® TOP-MOUNT REFRIGERATOR Table of Contents..........2 www.crosley.
TABLE OF CONTENTS REFRIGERATOR SAFETY.......................................................... 3 INSTALLING YOUR REFRIGERATOR ..........................................4 Unpacking Your Refrigerator .......................................................4 Space Requirements....................................................................4 Electrical Requirements ...............................................................5 Connecting the Refrigerator to a Water Source ..........................
REFRIGERATOR SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
Cleaning before use INSTALLING YOUR REFRIGERATOR After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Caring for your Refrigerator” section. Important information to know about glass shelves and covers: Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.
Electrical Requirements WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection: Recommended grounding method A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required.
. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the ¹⁄₄ in. drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing. 7. Slip compression sleeve and compression nut on copper tubing as shown.
Refrigerator Doors: Removing, Reversing (optional) and Replacing TOOLS NEEDED: ⁵⁄₁₆ in. hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, ⁵⁄₁₆ in. open-end wrench, flat 2 in. putty knife. IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors. Door Removal & Replacement Door Swing Reversal (optional) 1-2 2 Base Grille 1 1 1.
Door and hinge removal ⁵⁄₁₆” Hex Head Hinge Screw 1. Unplug refrigerator or disconnect power. 2. Open refrigerator door and remove base grille from the bottom front of the refrigerator (see Base Grille graphic). 3. Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet. NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working. 4.
4. Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator. NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws. 5.
Setting the Control(s) Adjusting Control Settings For your convenience, the refrigerator controls are preset at the factory. Controls for the refrigerator and freezer are located in the top of the refrigerator section. When you first install your refrigerator, make sure that the control(s) are still preset. The control(s) should be at the “mid-settings” as shown for each style of control. Mid-setting “3” Give the refrigerator time to cool down completely before adding food.
CONDITION/REASON: REFRIGERATOR section too cold ■ ■ Controls not set correctly for your conditions Blocked air stream FREEZER section too cold ■ Controls not set correctly for your conditions ■ Blocked air stream RECOMMENDED ADJUSTMENT: Turn REFRIGERATOR Control or TEMPERATURE Control to next lower number, wait 24 hours, then recheck Move items out of air stream Turn FREEZER Control or TEMPERATURE Control to next lower number, wait 24 hours, then recheck To remove and replace a shelf in a metal fra
To remove and replace the shelf track: 1. Remove the shelf track by lifting both sides of the track slightly and pulling the track straight out. 2. Replace the track by guiding the track hooks into the shelf support slots on the back wall. NOTE: Make sure that both sets of track hooks are in the slots and that the slots are parallel with each other. 3. Push the track back and down securely into the shelf supports.
To replace crisper(s) cover: NOTE: Before reinstalling the cover, make sure the U-shaped reinforcement bar is reinstalled in the front edge of the crisper cover. 1. Fit back of cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place. 2. Slide rear of glass insert into cover frame and lower front into place. Wine or Can/Bottle Rack (on some models - Accessory) To remove and replace the wine rack (left) or can/bottle rack (right): 1.
To turn the ice maker off: Automatic turn off: As ice is made, the ice cubes will fill the ice storage bin, and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position. ■ ■ Manual turn off: Lift the wire shut-off arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate. To replace the shelf: 1. Tilt the shelf and insert into freezer compartment. 2. Insert one end of the shelf all the way into the center of the shelf supports.
Pull-out Freezer Floor Door Bins (on some models) (on some models) To remove and replace the freezer floor: 1. Lift both back “fences” up and out. 2. Remove the freezer floor by pulling it out about 1 in. (25.40 mm) with one hand around the air tower section (center back) and one hand at center front. 3. Lift up floor at rear until hooks release from cabinet and pull the floor out the rest of the way. 4.
To adjust the utility compartment or tray: 1. Lift the front slightly and slide to desired position. 2. Lower front to lock into place. Flip-up Door Shelf (on some models) The shelf bottom flips up so you can store taller items in the door shelf below. When in the down position, the shelf is strong enough to hold up to 10 pounds (4.5 kg). ■ Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.
Power Interruptions If the electricity in your house goes off, call the power company and ask how long it will be off. 1. If the power will be out for 24 hours or less, keep both refrigerator doors closed to help food stay cold and frozen. 2. If the power will be out for more than 24 hours: a) Remove all frozen food and store it in a frozen food locker. OR b) Place 2 lbs. (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for two to four days.
The motor seems to run too much ■ Is the room temperature hotter than normal? Expect the motor to run longer under warm conditions. At normal room temperatures, expect your motor to run about 40% to 80% of the time. Under warmer conditions, expect it to run even more of the time. ■ Has a large amount of food just been added to the refrigerator? Adding a large amount of food warms the refrigerator. It is normal for the motor to run longer in order to cool the refrigerator back down.
There is interior moisture build-up ■ ■ Are the air vents blocked in the refrigerator? Remove any objects from in front of the air vents. Refer to “Ensuring Proper Air Circulation” for the location of air vents. Is the door opened often? To avoid humidity build-up, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is removed. (When the door is opened, humidity from the room air enters the refrigerator.
CROSLEY® REFRIGERATOR WARRANTY ONE-YEAR FULL WARRANTY ON REFRIGERATOR For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for factory specified replacement parts and repair labor costs to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.