User's Manual

ManualsBrandsCrow Electronic Engineering ManualsElectronicsDECT ULE transceiver

MOUNTING THE FLOOD SENSOR

Mounting using adhesive tape:

1. Reveal first side of the smaller

adhesive tape strip and attach it

to the flood sensor (B).

2. Reveal the adhesive tape

second side and attach the flood

sensor to the wall.

Mounting using screws:

1. Remove the screw cover

(A) from the Flood sensor

unit (B).

2. Mount the Flood sensor

using the screw (C).

In both cases:

Mount the sensor at the

desired fluid detection height from the floor (D).

The fluid has to reach the two exposed Golden

contacts (E) in order to give an alarm.

MOUNTING THE DETECTOR

Mounting using screws:

1. Separate the device from its bracket by

unscrewing the holding screw and tilting the

front cover as shown in Figure 1.

2. Mount the Bracket to the wall using the 3 screws

and make sure the tamper screw (the middle

screw) is tightened as seen on Figure 7.

3. Perform the Pairing process as described above

in this document.

4. Place the device in the Bracket by inserting it

back into appropriate position and validate

receiving the Tamper Alert Off indication.

5. Fasten holding screw and close screw cover.

Mounting using adhesive tape:

1. Remove the first protective paper of the

adhesive tape strip and attach it to the back side

of the device bracket as seen on Figure 7.

2. Remove the second protective paper of the

adhesive tape strip and attach the bracket to the

wall.

3. Continue steps 3-5 above.

FIGURE 7 – MOUNTING THE DEVICE

BATTERY REPLACEMENT

1. Open the screw cover and unscrew the

holding screw as shown in Figure 1.

2. Separate the device from the Bracket by tilting

the front cover as shown in Figure 1.

3. Remove the in used battery from the device.

4. Install the new battery in the correct polarity

marking – as seen in Figure 4.

5. Wait until the Red LED stops blinking.

6. In case the device was paired to a Base

Station the device should automatically

the Green LED shall constantly light On for 3

seconds.

7. Place the device in the Bracket by inserting it

back into appropriate position and validate

receiving the Tamper Alert Off indication on

your Application / Base Station.

8. Fasten the holding screw and close the screw

cover.

FCC & IC STATEMENT

FCC ID: NFC-CRDU

IC: 8164A-CRDU

This device complies with FCC Rules Part 15 and with

Industry Canada license-exempt RSS standard(s).

Operation is subject to two conditions: (1) This device

may not cause harmful interference, and (2) this device

must accept any interference that may be received or

that may cause undesired operation.

Canada: Le présent appareil est conforme aux CNR

d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux

deux conditions suivantes : (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil

doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en

compromettre le fonctionnement.

WARNING:

Changes or modifications to this equipment not

expressly approved by the party responsible for

compliance (Crow Electronic Engineering Ltd.) could

void the user’s authority to operate the equipment.

FCC & IC STATEMENT (Continue)

Note: The digital circuit of this device has been tested

and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and

receiver.

-Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV

technician for help.

REGULATORY APPROVALS

This DECT ULE detector conforms to the essential

requirements set out by:

 RTTE directive:1999/5/EC

 EMC directive: 2004/108/EC

 Low Voltage directive: 2006/95/EC

 RoHS directive: 2011/65/EU

Harmonized Standards applicable to this products are:

 EN301406

 EN301489-6

 EN301489-1

 EN61000-6-3

 EN60950-1

 EN50581

 UL 2017

 C22.2 No.205-12

TECHNICAL SPECIFICATIONS

RF Protocol DECT ULE

Modulation Type GFSK

Signaling Type Non – Emergency signaling

Type (NM)

Frequency 1880–1900 MHz - Europe

1920–1930 MHz - USA/Canada

Event Transmission Flood Alert, Tamper, Keep Alive,

Battery status.

Detection Method External sensor.

Range in open space >500m

Battery Lithium. 3V Type: CR123A

Size: 2/3A

Battery life expectancy >4 years (10 activation per day)

Current Consumptions: Standby 4A

Average 19µA

Maximum (TX) 250mA

Low Battery 2.5VDC

Cut Off Battery 2.3VDC

Transmit Power (Typ.): 23dBm (EURO), 20dBm (USA)

Tamper Switch Back Tamper

Operating temperature -10C to +55C

Dimensions 104mm x 24mm x 22mm

Weight 50 gr. (inc. battery 65 gr.)

