OPERATING MANUAL CROSSOVER 2.0 SERIES In a class by itself MODEL NO. WHLFP817M WHLFP817MI WA S H E R I N S TA L L AT I O N M A N UA L DOC. NO. 0020506871C EDITION 23.
ATTENTION INSTALLER Four transportation bolts are installed in the rear of the machine, to protect the suspension and tub assembly from damage during shipment. REMOVE ALL FOUR BOLTS AND PLASTIC TUBES THROUGH WHICH THE BOLTS PASS BEFORE OPERATING THE MACHINE!! See instructions later in this manual.
Installation Manual WHLFP817M WHLFP817MI WARNING: ALL OPERATING AND MAINTENANCE PROCEDURES SHOWN IN THIS MANUAL MUST BE FOLLOWED AT THE FREQUENCY SPECIFIED FOR PROPER OPERATION OF YOUR MACHINE. PLEASE ENTER THE FOLLOWING INFORMATION AS IT APPEARS ON THE MACHINE(S) DATA PLATE(S). MACHINE MODEL MACHINE SERIAL NUMBER(S) ELECTRICAL CHARACTERISTICS: VOLTS, PHASE, HZ. KEEP THIS MANUAL IN A SECURE PLACE FOR FUTURE REFERENCE.
Intentionally blank
IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES MESURES DE SECURITE WARNING - To reduce the risk of fire, electric chock, or injury to persons when using your appliance: AVERTISSEMENT - Pour réduire les risques d´incendie, de choc électrique ou de blessure quand, I´appareil est utilisé: 1. Read all instructions before using the appliance. Lire toutes les instructions avant d’utiliser l’appareil. 2. This machine must be installed according to the installation instructions.
NOTICE TO: OWNERS, OPERATORS AND DEALERS IMPROPER INSTALLATION AND INADEQUATE MAINTENANCE, POOR HOUSEKEEPING AND WILLFUL NEGLECT OR BYPASSING OF SAFETY DEVICES MAY RESULT IN SERIOUS ACCIDENTS OR INJURY. TO ASSURE THE SAFETY OF CUSTOMERS AND/OR OPERATORS OF YOUR MACHINE, THE FOLLOWING MAINTENANCE CHECKS MUST BE PERFORMED ON A DAILY BASIS.
NOTICE TO INSTALLER Improper installation of this machine: • May cause serious damage to the machine. • May result in other property damage. • May cause personal injury. • Will void the manufacturer’s warranty. Location Requirements • The location for your washer should have a flat and even floor. This will improve performance, minimize noise and decrease washer movement. • The unit can be installed in a laundry room, or other recessed area. Additional Requirements • A grounded electrical outlet.
Contents Technical Data................................................................................................... 1:1 Installation......................................................................................................... 2:1 Water Connections......................................................................................3:1 Drain Connection......................................................................................... 4:1 Connection of External Liquid Supplies........
Technical Data Technical Data Innerdrum volume diameter Drum speed wash extraction litres/ft3 mm/inch 98/3.5 554/21 13/16 rpm max rpm 45 1000 G-factor Weight, net kg/lbs 306 136/300 Connections Water valves connection DN20 3/4" Garden Hose via included hoses Rec. water pressure psi kPa 30-90 200-600 Functioning limits for water valve psi kPa 8-145 50-1000 Capacity at 45 psi (300 kPa) gallon/min liter/min Drain hose Draining capacity 2.
Technical Data 1:2 1 2 3 4 5 6 7 8 9 Power Line Air Vent for Safety Cold Water Hot Water Drain Coin Meter (coin operated models only) Control Panel Detergent Dispenser Door D 6 7 8 1 2 3 4 5 C B A 9 E NOTES: A B C D E 1098mm = 43 1/4 inch 584mm = 23 inch 310mm = 12 3/16 inch 686mm = 27 inch 765mm = 30 1/8 inch
Installation 2:1 Installation For safety, two people should install this product. Leave the machine on the transport pallet until it can be placed in the final, prepared position. First remove all the packing materials. Upon opening of the package, water drops may be seen on the plastic bag and the drum. This is a normal phenomenon resulting from water tests in the factory. NOTE: 1. A bottom cover plate is wrapped in the top of the packing material. 2. Be careful while handling the bottom cover. 3.
Installation 2:2 Transportation Bolts The washer is fitted with transportation bolts to prevent internal damage during transportation. Transportation bolts must be removed before using the washer. Removing Transportation Bolts Fig. 1. 2 Unscrew the 4 bolts with a wrench. Remove the lower 2 bolts first, then the upper two. One of the bolts retains the power cord of the washer to prevent operating without removing bolts. Fig. 2 Brace 2.
Installation Siting Install the machine close to a drain standpipe or floor drain, and within 4 feet of the water supply spigots. In order to make installation and servicing the machine easier the following clearances are recommended: Fig. • 4 • At least 20 inches (500 mm) between the machine and the wall behind. Minimum 1 inch (25 mm) to next machine if more than one machine is installed in a row. Floor • The floor must be smooth and hard. Do not install the machine on carpet or other soft material.
Installation 3:1 Water Connections All inlet connections to the machine are to be fitted with manual shut-off valves and filters, to facilitate installation and servicing. NOTE: The inlet filter screens are provided inside the machine’s connection fittings. Water pipes and hoses should be flushed clean before installation. After installation, hoses should hang in gentle arcs. The machine is equipped with two water inlet fittings, one for hot water and one for cold.
Installation Water Type Fig.
Installation 4:1 Drain Connection Connect the machine’s drain hose to the back of the washer, using the spring clamp provided in the accessories package. Avoid sharp bends in the hose which may prevent proper draining. Fig. • 1 • You can connect the drain hose to a sewer stand pipe. If you do this, make sure that the outlet hose will not come out of the stand pipe. You can connect the drain outlet to a sink or basin. If you do this, make sure the outlet hose will not come out of the sink or basin.
Installation Electrical installation must be carried out by licensed, qualified personnel! 5:1 All optional equipment connected must be EMC-approved to EN 50081-1 or EN 500822. Connection of External Price Reduction Control Signal 1 Fig. Optional harness 0020400145C is available for price 1 reduction (promotion) activation. Contact Laundrylux for more information about other timer-based kits that are available for this function.
Installation 5:2 Electrical Connections This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounded plug. The plug must be inserted into an outlet that is properly installed and grounded. • Improper use of the plug can result in a risk of electric shock.
Function Checks Function Checks Perform the following checks once the machine is installed: • Open the water supply valves. • Press the START button or, if needed, insert coins and press START. Check: • that the drum rotates normally and that there are no unusual noises. • that there are no leaks in water supply/drain connections. • that water passes through the detergent compartment and fabric conditioner compartments. • that the door cannot be opened using reasonable force during a program.
Preventive Maintenance 7:1 To keep your machine in proper working order, follow the preventive maintenance recommendations provided below. The maintenance interval should be adjusted according to machine usage. Leave the loading door open when the machine is not in use. Daily • Check the door and door lock: - Open the door and try starting the machine. The machine MUST NOT START. - Close the door, start the machine and try opening the door using reasonable force.
Sales and Administration: (516) 371-4400 Spare Parts: (516) 371-2000 Technical Support: (516) 371-0700 En Mexico: 001-800-010-1010 461 Doughty Blvd., Inwood, NY 11096 laundrylux.
