PART LIST Left Vertical Pane! | Right Vertical Panel Fixed Shelf Front Top Rail Left Pane! 1PC 1PC 1PC 1PC 1PC Right Panel Back Rail Back Panel Middle Back Panel | Back Horizontal Rail 1PC PCS PCS 1PC PCS Bottom Panel Top Panel Left Door Panel | Right Door Panel | Left Middle Door Panel 1PC 1PC 1PC 1PC he Right Middle Door | Adjustable Shelf | Middle Adjustable Support Rail Panel Shelf 1PC 4 PCS 1PC 1PC
HARDWARE LIST Cam Lock Cam Bolt Wood Dowel! Screw Hex Socket Head Brit 20 PCS (Extra 2) 20 PCS 42 PCS 7 PCS (Extra 1) 8 PCS Barr! Nut Shelf Holder Knob Round Head Bolt Magnet 8 PCS PCS 4 PCS 4 PCS PCS #12 #13 (Spare Part} Double Magnet Round Head Allen Wrench Safety Strap Kit Pin Hinge Screw 1PC 6 PCS (Extra 1} 1PC 18ET (Extra 4) ADDITIONAL TOOLS (Not Provided) Note: it is not recommended to use power tools during assembly. & Phillips Head Screwdriver Note: Wood dowses are intended for alignment.
fillips head screwdriver. longer visible. NOTE: Cam locks must rotate a full 180°. Ses pictured insert. Step 1. Insert cam bolts {part #2) into left vertical panel {part A), right vertical panel (part B), left pane! (part E), right pane! (part F), bottom panel (part K} and top panel {part L) using NOTE: Do not over tighten cam obits. Stop tightening once threads on cam bolt are no Step 2.
Step 3. Carefully turn unit upright. Attach front top rail (part D) to assembled unit (parts A & B) using wood dowels (part #3), screws (part #4) and fillips head screwdriver. Step 4. Carefully tum unit upside down. Attach left panel {part E) fo front top rail {part D) using cam lock {part #1) and wood sows! {part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 5. Step 6. Attach back rail (part G) to left panel (part E) using cam lock (part #1) and wood dowel (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert. Place back horizontal rails (part J) into back rail {part GO) using wood dowels {part #3). Slide back panels (part H) and middle back panel (part 1} into the grooves of back horizontal rails {part J) and back rail (part G).
Step 7. Attach right panel {part F) to front top rail {part D) and back rails {part G) using cam locks (part #1) and wood dowels (part #3). Attach magnets (part #10) to front top rail {part D) and double magnet {part #11) to fixed shelf {part C) using round head screws {part #12) and fillips head screwdriver. NOTE: Cam locks must rotate a full 180°. See pictured insert. A burn clocking fo fasten Step 8.
Step 8. Attach bottom panel (part K) to assembled unit {parts using cam lock {part #1), wood dowels {part #3), hex socket head bolts (part #5), barrel nuts {part #8) and Allen wrench (part #13). Attach legs using instruction manual and hardware included inside leg packaging. NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 10. Carefully turn unit upright. Attach top panel (part L) to assembled unit (pairs A,B, using cam locks (part #1), wood dowels (part #3), screw (part #4) and fillips head screwdriver. NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 11. Attach knobs (part #8) to left door panel (part M), right door panel (part N), left middies door panel {part O) and right middies door panel (part P) using round head bolts (part #9) and fillips head screwdriver. Attach left door panel (part M), right door panel (part N), left middle door panel {part O) and right middle door panel {part P} by placing bottom pin hinge {per-installed in door} in the per-drilled hole of bottom pane! (part K).
Step 12. Place shelf holders (part #7) into desired position and then slide adjustable shelves (part Q) and middle adjustable shelf (part R) into place.
Safety Strap Kit 1 SET Wall Anchor 1PC Washer PCS Cc D Short Screw Long Screw Safety Wall Strap 1PC 1PC 1PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping, damage and/or injury. 1. Insert short screw (C) through washer (B) and safety wall strap (E) and attach to back of top panel {part L) using fillips head screwdriver. 2. Drill a 11/32” hole where you want to secure the unit.