A. and Canada.
