TOP-MOUNT REFRIGERATOR Table of Contents ............................................................. www.crosley.
TABLEOF CONTENTS REFRIGERATOR SAFETY .......................................................... 3 Proper Disposal of Your Old Refrigerator .................................... 3 INSTALLING YOUR REFRIGERATOR .......................................... 4 Unpacking Your Refrigerator ....................................................... 4 Location Requirements ................................................................ 4 Electrical Requirements .............................................................
REFRIGERATOR SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance, Always read and obey all safety messages, This symbol alerts you to potential hazards that can kill or hurt you and others. All follow the safety alert symbol and either the word "DANGER" or Thissafety is themessages safety alertwillsymbol. "WARNING.
INSTALLINGYOUR REFRIGERATOR Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. Removing packaging materials • Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue.
_ _ _ _ 9! Cold water supply Connect the ice maker to a cold water line with water pressure between 30 and 120 psi. If you have questions about your water pressure, call your utility company. Connecting to water line: 1. Unplug refrigerator or disconnect power. 2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water. 3. Locate a V2 in. to 11/4in. (12.7 mm to 3.18 cm) vertical COLD water pipe near the refrigerator.
3. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4in. (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer. Freezer door 1. Remove freezer handle assembly as shown. Keep all parts together (see Graphic 2). 2. Remove door hinge hole plug. Move to opposite side as shown (see Graphic 3). 3. Remove door handle sealing screws.
1. Cabinet Hinge Hole Plugs 2 ! o o I !. Door Hinge Hole Plug 1. _6" Hex-Head Hinge Sore WS 3 1. Top Hinge Cover 2. 5/_,, Hex-Head Hinge Screws 3. Top Hinge !. Flat-Head Handle Screws 2. Freezer Handle 1. Door Handle Sealing Screws / Front Wew Side Wew o 1. Center Hinge 2. 5/_6" Hex-Head Hinge Screws ,.h! o , J -p f_ 1. Door Stop Screw 2. Door" Stop Bottom 1 2 !. Door Handle Seal Screw Front Hinge t.Bottom Hinge t. Door Handle Screw Cover" 1. Flat-Head Handle Screw 2.
Door Closing Your refrigerator and one on the want the doors the instructions has two front adjustable rollers - one on the right left. If your refrigerator seems unsteady or you to close easier, adjust the refrigerator's tilt using below: 1. Plug into a grounded 3 prong outlet. 2. Move the refrigerator into its final position. 3. Remove the base grille (see "Base Grille" earlier in this section).
USINGYOUR REFRIGERATOR IMPORTANT: In order to ensure proper temperatures, you need to permit airflow between the refrigerator and freezer sections. As shown in the illustration, cool air enters through the bottom of the freezer section and moves up. Most of the air then flows through the freezer section vents and recirculates under the freezer floor. The rest of the air enters the refrigerator section through the top vent. • Give your refrigerator time to cool down completely before adding food.
REFRIGERATOR FEATURES To turn the ice maker on/off: NOTE: Do not force the wire shut-off arm up or down. • To turn the ice maker on, simply lower the wire shut-off arm. NOTE: Your ice maker has an automatic shut-off. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position. Your model may have some or all of these features.
To slide the shelf from side to side, lift up on the front of shelf and slide to the desired location. Lower shelf to the level position. NOTE: You do not have to remove small items from the shelf before moving it from side to side. You may need to remove larger items. Drawers To remove and replace a drawer: 1. Slide drawer straight out to the stop. Lift the front of the drawer and slide it out the rest of the way. 2. Replace a drawer by sliding it back in fully past the stop.
To remove and replace the meat drawer cover (Style 2 plastic): 1. Remove the meat drawer. Tilt the cover up at the front and pull it forward and out. 2. Replace the meat drawer cover by fitting the notches and rear edge of the cover over rear and center crossbars on the shelf. Lower cover into place and replace the meat drawer. Chilled D ®w®s" " Slide the meat drawer temperature control forward to make the meat drawer less cold or backward to make the drawer more cold.
FREEZER FEATURES Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the "Assistance or Service" section. To remove and replace the shelf: 1. Remove the shelf by lifting the shelf up and pulling straight out. 2.
DOOR FEATURES Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the "Assistance or Service" section. Ad ustc b e u ty The utility compartment and tray slide from one side to the other for more flexible storage.
5. CARING FORYOUR REFRIGERATOR Clean the condenser coils regularly. Coils may need to be cleaned as often as every other month. This may help save energy. Style 1 - Condenser coils behind base grille: • Remove the base grille (see the "Door Removal" section). • Use a vacuum with an extended attachment to clean the condenser coils when they are dusty or dirty. • Replace the base grille when finished. Style 2 - Condenser coils in back of the refrigerator: 6.
TROUBLESHOOTING • Try the solutions suggested here first in order to avoid the cost of an unnecessary service call. Your refrigerator will not operate • Is the power cord unplugged? Plug into a grounded 3 prong outlet. • Has a household fuse or circuit breaker tripped? Replace the fuse or reset the circuit breaker. • Is the Refrigerator Control turned to the OFF position? See the "Setting the Control(s)" section.
The water dispenser will not operate Has the water system not filled? The water system needs to be filled the first time it is used, Use a sturdy container to depress the water dispenser until water begins to flow, Dispense and discard 2 to 3 gallons (8 to 12 L) of water. This will take approximately 6 to 7 minutes and will help clear air from the line, Additional flushing may be required in some households, See the "Water Dispenser" section.
ASSISTANCEOR SERVICE Before calling for assistance or service, please check "Troubleshooting." It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request. If you need replacement parts If you need to order replacement parts, we recommend that you only use factory specified replacement parts.
CROSLEY ®REFRIGERATOR WARRANTY ONE-YEAR FULL WARRANTY ON REFRIGERATOR For one year from the date of purchase, when this refrigerator (excluding the water filter) is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for factory specified replacement parts and repair labor costs to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