Maximum Cable Length 1m

CAUTION !!!

RISK OF EXPLOSION IF BATTERY IS

REPLACED BY DIFFERENT TYPE / MODEL.

DISPOSE USED BATTERIES

ACCORDING TO ITS INSTRUCTIONS

ATTENTION !!!

RISQUE D'EXPLOSION SI LA PILE EST

REMPLACÉE PAR UN TYPE INCORRECT.

CROW ELECTRONIC ENGINEERING LTD. ("Crow") - WARRANTY POLICY CERTIFICATE

This Warranty Certificate is given in favor of the purchaser (hereunder the "Purchaser") purchasing the products directly from Crow or from its

authorized distributor.

Crow warrants these products to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the

last day of the week and year whose numbers are printed on the printed circuit board inside these products (hereunder the "Warranty Period").

Subject to the provisions of this Warranty Certificate, during the Warranty Period, Crow undertakes, at its sole discretion and subject to Crow's

procedures, as such procedures are form time to time, to repair or replace, free of charge for materials and/or labor, products proved to be defective

in materials or workmanship under normal use and service. Repaired products shall be warranted for the remainder of the original Warranty Period.

All transportation costs and in-transit risk of loss or damage related, directly or indirectly, to products returned to Crow for repair or replacement shall

be borne solely by the Purchaser.

Crow's warranty under this Warranty Certificate does not cover products that is defective (or shall become defective) due to: (a) alteration of the

products (or any part thereof) by anyone other than Crow; (b) accident, abuse, negligence, or improper maintenance; (c) failure caused by a product

which Crow did not provide; (d) failure caused by software or hardware which Crow did not provide; (e) use or storage other than in accordance with

Crow’s specified operating and storage instructions.

There are no warranties, expressed or implied, of merchantability or fitness of the products for a particular purpose or otherwise, which extend

beyond the description on the face hereof.

This limited Warranty Certificate is the Purchaser's sole and exclusive remedy against Crow and Crow's sole and exclusive liability toward the

Purchaser in connection with the products, including without limitation - for defects or malfunctions of the products. This Warranty Certificate

replaces all other warranties and liabilities, whether oral, written, (non-mandatory) statutory, contractual, in tort or otherwise.

In no case shall Crow be liable to anyone for any consequential or incidental damages (inclusive of loss of profit, and whether occasioned by

negligence of the Crow or any third party on its behalf) for breach of this or any other warranty, expressed or implied, or upon any other basis of

liability whatsoever. Crow does not represent that these products can not be compromised or circumvented; that these products will prevent any

person injury or property loss or damage by burglary, robbery, fire or otherwise; or that these products will in all cases provide adequate warning or

protection.

Purchaser understands that a properly installed and maintained product may in some cases reduce the risk of burglary, fire, robbery or other events

occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property

loss or damage as a result.

Consequently, Crow shall have no liability for any personal injury; property damage or any other loss based on claim that these products failed to

give any warning.

If Crow is held liable, whether directly or indirectly, for any loss or damage with regards to these products, regardless of cause or origin, Crow’s

maximum liability shall not in any case exceed the purchase price of these products, which shall be the complete and exclusive remedy against

Crow.

CROW ELECTRONIC

ENGINEERING LTD.

12 Kineret St.

Airport City, 70100 Israel

Tel. +972 3 9726000

Fax. +972 3 9726001

sales@crow.co.il

support@crow.co.il

www.thecrowgroup.com

CROW LATIN AMERICA USA INC.

7200 NW 19 st.

Suite 307

Miami FI 33126, USA

Tel. +305 513 4001

Fax. +305 513 4005

rejane@crowlatinamerica.com

www.crowlatinamerica.com

The battery must be

replaced by 3V Lithium

battery Size 2/3A

Models such as:

1. VARTA CR123A

2. GP CR123A

The battery must be replaced

by Size 2/3AA - CR123A

Lithium battery 3V