Instruction Manual

1911
BB Repeater CO
2
Airsoft gun Pistol
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN
Crosman Corporation
7629 Routes 5 & 20
Bloomeld, NY 14469
www.crosman.com
1-800-724-7486
Made in the U.S.A. with some foreign components. AS1911-515
THIS IS NOT A TOY. ADULT SUPERVISION REQUIRED. MISUSE OR CARELESS USE MAY
CAUSE SERIOUS INJURY, ESPECIALLY TO THE EYE. EYE PROTECTION MUST BE USED BY THE USER AND
ANY PERSON WITHIN RANGE. MAY BE DANGEROUS UP TO 100 YARDS (91.44 METERS). READ OWNER’S
MANUAL BEFORE USING.
Notice: Read this owner’s manual completely. And remember, this airsoft gun is not a toy. Treat it with the same
respect you would a rearm. Always carefully follow the safety instructions found in this owner’s manual and keep this
manual in a safe place for future use.
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR SHOOTING GLASSES
TO PROTECT YOUR EYES.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS REGARDING THE USE
AND OWNERSHIP OF THIS AIRSOFT GUN.
Do not brandish or display this airsoft gun in public – it may confuse people and may be a
crime. Police and others may think it is a rearm. Do not change the coloration and markings to make it look
more like a rearm. That is dangerous and may be a crime.
This product contains lead, a chemical known to the State of California to cause cancer and
birth defects (or other reproductive harm.)
If you have any questions regarding your AIRSOFT GUN, please contact Crosman at 1-800-724-7486, 585-657-6161
or www.crosman.com.
1. Safety First
•
ALWAYS treat the airsoft gun gun as though it is loaded and ready to re and with the same respect
you would a rearm.
• ALWAYS store the airsoft gun unloaded.
• ALWAYS store the airsoft gun away from children.
• ALWAYS aim in a SAFE DIRECTION.
• ALWAYS keep the muzzle of the airsoft gun pointed in a SAFE DIRECTION.
• ALWAYS keep your nger off the trigger and out of the trigger guard until ready to shoot.
• ALWAYS keep the airsoft gun “ON SAFE” until you are ready to shoot (see section 3A).
• ALWAYS check to see if the airsoft gun is “ON SAFE” (see section 3A) and unloaded when getting it
from another person.
• ALWAYS have you and others wear shooting glasses to protect your eyes.
• ALWAYS wear shooting glasses over eye glasses if your prescription or reading glasses are not
safety glasses.
• ALWAYS place the backstop in a location that will be safe should the backstop fail.
• ALWAYS check your backstop for wear before and after each use. All backstops are subject to
wear and will eventually fail. Replace your backstop if the surface is worn or damaged, or if a rico-
chet occurs.
• ALWAYS use the proper size BB in your airsoft gun Check the markings on your airsoft gun to verify
the BB size- 6mm.
• NEVER reuse ammunition.
• NEVER shoot at hard surfaces or at the surface of water. The BB may bounce off or ricochet and hit
someone or something you had not intended to hit.
• NEVER point the airsoft gun at any person or at anything you do not intend to shoot.
2.
Learning the Parts of Your New Airsoft Gun
Learning the names of the parts of your airsoft gun will help you understand your owner’s manual.
A. Muzzle
B. Front Sight
C. Safety
D. Slide
E. Rear Sight
F. Grip cover
G. Piercing wing
H. Magazine Release Button
I. Magazine
J. Trigger
K. Trigger Guard
3. Operating the Safety
A. To Put the Airsoft Gun “ON SAFE:”
Push the safety in and all the way forward toward the “S” for “ON SAFE” (Fig. 2).
The safety is not “ON SAFE” unless it is pushed all the way forward.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is
“ON SAFE”, you should continue to handle the airsoft gun safely.
NEVER point the airsoft gun at any person. NEVER point the airsoft gun at
anything you do not intend to shoot.
B. To take the Airsoft Gun “OFF SAFE”
Push the safety in and all the way back toward the “F” for “OFF SAFE” or “FIRE”.
When the Safety button on the left side of the AIRSOFT GUN is all the way back, it
is “OFF SAFE” and can be red.
4. Installing and Removing the CO
2
Cartridge
A. Installing a New CO
2
Cartridge
Keep hands away from escaping CO
2
gas. Escaping CO
2
gas can cause frostbite if allowed
to come in contact with skin. Always make sure the CO
2
cartridge is empty before attempting to remove it from
the airsoft gun by slowly turning the WING counter-clockwise all the way until you no longer hear the escape of
CO
2
gas.
1. Put the airsoft gun “ON SAFE” (see Section 3A).
2. Make sure the airsoft gun is UNLOADED and POINTED IN A
SAFE DIRECTION.
3. With your hand under the magazine, push the magazine release but-
ton to remove the magazine
4. Remove the grip cover from the left side of the airsoft gun by lifting it
at the indentation on the bottom of the grip.
5. Turn the piercing wing clockwise, to bring the piercing knob down.
6. Insert a new CO
2
cartridge into the airsoft gun with the small neck of
the cartridge pointing toward the piercing assembly (Fig. 3).
7. With your thumb and nger, turn the piercing wing clockwise until
tight to pierce the CO
2
cartridge. Never use any tool on the piercing
wing. Over-tightening can cause injury to you or damage to your
airsoft gun.
