Data Sheet

68
APPLICATION
Cam Bloc
Control of a group of 8 integral cam wheels.
Angular Cam Timer
Cam timer with the angle made by the cams as the
command input.
Pumps management
Pumps Management (Tank Management with circular pump
changeover).
Sunrise Sunset Time
Calculation of the sunrise and sunset time in relation to the latitude
and longitude.
Solar Tracking one Axis
Calculation of the sun's position so that a sun dial can
be placed.
Analog PID Regulation
(8 bits)
Temperature control (pressure or other) with 8 bitsanalog output.
PWM PID Regulation
(8 bits)
Temperature control (pressure or other) with 8 bitsdigital output.
Pressure Gain
Interface between a Pressure Sensor and the Millenium 3 logic
controller.
Flow
Calculation of the flow of a liquid in a pipe using a differential
pressure element or by measuring the dynamic pressure.
Level
Calculation of the level of a liquid with or without constant density, in
an open or closed tank, using pressure sensors.
CTN 1
Temperature measurement
It is dedicated to CTN1 (-25 to +85 °C).
CTN 2
Temperature measurement.
It is designed for CTN2 type NTCs (-35°C to +120°C).
CTN 3
Temperature measurement.
It is designed for CTN3 type NTCs (0°C to +200°C).
LUX-I
Light measurement It is designed for photoresistors and
internal light meters.
Twilight
Calculation of the sunrise and sunset times and also the twilight
times in relation to the latitude and longitude read on the function
block inputs.
Solar Tracking Dual Axis
Calculation of the sun's position so that a sun dial can be placed. This
positioning depends on the two angles calculated by the function: the
elevation angle and the azimuth angle.
Swimming Pool Filtration
Filtration time information in relation to the water
temperature.
Defrost
Defrost cycle management
Heat Curve
Modulation of the heating water temperature according to the
atmospheric conditions. The function uses automatic regulation
depending on the temperature outdoors called the temperature curve
or "water ratio".
Analog PID Regulator
(Auto-tuning)
Auto-tuning proportional-integral-derivative (PID)
controller.
CALCUL
Gain
Conversion of an analog value by changing the scale and offset.
Add/Subb
Simple operations on integers: Addition and/or Subtraction.
Mul/Div
Simple operations on integers: Multiplication and/or Division.
ADD/SUB 2 Inputs
The ADD-SUB (Addition or Subtraction) function is used to perform
simple operations on integers.
Sin/Cos
Calculation of the cos and sin of an angle between 0° and 90°.
Square Root
Calculation of the square root of the number present as an input with
accuracy to two decimal points.
Bit Multiplexer
Copy of the selected A or B input to the outputs Q and/Q.
Multiplexer A B
Multiplexing function on 2 analog values.
Demultiplexer
Demultiplexing of integers.
Used to direct the value of the input to one of the 4 outputs.
Multiplexer
Multiplexing word inputs.
Used to direct the value of one of the selected inputs to a predefined
output.
Dec/Bin
Break down of an integer type input (16 bits) into 16
bit type outputs.
Bin/Dec
Make up of an integer type output (16 bits) from 16 bit type inputs.
SPLIT 16 bits to 4
Split of a 16-bit word into four 16-bit words with values between 0
and 15.
SPLIT 16 bits to 2
Split of a 16-bit word into two 16-bit words with values between 0
and 255.
Word Shift Register
Shifting of the 16-bit words on each rising edge of the clock.
Shift Register
Shifting of information by saving it to the memory (shifting of bits in a
16-bit word on each rising edge of the clock).
Transfer Function
Table of correspondence between the X input and the Y output.The
table of correspondence is created from a csv file
Transfer Function 50
values
Table of correspondence between the X input and the Y output.The
table of correspondence (50 rows max) is created from a sv file
Timer Transfer Function
Correspondence table for the Minutes operating time and the Y
output.
Timer Transfer Function
50 values
Correspondence table for the Minutes operating time and the Y
output. (50 Values)
PROG
Constant On
Constant On
Constant Off
Constant Off
Yes Bit
Copy of the input to the output. (very helpful when macros are being
used)
Numerical Constant
Integer with a value between -32768 and +32767.
Yes Num
Copy of the input to the output. (very helpful when macros are being
used)
Memory
Saving of a value between -32768 and 32767.
Storage
Storage of data values with an average value.
Archive
Saving of two values simultaneously with the
information relating to their time-stamping.
Random
Generation of a pseudo-random value between the min
and max values set by the user.
GRAFCET SFC
Resettable Initial Step
When RESET function is activated, activation of the STEP OUTPUT for the
function, which is the initial step, and reinitialization of all of the ther active steps.
Initial Step
Initial step of an SFC chart
Step
A step of an SFC chart.
Or Divergence Step
Transition of one step to be simultaneously made toward one or two
steps.
Or Convergence
Transition of one to four step(s) to be simultaneously made toward
one step.
And Divergence
Transition of one or two steps to be simultaneously made toward two
steps.
And Convergence Step
Transition of two steps to be simultaneously made toward one step.
Wait SFC Step
Set up of a wait phase or step for a PLC or a device.
Move SFC Step
Set up of a move step for a motor controlled by the PLC to a position
specified on the TARGET input.
Motor Multiplexer
Combination of the motor control signals produced by two linked
MOVE SFC steps.
PROG
Hour Minute
Indication of the time from the controller (hour and minutes).
Hr Mn Converter
Conversion of a time period in the "hour : minute" format to minutes
and vice versa.
Controller Status
Access to the controller states and modify the behaviour of its FBD
and/or SFC program depending on these states.
Summertime
Active function throughout summer time, and inactive throughout
winter time.
MACROS
Display 15 texts
Display of 15 texts one after each other with 15 Displays Function
Blocs
Scroll 4 lines
Scroll down of a text of four lines on the screen of the Controller
My Macro
Possibility to create a personal macro library and to store them in the
Macro tab.
Function blocks
www.crouzet-automation.com