8. Release the piercing wing and snap the grip covers back into place.
9. Point the airsoft gun in a SAFE DIRECTION, take “OFF SAFE” (See Step 3B) and pull the trigger.
10. If the airsoft gun does not make a popping noise after pulling the trigger, the CO
2
is not
being discharged. In that event, tighten the piercing wing a little more, point the airsoft gun
in a SAFE DIRECTION and pull the trigger until there is a popping noise, which will mean
the airsoft gun is releasing CO
2
with each pull of the trigger.
CAUTION: We recommend the use of CROSMAN
®
POWERLET
®
CO
2
cartridges. They are made to
t your airsoft gun. Other brands of CO
2
cartridges may not t properly may result in injury to you or
damage to your airsoft gun. Do not store your airsoft gun with a CO
2
cartridge in it.
B. Removing the CO
2
Cartridge
1. Put the airsoft gun “ON SAFE” (See Step 3A).
2. Make sure the airsoft gun is unloaded (See Step 5B).
3. Point the airsoft gun in a SAFE DIRECTION.
4. Remove the grips.
5. Slowly turn the piercing wing counter clockwise, to release the CO
2
being careful not to
come in contact with the escaping gas.
6. Tip out the empty cartridge. It may be cold to the touch.
5. Loading and Unloading Plastic BBs
A. Loading Plastic BBs
1. Make sure the airsoft gun is “ON SAFE” (See Step 3A) and pointed in a SAFE DIRECTION.
2. With your hand under the magazine, push the magazine release button to remove
the magazine.
3. Pull down the BB follower tab (g. 4) and lock in place.
4. Insert up to 16 plastic BBs into the BB loading hole on the front of the magazine.
5. Place a nger over the end of the magazine where the BBs will exit.
6. With the magazine pointed in a SAFE DIRECTION, release the BB Follower tab.
NOTE: Releasing the BB follower tab quickly, or without the end covered, could allow BBs to exit
the magazine.
7. Insert the loaded magazine into the AIRSOFT GUN
8. Your airsoft gun is now loaded and ready to re, after reading the entire manual.
B. Unloading Plastic BBs
Even though you go through the unloading procedure, continue to treat the AIRSOFT GUN as
though it were loaded. Do not point at anything you do not intend to shoot.
1. Make sure the airsoft gun is “ON SAFE” (See Step 3A) and pointed in a SAFE DIRECTION.
2. With your hand under the magazine, push the magazine release button to remove the magazine.
3. Pull and hold down the BB follower tab.
4. Tip the magazine until all the plastic BBs fall out of the hole.
5. If a BB is still visible in the top of the magazine, push the BB out of the magazine.
6. Aim the airsoft gun in a SAFE DIRECTION; insert the magazine into gun, take it “OFF SAFE” (See Step 3B)
and re.
Fig. 2
Fig. 3
Fig. 4
7. Repeat this procedure several times until you are sure you are no longer ring BBs.
NOTE: The airsoft gun must be charged with CO
2
when following these steps but remember, do not store your airsoft
gun with a CO
2
cartridge in it.
6. Sighting the Gun
1. The airsoft gun is correctly aimed when the front sight blade is positioned in
the notch of the rear sight.
2. The top of the front sight blade should be even with the top of the notch in
the rear sight. The bulls-eye should appear to rest on the top of the front
sight. (Fig.5)
3. When you are sure of your target and backstop, and the area around the
target is clear, take the airsoft gun “OFF SAFE” (see section 3B) and pull the
trigger to re.
7. Maintaining Your Airsoft gun
A. General
1. Put 1 drop of Crosman 0241 Pellgunoil
®
on the tip of every CO
2
cylinder in
order to properly maintain your airsoft gun.
2. DO NOT use petroleum distillate based oil or solvent and DO NOT over oil
as this can cause damage to your airsoft gun.
3. DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the
airsoft gun in any way inconsistent with this manual may make your airsoft
gun unsafe to use, cause serious injury or death, and will void the warranty.
4. If you drop your airsoft gun, visually inspect for damage before you use
it again.
5. If anything seems changed, like a shorter or weaker trigger pull, this may
mean worn out or broken parts. Call Crosman customer service for assis-
tance before using your airsoft gun again.
B. Clearing a Jam
1. Never look down the barrel to see if a jam has been cleared.
2. Make sure the airsoft gun is ‘ON SAFE” and pointed in a SAFE DIRECTION.
3. Remove the CO
2
cartridge (following section 4B)
4. Remove magazine.
5. Insert the tapered end of the cleaning rod (rod not included) into the barrel.
6. CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
7. Reinstall the magazine and test gun.
SPECIFICATIONS
Mechanism
BB Repeater
Safety
Lever
Power Source
12 gram CO
2
cartridge
Sights
Front: Fixed Blade
Rear: Fixed Notch
Caliber
6mm
Ammunition
Plastic BB
Length
8.9 inches
Capacity
Up to 16 BB
Weight
2 lbs. 1 oz.
Velocity
Up to 420 fps
PERFORMANCE: Many factors can affect velocity, including brand of projectile, type of projectile and
barrel condition.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our customer service representatives will help. You can get answers to frequently asked questions at
www.crosman.com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at
1-800- 724-7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO
DISASSEMBLE IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no
warranty responsibility under such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may cause
your product to malfunction and may void your warranty.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material and
workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modication or failure to perform
normal maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL
EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to
product. Package and return to Crosman Corporation, Routes 5 & 20, Bloomeld, NY 14469.
International Customers: Please return product to your nearest distributor. If you do not know your distributor,
please call 585-657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be
preempted, it shall not be applicable. This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.
Fig. 5